Honeywell LANSRLU1 Einrichtungshandbuch

7-101002-00

LANSRLU1

Lantronix UDS100

QuickStart User Guide

Available Now At

Click Here

LANSRLU1 Honeywell Access Systems

2 7-101002-00

Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Requirements for WIN-PAK 2.0/Pro R3 and Higher . . . . . . . 3

Requirements for WIN-PAK 1.1x . . . . . . . . . . . . . . . . . . . . . . 3

Troubleshooting Requirements . . . . . . . . . . . . . . . . . . . . . . 3

Pinouts and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assigning the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

DeviceInstaller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Install the DeviceInstaller . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assign IP Address and Network Class . . . . . . . . . . . . . . 5

Programming the UDS100

with Windows Command Prompts . . . . . . . . . . . . . . . . . 8

Serial Programming through HyperTerminal . . . . . . . . . 9

WIN-PAK 2.0/Pro/Intl. R3 Configuration with UDS100 . 10

System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connection Alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Problems and Error Messages . . . . . . . . . . . . . . . . . . . . . . 12

Adapter Pinouts for 9-pin and 25-pin Connectors . . . . . . . 16

7-101002-00 3

Honeywell Access Systems LANSRLU1

Overview

The LANSRLU1 (UDS100) Device Server connects serial devices such as Secu-

rity Alarms and Access Control Devices to Ethernet networks using the IP proto-

col family. The UDS100 connects these devices through a TCP data channel or

through a Telnet connection to computers or another Device Server.

The UDS100 uses the Internet Protocol (IP) for network communications and the

Transmission Control Protocol (TCP) to assure that no data is lost or duplicated,

and that everything sent to the connection arrives correctly at the target.

Requirements for WIN-PAK 2.0/Pro R3 and Higher

•LANSRLU1 at the Remote End

•N-485-PCI-2L (with 25-pin M-M null modem adapter)

Requirements for WIN-PAK 1.1x

•UDS100s

at the Local End

at the Remote End

•485-PCI-2L (with 25-pin M-M null modem adapter)

Troubleshooting Requirements

•9 pin female to 25-pin male serial cable

•Network cross-over cable

Pinouts and Connections

LEDs

DB25Serial Port

RJ45 Ethernet Port

Power Plug

RTS

out

DSRDCD

DTR in

GND CTS RX

*9-30VDC

*+3.3VDC

reg.out

unreg.in out out in

out

DB25 Female DCE Interface RS232

* Optional Power Connection

LANSRLU1 Honeywell Access Systems

4 7-101002-00

LEDs

The UDS100 device uses LEDs to

indicate the following conditions:

•10 Mbps Link/Activity (green)

•100 Mbps Link/Activity (green)

•Collisions

•Diagnostics (red)

•Status (yellow)

Assigning the IP Address

LEDs Definition

10 Mbps Link/Activity steady (green). Valid 10 Mbps network connection.

10 Mbps Link/Activity blinking (green). Network packets transmitting and receiving.

100 Mbps Link/Activity steady (green). Valiid 100 Mbps network connection.

100 Mbps Link/Activity blinking (green). Network packets transmitting and receiving.

Collisions blinking red. Network collisions.

Diagnostics steady red and status

blinking green.

1 blink = EPROM checksum error.

2 blinks = RAM error.

4 blinks = EEPROM checksum error.

5 blinks = Duplicate IP address on networ.k

Diagnostics blinking red and status

blinking green.

4 blinks = Faulty network connection.

5 blinks = No DHCP response.

Status steady green. Serial port not connected to network.

Status blinking green. Serial port connected to network.

Method Description

DeviceInstaller User manually assigns the IP address using a GUI.

The UDS unit must be attached to the network.

ARP and Telnet User manually assigns the IP address and other net-

work settings at a command prompt using UNIX ro a

Windows based system. The user must be logged

onto the configuration port (9999).

Serial Port Login Configure the unit through a serial connection.

Note: The UDS device is shipped with a default IP address of 0.0.0.0.

7-101002-00 5

Honeywell Access Systems LANSRLU1

Programming

DeviceInstaller

The user can manually assign the IP address using the DeviceInstaller, which is

on the product Lantronix CD.

Install the DeviceInstaller

1. Insert the product CD into your CD-ROM drive. The Lantronix UDS100

Device Server window displays.

If the CD does not launch automatically:

a. Click the Start button on the Task Bar and select Run.

b. Enter your CD drive letter, colon, backslash, and deviceinstaller.exe

(e.g., E:\deviceinstaller.exe).

2. Click the DeviceInstaller button. The installation wizard window displays.

3. Respond to the installation wizard prompts. (When prompted to select an

installation type, select Typical.)

Assign IP Address and Network Class

1. Click the Start button on the task

bar and select Programs Device–

Installer DeviceInstaller. The

DeviceInstaller window appears.

2. Observe the menu bar and tool

bar. Select on the tool bar in

order to assign a New IP Address.

A dialogue box will appear

prompting that an Ethernet

(MAC) Address and the desired

IP Address be entered.

3. Enter in the MAC Address and

the IP Address of the UDS100

device.

Note that the appropriate Subnet

Mask is required at this point.

LANSRLU1 Honeywell Access Systems

6 7-101002-00

4. Once the MAC Address, IP

Address and Subnet Mask have

been entered, select the Set IP

Address button.

DeviceInstaller will then per-

form the following steps before

the message 'Assign IP success-

ful!' appears:

• Test for an existing IP…

• Ping the new IP…

5. Then select OK.

6. On the Assign IP Address screen,

select Back.

7. The main DeviceInstaller win-

dow will reappear. On the tool

bar, select .

8. Select 'Start Search' as well as the

'PC Network Class'.

9. After receiving a response from

the unit(s), displaying the

assigned IP, select 'Save'.

10. Select 'OK' on the window con-

firming the successful update of

the unit(s).

11. On the Search Network window,

select 'Back'.

The user will then be back at the

Main DeviceInstaller window.

12. If adding more than one device,

select the one that is to be config-

ured first.

13. On the Menu Bar, select Tool

then Device Manager…

A Device Management window

will appear displaying four man-

agement options.

7-101002-00 7

Honeywell Access Systems LANSRLU1

14. For the purposes of programming

the UDS100, select option four,

'Telnet to Device'.

Connecting through port 9999,

the user will be connected to a

Telnet session.

15. A Lantronix Device Universal

Server DOS screen will appear

prompting the user to press Enter

to go into Setup Mode. Press

<enter>.

The duration of programming

will be completed through the

DOS screen.

16. At the 'Your Choice?' prompt,

Enter "0" then <enter> to go into

Server Configuration.

17. At the IP Address prompt, Enter

the IP Address of the UDS100

then <enter>.

18. At the Gateway IP Address

prompt

a. Hit enter immediately if no

gateway is required.

b. Type 'Y', if a gateway is

used. If the user selects 'Y',

at the Gateway IP Addr

(000) prompt, enter the gate-

way address then <enter>.

19. At the Netmask Number of Bits

for Host Part (0=default) (00)

prompt, enter 8,16 or 24 pending

the subnet mask class being used:

8 = Class C = subnet

255.255.255.0

16 = Class B = subnet

255.255.0.0

24 = Class A = subnet 255.0.0.0

20. Change Telnet Config Password

(N), press <enter>.

The Change Setup Menu will

now re-appear.

21. At the 'Your Choice ?' prompt,

enter "1" thenn <enter> in order

to go into the Channel 1 Configu-

ration.

22. At the Baud Rate prompt, enter

9600 then <enter>.

23. I/F Mode is not used, press

<enter>.

24. At the Flow prompt, type 00 then

<enter> in order to disable Flow

Control.

25. At Port No (10001), type, 3001

then <enter>.

LANSRLU1 Honeywell Access Systems

8 7-101002-00

26. At the ConnectMode (C0)

prompt, enter C1 for remote con-

figuration then <enter>.

27. At the Remote IP Address

prompt, if configuring the

Remote UDS100 at this time,

press the enter key four times so

no Remote IP is assigned.

28. At the Remote (0): prompt, enter

3001then <enter>.

29. Press <enter> through the rest of

the menu options.

The Change Setup Menu will

now re-appear.

30. Type 9, <enter> to Save and Exit.

After Exiting the TELNET con-

figuration screen the user will

then return to the DeviceInstaller

software.

The user will then notice a screen

specifying a Target Source.

31. To test communications, under

the Ports option, enter in 3001

and then select OK.

If able to communicate through

the UDS100 on port 3001, the

user will notice a black screen

with a blinking cursor.

32. Upon completion, exit out of

DeviceInstaller.

Programming the UDS100 with Windows Command Prompts

1. Connect the UDS100 to the net-

work.

2. On the Windows Menu Bar,

select Start > Run.

3. Enter in CMD then <enter>.

4. At the Command Prompt, enter in

the following then press <enter>:

ARP -s_IP Address_MAC

Address,

i.e. ARP -s 192.168.1.14 00-20-

4A-64-CC-3D.

5. In order to confirm the assign-

ment of the IP Address and

MAC, at the next command

prompt enter in ARP -A, <enter>.

6. At the following Command

Prompt, enter in TELNET then

<enter>.

7. Enter in OPEN_IP Address_1

then <enter>,

i.e. OPEN 192.168.1.14 1.

7-101002-00 9

Honeywell Access Systems LANSRLU1

The user will notice an error mes-

sage that reads as follows:

Could not open a connection to

host on Port 1: connection failed

8. At the following Command

Prompt, enter OPEN_IP

Address_9999 then <enter>,

i.e. OPEN 192.168.1.14 9999

9. A Lantronix Device Universal

Server DOS screen will appear

prompting the user to Press Enter

to go into Setup Mode. Press

<enter>.

10. At this point, complete steps #21

through #30 of the IP address

procedure that begins on page 5.

11. Exit the TELNET session.

Serial Programming through HyperTerminal

1. On the Windows Menu Bar, go to

Start > Programs > Accessories >

Communications > HyperTermi-

nal.

2. A Connection Description screen

will appear, prompting the User

to 'enter a name and choose an

icon'. Enter a name and select

OK.

3. A Connect to screen will appear.

Under the category 'Connect

using'. Select the COM Port in

use with the UDS100.

4. At last a COM Properties screen

will appear. Make the following

changes:

Bits per second = 9600.

Data Bits = 8.

Parity = None.

Stop Bits = 1.

Flow Control = None.

5. Select OK.

The user will then notice a blank

screen with a blinking cursor.

6. To enter Setup Mode, while hold-

ing down the 'x' key, cycle power

to the UDS100 (power off and

back on).

7. When the device reports back

information, immediately press

<enter>.

8. At this point, complete steps #21

through #30 of the IP address

procedure that beginns on page 5.

9. Upon completion,exit the Hyper-

Terminal session.

LANSRLU1 Honeywell Access Systems

10 7-101002-00

WIN-PAK 2.0/Pro/Intl. R3 Configuration with UDS100

1. Be sure all devices are properly

configured and attached over the

network.

2. Log into the WIN-PAK 2/Pro

User Interface.

3. On the WIN-PAK Menu Bar, go

to Configuration > Device >

Device Map.

4. Assuming the 485 Loop has

already been configured, right-

click on the 485 and select Con-

figure.

5. Notice two tabs, Basic Informa-

tion and Port Settings. Select the

Port Settings tab.

6. Under Port, press the drop down

arrow and select TCP/IP connec-

tion.

7. At this point, enter an IP Address

or Node name.

8. After the IP Address has been

entered, exit the Loop Configura-

tion by selecting OK.

9. At this point, continue with the

system programming.

10. Upon completion of program-

ming, test communication by Ini-

tializing the panel(s).

Inhaltsverzeichnis

Andere Honeywell Server Handbücher

Honeywell

Honeywell PE SC1430 Technisches Handbuch

Honeywell

Honeywell T610 Technisches Handbuch

Honeywell

Honeywell AutomationServer Bedienungsanleitung

Honeywell

Honeywell Uniformance R300 Bedienungsanleitung

Honeywell

Honeywell Aquatrol W964F Bedienungsanleitung

Honeywell

Honeywell HUS-D4-E-Pro Bedienungsanleitung

Honeywell

Honeywell HP ProLiant DL360P Gen8 Bedienungsanleitung

Honeywell

Honeywell Q7055B1047 Bedienungsanleitung

Honeywell

Honeywell XYR3011 Bedienungsanleitung

Honeywell

Honeywell HAS-QNH Bedienungsanleitung

Honeywell

Honeywell T320 Technisches Handbuch

Honeywell

Honeywell XYR301E Bedienungsanleitung

Honeywell

Honeywell MZ-PCSV74 Technisches Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung