Honeywell ALL-SPEC Bedienungsanleitung

ALL-SPEC_Unit_HON.doc 07/2011 1/9

Installation Instructions for

Honeywell ALL-SPEC Air Sampling Smoke Detection System

1 Operating indicator light

2 Alarm indicator light for detector

module II

3 Alarm indicator light for detector

module I

4 Indicator light for common fault

5 Pre-punched cable entries for connection to the central fire panel or power supply (input/output)

6 Connection pipe system I

7 Connection pipe system II

8 Connection for air return

ALL-SPEC_Unit_HON.doc 07/2011 2/9

Installation of the Detector Module

Please note:

Only the detector modules of the type ASD-TP-05, ASD-TP-01 and ASD-TP-001 that have been approved by the VdS-certification authority with the

approval number G 202064 may be used.

1. Carry out the following works only if the device is powered down.

2. Open the device by carefully unlocking the housing snap-in closures by means of a screwdriver. Then lift the housing lid a little bit.

3. Carefully pull the connection cable of the display board off and remove the housing lid.

Note:

Shall the device only be provided with one detector module, please skip to point 6. Shall the device however be provided with two modules please

follow the following instructions.

4. If you want to install a second detector module you have to recover carefully the ventilator cover for the second air sampling duct (self-adhesive

plastic cover). Take for this if necessary a screwdriver.

5. Break carefully the clasp for the connection of the second pipe system (predetermined breaking point, marked by “II“) with a screwdriver from the

housing.

Note:

The knocked clasp is to removed completely from the device.

6. Make the required settings at the detector module by setting the contacts of switch S1 accordingly (see also “Settings of the detector module”).

7. Carefully spread a bit the support clamps used to fix the detector module in the corresponding mounting position.

8. Carefully place the detector module in between them until it audibly snaps in and thus is fixed by the support clamps.

Note:

Make sure that the inserted detection module is fixed tight and save by the brackets by pressing the brackets additional by hand.

9. Connect the detector module via the ribbon cable with the connection “Head 1” (detector module I) or “Head 2” (detector module II) to the base

board. Note the labelling of the base board.

10. Reconnect the display board to the base board. Note the connections and labelling of the base board.

ALL-SPEC_Unit_HON.doc 07/2011 3/9

Detector Module Settings

In the following tables the switch S1 has two positions:

on off

The standard settings have a grey background.

Setting the response sensitivity

detector module

DM-TP-

S1. 1

S1. 2

0,8 %/m 0,12 %/m on on

0,4 %/m 0,06 %/m off on

1,0 %/m 0,2 %/m 0,03 %/m on off

0,5 %/m 0,1 %/m 0,015%/m off off

Setting the alarm delay

S1. 3 S1. 4

0 seconds off off

10 seconds on off

30 seconds off on

60 seconds on on

Setting the activating threshold

“air flow fault”

S1. 5 S1. 6

I on off

II off on

III off off

IV on on

Setting the delay

“air flow fault”

S1. 7 S1. 8

0.5 minutes off on

2 minutes on off

15 minutes on on

60 minutes off off

Setting the fault signal

S1. 9

non-latched off

latched on

Setting LOGIC

⋅

SENS

S1.10

off off

on on

ALL-SPEC_Unit_HON.doc 07/2011 4/9

JU2

JU3

HEAD 1 HEAD 2DIAG DISPLAY X5 21

JU2

JU3

213

JU2

213

X1 X2 X3 X4

JU4

JU1

JU1 12

JU4

Choose number of the detector modules

The number of fitted detector modules are chosen with the jumper JU4. The following table shows, whether the jumper must be put or not:

X = pin pair bridge

O = pin pair open

The standard settings have a grey background.

Choose number of the detector

modules

Jumper

Pin No.

JU4,

1+2

1 detector module X

2 detector module O

Setting the ventilator voltage

Jumper JU1 allows to set the ventilator voltage on the base board. The following table shows whether the jumper is set or not:

X = pin pair bridged

O = pin pair open

The standard setting has a grey background.

Setting the ventilator voltage

Jumper

Pin No.

JU1,

1+2

6,9 V X

9 V O

ALL-SPEC_Unit_HON.doc 07/2011 5/9

Setting the function of the fault contact

The contact type (break contact or make contact) of the collective fault is set using the jumper JU 2 and JU 3.

Fault contact detector module I = Jumper JU2

Fault contact detector module II = Jumper JU3

The following table shows the positioning of the jumpers:

X = pin pair bridge

O = pin pair open

The standard settings have a grey background.

Setting the collective fault contact

Jumper

Pin No.

JU2/3

1+2

JU2/3

2+3

break contact X O

make contact O X

Device Supports

Support type MT-1

horizontal installation

Support type MT-1

vertical installation

ALL-SPEC_Unit_HON.doc 07/2011 6/9

Installation of the device

General information:

-When choosing the installation location make sure the displays of the device are clearly visible.

-Screw the air sampling smoke detection system either directly to the wall with its bottom casing or mount it by means of a special support (type

MT-1). This support allows to mount the device also to racks for example.

-The air outlet of the device must not be blocked. (The distance between the air outlet and adjacent objects (e.g. wall) is to be at least 10 cm.)

-The air sampling smoke detection system can be mounted with the air sampling pipe connector(s) pointing upwards or downwards (If necessary,

turn the housing-lid by 180°). If the air sampling pipe connector(s) point downwards make sure no impurities enter the air outlet which then

points upwards.

Procedure:

1. First, clearly mark the fixing points for mounting the device. If necessary, use the provided drilling jig. Fix the device using four screws (max. ∅

of 6 mm for wall mounting and max. ∅of 4 mm for mounting by means of the device support MT-1) in order to guarantee a safe fixing and to

limit vibrations which occur.

2. Fix the device by means of four screws in accordance with the mounting type to the wall or the device support. Make sure the device is not fixed

under mechanical tension or the screws are not tightened too much. Otherwise the device might be damaged, or unintended. secondary noise

may arise.

Note:

To balance unevenness and/or to avoid vibrations vibration dampers need to be installed.

3. Carefully break out of the housing the required cable entries (max. 5 x M20 und 2 x M25). If required, use a screwdriver.

4. Carefully equip the cable entrie(s) according to requirements with M20 or M25 glands (2x M25, 1x M20 included in the delivery) by inserting

them into the corresponding cable entry/entries.

5. Pass the connection cable(s) (max. 1.5 mm²) required to wire the device through the suitable cable entry/entries into the device and cut it to the

required length within the device.

6. Wire the device according to the following connection diagram.

ALL-SPEC_Unit_HON.doc 07/2011 7/9

+24V

internal connection base board

+24 V

DJ 1191

DJ 1192

+24V

connection to central fire panel

DJ 1191

DJ 1192

connection to central fire panel

Connection

X6, 1

X6, 2

X6, 3

contact of the first alarm relay (make contact)

centre tap of first alarm relay

contact of the first alarm relay (break contact)

X6, 4

X6, 5

+ external response indicator for

first detector module

– external response indicator for

first detector module

X6, 6

X6, 7

+ 24 V reset input

0 V reset input

X6, 8

X6, 9

+ 24 V supply voltage

0 V supply voltage

X7, 1

X7, 2

fault contact 2nd detector module

(connection 1)

fault contact 2nd detector module

(connection 2)

X7,3

X7, 4

X7, 5

contact of the 2nd alarm relay

(make contact)

centre tap of 2nd alarm relay

contact of the 2nd alarm relay

X7, 6

X7, 7

+ external response indicator for 2nd

detector module

– external response indicator for 2nd

detector module

X7, 8

X7, 9

fault contact first detector module

(connection 1)

fault contact first detector module

(connection 2)

ALL-SPEC_Unit_HON.doc 07/2011 8/9

Flow-Init

Commissioning

1. Make sure first that the device has been in operation for at least 30 minutes prior to the air flow initialization in order to reach the operating tem-

perature.

2. In order to initialize the connected pipe system, press the Flow-Init-button S2 (see figure) of the corresponding detector module until the green

operating indicator light of the device starts flashing. The initialization is terminated

after approx. 5 seconds. After a successful initialization the operating indicator light is lit permanently.

3. During and after initialization the pipe system must no longer be changed. Even the ventilator voltage of the device must no longer be modified

after initialization. Otherwise the initialization must be carried out again:

ALL-SPEC_Unit_HON.doc 07/2011 9/9

Conformity certification pursuant to EU Construction Products Directive 89/106/EEC

•The conformity of the „air sampling smoke detector for fire detection and fire alarm systems in buildings“ according to DIN EN 54-20

has been established by a test at the VdS laboratory.

•The EC certificate of conformity has been issued by notified product certification body (ID no. 0786, VdS).

•The CE designation according to DIN EN 54-20 has been carried out.

0786

WAGNER Group GmbH

Schleswigstrasse 1 - 5 30853 Langenhagen

Nr. 0786 – CPD – 20685

EN 54-20: 2006

Air sampling smoke detector for fire detection

and fire alarm systems in buildings

0,015 % light obscuration/m

Class: A, B and C

0,1 % light obscuration/m

Class: A, B and C

0,5 % light obscuration/m

Class: A, B and C

Honeywell Life Safety Systems

140 Waterside Road

Hamilton Industrial Park

Leicester

LE5 1TN

Tel (+44) 116 246 2000

Inhaltsverzeichnis

Andere Honeywell Rauchmelder Handbücher

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell 5806W3 Montageanleitung

Honeywell

Honeywell XLS-278 Bedienungsanleitung

Honeywell

Honeywell Notifier FDU-80 Bedienungsanleitung

Honeywell

Honeywell LT-200 MI-FL20 Series Bedienungsanleitung

Honeywell

Honeywell Photoelectronic Smoke/Temperature Detector... Montageanleitung

Honeywell

Honeywell MS-5UD Series Bedienungsanleitung

Honeywell

Honeywell GasAlertMicro 5 Bedienungsanleitung

Honeywell

Honeywell JTYJ-GD-01BW Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms SD365R Bedienungsanleitung

Honeywell

Honeywell FCI 2451 Series Bedienungsanleitung

Honeywell

Honeywell SiXSMOKE Bedienungsanleitung

Honeywell

Honeywell SS4-AI Bedienungsanleitung

Honeywell

Honeywell TC846A1005 Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5806 Bedienungsanleitung

Honeywell

Honeywell TC842B1007AE Bedienungsanleitung

Honeywell

Honeywell FireLite BEAM355 Bedienungsanleitung

Honeywell

Honeywell SK-Beam Bedienungsanleitung

Honeywell

Honeywell Notifier FSP-851 Bedienungsanleitung

Honeywell

Honeywell FAAST LT Bedienungsanleitung

Honeywell

Honeywell SiX Series Bedienungsanleitung

Honeywell

Honeywell D355PL Bedienungsanleitung

Honeywell

Honeywell Notifier VESDA-E VEA Series Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung