Honeywell FCI 1151 Bedienungsanleitung

DESCRIPTION

TheSystemSensor1151lowprofileionizationtypesmoke

detectors are specifically designed to meet the performance

requirements of fire detection/alarm systems. The 1151 ion-

ization detector uses a state-of-the-art, dual unipolar sensing

chamber. The detector is designed to provide open area de-

tection and, when installed in a two-wire base, is compatible

with FCI fire alarm control panels. The detector’s operation

and sensitivity can be tested in place.

The 1151 detector is of plug-in construction and plugs into

the same base as the System Sensor 2151photoelectronic

smoke detector, making both models interchangeable. Bases

areavailablefortwo-wire,four-wire,120VACfour-wireop-

eration and also with an audible sounder.

Two visible LEDs on each detector flash every ten seconds

indicating that power is being applied to the detector. The

LEDs light steadily when the detector is in alarm. A remote

LED annunciator is available as an optional accessory.

The 1151 detector is Listed for use inside ducts up to a ve-

locity of 500 FPM.

Functional testing is performed by placing a test magnet

against the cover. The LED on the detector should light

within 30 seconds.

Field metering of detector sensitivity may be performed

with the aid of a voltmeter and Test Kit, MOD 400R.

APPROVALS

SPECIFICATIONS

Sensitivity 1.9 %/ft. (nominal)

Operating voltage 15 - 32 VDC peak

Standby current 200 uA max. avg.

Operating temperature 32 to 120oF(0to49

oC)

Relative humidity 10 to 93 % (non-condensing)

Air velocity 500 feet per minute maximum

Construction Off-white flame retardant plastic

Diameter 4 inches (10.2 cm)

Height 1.7 inches (4.2 cm)

Weight 3.6 oz. (104 g)

1151

SYSTEM SENSOR

LOW PROFILE, IONIZATION

PLUG-IN SMOKE DETECTOR

9020-0582/Ver. 1.1

16 Southwest Park, Westwood, MA 02090 USA TEL: (781) 471-3000 FAX: (781) 471-3099

Specifications are provided for information only, are not intended to be used for installation purposes, and are believed to be accurate. However, no responsibility is assumed by Fire Control

FEATURES

·Unique Dual Unipolar Sensor

Provides Exceptional Stability

·Low Profile Construction

·Easy plug-in of the Head to Base

·Tamper-resistant Feature

·Test Switch

·360oView Angle Of Alarm LEDs

·Compatible with FCI Control Panels

·Audible Sounder Base (Optional)

·Field Metering of Detector Sensitivity

·Removable Insect Screen and Cover

for Field Cleaning

·Insect-resistant Screening

(.020"/.508 mm openings)

An ISO 9001 Certified Company

MOUNTING

·On a 4-inch square box with or without plaster

ring. Minimum depth 1.5 inches.

·On a 3.5-inch octagonal box. Minimum depth

1.5 inches.

INSTALLATION

Place the detector into the detector base. Turn the de-

tector clockwise until the detector locks into place.

To use the tamper-proof feature, break the smaller tab

on the scribed line in the tamper proof tab located on the

detector mounting bracket. Install the detector. To re-

move the detector from the base when using the tam-

per-proof feature, insert the blade of a small

screwdriver into the hole on the side of the base and

push the plastic lever away from the detector head. This

will allow the detector to be rotated counterclockwise

for removal. NOTE: The decorative ring must be re-

moved in order to remove the head when using the tam-

per-proof feature.

The tamper-proof feature may be defeated perma-

nently by breaking the plastic lever off the base.

NOTE: The number of two-wire smoke detectors

which can be accommodated per zone varies with dif-

ferent control panels. Consult the control panel in-

struction manual to determine the capacity.

RefertoNFPA72,Chapter5-3, “SmokeSensingFire

Detectors” for spacing, location of detectors and other

guidelines.

TESTING

Detectors may be tested in the following ways:

·Place a test magnet against the detector

as directed in the installation instructions.

The detector should go into alarm within

30 seconds.

·Field metering of detector sensitivity may be

performed with the aid of a voltmeter and Test

Kit, MOD 400R. For the complete procedure,

refer to the Installation and Maintenance

Instructions furnished with each detector.

MAINTENANCE

Cleaning programs should be adapted to the individ-

ual environment. We recommend at least an annual

cleaning of the unit. The detector screen and cover as-

sembly can be removed, revealing the sensing cham-

ber. Avacuum cleaner can be used to remove dust from

the screen, cover and sensing chamber. For the com-

plete procedure, refer to the Installation and Mainte-

nance Instructions furnished with each detector.

2of2 9020-0582

ORDERING AND TECHNICAL INFORMATION

Model Contacts Description

1151 Ionization Detector

B110LP Base, Two-wire

B112LP Form A & C Base, four-wire, 24 VDC operation

B114LP Form A, C & Supv. Base, four-wire, 120 VAC operation

B401BH Base, four-wire, with audible sounder

RA-400Z Remote Alarm Indicator

PAM-1 Form B End of Line Relay, 24 VDC

MOD 400R Test Kit

Andere Honeywell Rauchmelder Handbücher

Honeywell

Honeywell Silent Knight SK-Duct Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms D350RPL Bedienungsanleitung

Honeywell

Honeywell Xtralis FAAST FLEX FLX-010 Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell Fire Sentry SS4-AUV Bedienungsanleitung

Honeywell

Honeywell TC842B1007AE Bedienungsanleitung

Honeywell

Honeywell SK-Beam Bedienungsanleitung

Honeywell

Honeywell IPGSM-DP Montageanleitung

Honeywell

Honeywell SS4-A HART Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms SD365 Bedienungsanleitung

Honeywell

Honeywell SS4-AI Bedienungsanleitung

Honeywell

Honeywell HI-SPEC Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms Innovair flex D365PL Bedienungsanleitung

Honeywell

Honeywell FS10-R Bedienungsanleitung

Honeywell

Honeywell Velociti 3 Series Bedienungsanleitung

Honeywell

Honeywell Notifier VESDA-E VEA Series Bedienungsanleitung

Honeywell

Honeywell 5193SD Bedienungsanleitung

Honeywell

Honeywell LT-200 MI-FL20 Series Bedienungsanleitung

Honeywell

Honeywell NOTIFIER FSP-951T-SELFT Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms BEAM355A Bedienungsanleitung

Honeywell

Honeywell V-PLEX 5192SD Bedienungsanleitung

Honeywell

Honeywell SS4-A2 Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung