Honeywell SS4-AI Bedienungsanleitung

Installation Guide and Operating Manual

Infrared (IR) Digital

Electro-Optical Fire Detector

Model SS4-AI (For Special Applications Only – Consult Factory)

Stand-Alone Mode

OPERATOR MANUAL // NOTICES AND TRADEMARKS

HONEYWELL 1

Notices and Trademarks

While this information is presented in good faith and believed to be

accurate, Honeywell disclaims the implied warranties of merchantability

and fitness for a particular purpose and makes no express warranties

except as may be stated in its written agreement with and for its

customers.

In no event is Honeywell liable to anyone for any indirect, special or

consequential damages. The information and specifications in this

document are subject to change without notice.

The detector must be installed only by qualified professional personnel in

accordance with local codes.

The protection provided by the gas detector may be impaired if it is used in

a manner not specified by Honeywell Analytics.

ACCTTL, ALERT-1, ALARM-2, ALERT-1: ALARM 2, ALERT-1: ALARM-2,

ATAG, Clean Room Sentry, COP-i, Complete Optical Path Integrity, CM1,

CM1-A, DartLogic, FireLogic, Fire Signature Analysis, FireBusI, FireBusII,

FirePic, FirePicII, FirePicIII, FirePix, FirePicture, FSC, Fire Sentry

Corporation, Fire Sentry Corp., FSX, All FSX Nomenclature Variations

(such as: FS2, FS2X, FS3, FS3X, FS4, FS4X, FS5, FS5X, FS6, FS6X,

FS7, FS7X, FS8, FS8X, FS9, FS9X, FS10X, FS10X, FS11, FS11X, FS12,

FS12X, FS14, FS14X, FS15, FS15X, FS16, FS16X, FS17, FS17X FS18,

FS18X, FS19, FS19X, FS20, FS20X, FS24, FS24X, FS24XN, FS26,

FS26X, FS26XN), FS7-2173-2RP, FS System 7, FS System 10, FS7-2173,

FS7-2173-RP, FS2000, FS System 2000, High Speed Flame &

Surveillance Detector, Multi-Spectrum QuadBand Triple IR, Multi-Spectrum

TriBand, Multi-Spectrum Tri-Band, Near Band Infrared, Near Band IR,

NearBand IR, QuadBand IR, Room Sentry, RS, RS2, SM2, SM3, SS, SS2,

SS2X, SS2-A, SS3, SS3-A, SS3X, SS4, SS4-A, SS4X, SnapShot, SLR-BIT,

SuperBus, SuperSentry, System 2000, Tri-Mode Plot, QuadBand Triple IR

Plus, TriBand, Tri-Band, “FS & FSC triangle logo’s”, WBIR, Wide Band

Infrared, WideBand IR, Wide Band IRare registered trademarks of

Honeywell International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Analytics

OPERATOR MANUAL // SYMBOL DEFINITIONS

HONEYWELL 2

Symbol Definitions

The following table lists those symbols used in this document to denote

certain conditions.

Symbol Definition

ATTENTION: Identifies information that requires special

consideration.

TIP: Identifies advice or hints for the user, often in terms of

performing a task.

REFERENCE-EXTERNAL: Identifies an additional source of

information outside of this bookset.

REFERENCE-INTERNAL: Identifies an additional source of

information within this bookset.

Indicates a situation which, if not avoided, may result in

equipment or work (data) on the system being damaged or lost,

or may result in the inability to properly operate the process.

CAUTION: Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury. It may also

be used to alert against unsafe practices.

CAUTION:Symbol on the equipment refers the user to the

product manual for additional information. The symbol appears

next to required information in the manual.

OPERATOR MANUAL // TABLE OFCONTENTS

HONEYWELL 3

TABLE OF CONTENTS

PAGE

SECTION 1 FAMILIARIZATION ..................................................................... 4

1.1 Introduction...................................................................................... 4

1.2 Stand-Alone Operation.....................................................................4

1.3 FS2000 System Operation................................................................4

1.4 Overview .........................................................................................5

1.4.1 Model SS4-AI Infrared Flame Detector................................. 5

1.4.2 Detection Range..................................................................5

1.4.3 Field-of-View.......................................................................5

1.4.4 Configuration Settings ......................................................... 5

1.4.5 Testing................................................................................7

SECTION 2 INSTALLATION .......................................................................... 8

2.1 Installation Procedure ......................................................................8

2.1.1 Installation Precautions........................................................8

2.1.2 Conduit Installation.............................................................. 8

2.1.3 Wiring Recommendations ....................................................9

2.1.4 Power Supply Considerations............................................... 9

2.2 Enclosure Installation..................................................................... 10

2.4 Configuring and Wiring Detectors ................................................... 11

SECTION 3 MAINTENANCE AND TROUBLESHOOTING...............................14

3.1 Personnel...................................................................................... 14

3.2 Cleaning Windowed Enclosures and Detectors................................ 14

3.3 Model SS4-AI Detector Faults......................................................... 15

3.3.1 Detector Faults.................................................................. 15

3.4 Model SS4-AI Detector Module Replacement.................................. 15

3.5 Detector Repair.............................................................................. 16

DETECTOR PINOUT DATA.......................................................... 17

TABLE 1: Stand-Alone Model SS4-AI Detector Connectors

Pinouts.............................................................................. 17

TABLE 2: Configuration Dip Switch Settings................................... 12

INDEX.......................................................................................13

OPERATOR MANUAL //

SECTION 1: FAMILIARIZATION

HONEYWELL 4

SECTION 1: FAMILIARIZATION

1.1 Introduction

The Model SS4-AI Infrared Flame Detectors can be used in the FS2000

Fire Early Warning System or in the Stand-Alone mode. This model is

housed in an Explosion-Proof enclosure and incorporates built in optical

testing of both the Detectors and lens.

The Detector maximum alarm range is 45 feet for a one square foot

gasoline with a 120 degree circular field of view. This Detector design

features dynamic signal processing that utilizes infrared band and visible

band sensor elements. For Special Applications Only – Consult

Factory.

The only difference between a FS2000 System Model SS4-AI

Detector and a Stand-Alone SS4-AI Detector is how each is wired

and the use of the fault relay. However, there are operational

advantages when the Model SS4-AI Detector is connected to a

FS2000 Controller and FireBus.

The Model SS4-AI Detector also has the flexibility to be re-configured in

the field. It is simple to install and operate because its built in self-testing

does most of the work. The only real maintenance is to wipe the Detector

window lens clean and perform any periodic testing required by the

manufacturer of the Fire Control and Suppression System.

1.2 Stand-Alone Operation

For Stand-Alone operation, the Model SS4-AI Detector may be connected

to a FM/UL Approved Fire/Security Panel. The Model SS4-AI Detector

operates on 24 volts DC. The Model SS4-AI Detector, when operated in

the Stand-Alone mode, uses its Fire, Fault, and Verify (optional) relays to

interface to FM/UL Approved Fire /Security Panels. For Stand-Alone

operation, the Model SS4-AI's Fault relay is automatically configured by

its on-board microcomputer. The input current of the Model SS4-AI

Detector increases about 15 milliamps in the Stand-Alone mode compared

to with connected to theFS2000 System. The Fault relay is not available

for use when the Model SS4-AI Detector is wired to the FS2000 System.

1.3 FS2000 System Operation

For FS2000 System operation, the Model SS4-AI Fire and Fault signals are

sent digitally to the FS2000 System Controller using the four wire FS2000

FireBus. The FireBus provides the 24 volts DC power for the Model SS4-

AI Detector and RS-485 digital communication (Refer to Honeywell

Analytics document MN0003 entitled "FS2000 FIRE EARLY WARNING

SYSTEM - INSTALLATION and OPERATIONS GUIDE"). For special

remote alarm applications, users may connect directly to the Model SS4-

AI's Fire four pin relay connector. (Note: When the Model SS4-AI Detector

is connected to the FS2000 System using FireBus communication, the

Controller automatically disables the Model SS4-AI's Fault relay.)

OPERATOR MANUAL //

SECTION 1: FAMILIARIZATION

HONEYWELL 5

1.4 Overview

1.4.1 Model SS4-AI Infrared Flame Detector

The Model SS4-AI Infrared (IR) Flame Detectors are micro-computerized

devices that see the visible and infrared spectral bands. The SS4-AI

Detector Module is contained in an Explosion-Proof and Weather-Proof

housing which is approximately 4 3/4 inches in diameter and 4 3/4 inches

long. The housing has two integral 3/4 inch NPT conduit openings for

wiring and an optional Swivel Mount (Model SM4) for greater flexibility in

mounting locations.

There are two (2) LED's on the Model SS4-AI Detector that indicate the

state of the Detector. During normal operation both of the LED's blink will

every 10 seconds.

If a Model SS4-AI Detector has a Fault, it de-energizes its Fault relay and

turns on one (1) of its LED’s. (The LED will not light if the Fault is a “No

Power Fault”.) If the Fault condition is cured, such as a “Low Voltage

Fault”, the Detector will automatically return to Normal Operation. Faults

caused by Excessive Input Voltage or temperatures outside the operating

temperature range require factory re-certification. Re-certification required

Faults are indicated by both LED’s rapidly blinking. (about 2 Hz.)

If a Model SS4-AI Detector alarms to a fire, it energizes its Fire relay and

turns on its two LED's in the following sequence. One LED is turned on

immediately and the second LED will rapidly blink for several seconds

indicating that the Detector's FirePic is being permanently stored in the

Detector's solid-state memory. (FirePic is the several seconds of Detector

data that preceded an alarm event.) Once the FirePic data is stored the

second LED will remain on.

1.4.2 Detection Range

The detection range of the detector is field adjustable between 15 (fifteen)

and 45 (fourtyfive) feet to an industry-standard one square foot gasoline

pan fire within 5 seconds. Each detection range is calibrated to a one

square foot fire. The Detector’s ranges are optimized but not limited to a

specific distance. A larger size fire outside the set range may cause the

Detector to alarm based on the “Inverse Square Law” for radiated energy.

1.4.3 Field-of-View

120 degrees circular - minimum. The fire emissions received by the

detector diminish at extreme range and edges of the field-of-view. It is

recommended that the detector be pointed at the fire threat area for the

fastest response times to the smallest size fire. When multiple detectors

are used to cover large areas the Field-of-Views should overlap to insure

complete coverage of the fire threat area. The Field-of-View is not limited

to 120 degrees, larger fires outside the 120 degree Field-of-View may

cause the detector to alarm.

1.4.4 Configuration Settings

The SS4-AI Detector may be reconfigured in the field for special

applications. The configuration of the Detector is set from a dip switch

located on the middle circuit board of the SS4-AI Module. These settings

OPERATOR MANUAL //

SECTION 1: FAMILIARIZATION

HONEYWELL 6

allow the detectors to be optimized for the specific application. The DIP

switch settings for each configuration are listed in Table 2: Configuration

Dip Switch Settings on page 12. The reconfigurable options include:

1. Fire Verify Relay - The Verify Relay may be disabled or enabled

with several Verify Time settings. It also may be set to act as another Fire

Relay. The Verify Time may be set from 5 to 30 seconds in 5 second

increments. The Factory setting is the Verify Relay is Disabled.

With the Verify Relay enabled and a Verify Time is set the Verify Relay will

energize and the Fire Relay will de-energize if the fire conditions are still

present at the end of the Verify Time. If the fire conditions are not present

the Detector will wait 5 seconds plus another Verify Time period to test for

the fire conditions. This wait and verify time will repeat 10 times or until

the fire is verified. This ends the verify process. If the fire is not verified

the Fire Relay will remain energized unless Non-Latching mode is set. If a

subsequent fire is detected the entire verify process will repeat. The state

of the Fire and Verify Relay after the verify process will depend upon

whether Latching or Non-Latching mode is set.

NOTE: When the Verify Relay is enabled and Verify Time is

set the Fire Relay will de-energize when the Verify Relay is energized.

2. Latching / Non-Latching - The Fire Relay and Verify Relay may be

set in a Latching or Non-Latching mode. If Latching mode is set the Fire or

Verify Relay will remain energized until the Detector is reset (Powered

down and up). When Non-latching mode is set the Fire Relay will reset

after 10 seconds. Unless the Verify Relay is enabled with a Verify Time,

then the Fire Relay will remain energized until the Verify Relay is energized

or until the end of the verify process. (see Fire Verify Relay above.) If the

Verify Relay is energized the Verify Relay will de-energize after 10

seconds. The Factory setting is Latching. Non-Latching mode may not

meet some Fire Codes. Consult with authority having jurisdiction before

using the non-Latching setting.

3. Test Period - This setting if for the Through-the-Lens test. The

Through-the-Lens test is run periodically. The test period may be set to 6

or 30 minute periods. The Factory setting is 30 minutes. If 6 minute

periods are set this may affect the life expectancy of the source tube. The

6 minute period may be required in applications where the lens is obscured

with great frequency.

4. Fire Detection Range Setting - 15, 30, or 45 feet. The SS4-AI

Detector has been calibrated to alarm on an industry standard 1 sq. ft.

gasoline fire for each of the range settings. If the Range is set to 15 feet,

the detector will require a much larger gasoline fire at 45 feet to declare an

alarm. These settings are not simply sensitivity settings. They are

calibrated to the characteristics of fire emissions at the set ranges. The

Factory setting is 45 feet. This setting should only be changed if the

detector is located close to the fire threat area and there is abnormally high

IR activity.

OPERATOR MANUAL //

SECTION 1: FAMILIARIZATION

HONEYWELL 7

1.4.5 Testing

The SS4-AI Detector has both active and passive built-in self-test systems.

The detector uses passive testing for virtually all internal electronic

systems.

The Model SS4-AI Detectors and the system they are connected to should

be periodically manually tested to insure proper function of the entire Fire

Protection System. To test the Model SS4-AI Detectors manually (where

open fires are might be a safety hazard) for both optical path and window

cleanliness, use a Honeywell Analytics Model FT-2145 Test Lamp.

OPERATOR MANUAL // SECTION 2: INSTALLATION

HONEYWELL 8

SECTION 2: INSTALLATION

2.1 Installation Procedure

This section describes the installation of the Model SS4-AI Detector for the

Stand-Alone mode. It is recommended that junction boxes be used to wire

the Model SS4-AI Detectors. Determine a mounting location for the

detector which is within the detectors range (see Detection Range and

Field-of-View) and has a clear view of the fire threat area. Where multiple

detectors are used to cover a large area, the detectors should be located to

allow overlapping Field-of-Views. Determine the configuration settings for

the device and the number of connections to be used. (Fire, Fire Verify,

Fault, and Power) The configuration settings and number of connections

will depend on the Detection Range desired and the type of Fire Control

Panel used. For Configuration information see the Dip Switching Setting

chart and the manual for your Fire Control Panel.

2.1.1 Installation Precautions

The following precautions should be observed during installation of Model

SS4-AI Detectors.

1. Double-check to make sure that the external electrical power is

turned OFF before connecting to the Model SS4-AI Detector.

2. Do not handle the Model SS4-AI Detector's module (with its

printed circuit boards) without being adequately grounded.

Printed circuit board components are susceptible to damage from

electrostatic discharge. Grounding may be accomplished by

wearing an anti-static wrist strap connected to an earth ground.

2.1.2 Conduit Installation

Model SS4-AI Detectors should be located to cover the specific "fire threat"

areas.

When planning the conduit, observe the following recommendations.

1. If only one of the two ½ inch NPT conduit openings on the Model

SS4-AI Detector enclosure is used, seal the unused opening with a

threaded plug.

2. In areas where moisture may accumulate, install an approved

conduit trap or drain.

3. A seal shall be installed within 6 inches of the enclosure for

applications requiring a Class I, Div. 1 Explosion-Proof rating.

OPERATOR MANUAL // SECTION 2: INSTALLATION

HONEYWELL 9

2.1.3 Wiring Recommendations

The Honeywell Analytics recommends using junction boxes to help prevent

problems with intermittent connections. Install a junction box near each

Model SS4-AI Detector location. Next, wire each Model SS4-AI Detector to

its junction box. Use screw-down terminal strips inside the junction box to

make the connections to the Detector's terminals and a UL/FM Approved

Fire Alarm Panel. Use UL/FM Approved junction boxes and terminal strips.

Avoid wire splices. However, if wire splices are necessary, solder all

splices. The use of good wiring practices will greatly improve the ease of

installation, improve reliability, and allow easier servicing.

2.1.4 Power Supply Considerations

The Model SS4-AI Detector uses 24 volts DC at a maximum current of

75 milliamps. Make sure that the Panel's power supply can handle the

current load of the total number of Model SS4-AI Detectors connected to

it. For example, if 10 Model SS4-AI Detectors are used on one Panel's

power supply, (multiply 10 times 75 milliamps), the Panel's power supply

must be able to handle at least 750 milliamps (3/4 amps). This current

load must also be considered when calculating the Panel's power backup

requirements for 24 hour backup.

Figure 2: Model SS4-AI Detector Swivel Mount

Inhaltsverzeichnis

Andere Honeywell Rauchmelder Handbücher

Honeywell

Honeywell SiXSMOKE Bedienungsanleitung

Honeywell

Honeywell JTYJ-GD-01BW Bedienungsanleitung

Honeywell

Honeywell DFS8M Bedienungsanleitung

Honeywell

Honeywell TC846A1005 Bedienungsanleitung

Honeywell

Honeywell FireLite BEAM355 Bedienungsanleitung

Honeywell

Honeywell Ademco 5806 W3 Betriebsanleitung

Honeywell

Honeywell SiXCOMBO Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell SiX Series Bedienungsanleitung

Honeywell

Honeywell FCI 2151 Bedienungsanleitung

Honeywell

Honeywell 5193SD Bedienungsanleitung

Honeywell

Honeywell ALL-SPEC Bedienungsanleitung

Honeywell

Honeywell FCI 1400 Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms BEAM355A Bedienungsanleitung

Honeywell

Honeywell Velociti 3 Series Bedienungsanleitung

Honeywell

Honeywell D355PL Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell SK-Beam Bedienungsanleitung

Honeywell

Honeywell FMST FXV(E) Series Bedienungsanleitung

Honeywell

Honeywell Notifier VESDA-E VEA Series Bedienungsanleitung

Honeywell

Honeywell FCI 2451 Series Bedienungsanleitung

Honeywell

Honeywell TC842B1007AE Bedienungsanleitung

Honeywell

Honeywell FAAST LT Bedienungsanleitung

Honeywell

Honeywell 5806W3 Montageanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung