Honeywell FS10-R Bedienungsanleitung

Installation Guide and Operating Manual

Multi-Spectral Digital Infrared

Electro-Optical Fire Detector

Unitized, Two Stage, Quick Response

FSC Model Nos. FS10-R & FS10-RN with Wide Band IR

FS System 10TM Digital Fire Detection/Process Control System

OPERATOR MANUAL // NOTICES AND TRADEMARKS

HONEYWELL 2

Notice

and Trademarks

While this information is presented in good faith and believed to be

accurate, Honeywell disclaims the implied warranties of

merchantability and fitness for a particular purpose and makes no

express warranties except as may be stated in its written

agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or

consequential damages. The information and specifications in this

document are subject to change without notice.

The detector must be installed only by qualified professional

personnel in accordance with local codes.

The protection provided by the gas detector may be impaired if it is

used in a manner not specified by Honeywell Analytics.

ACCTTL, ALERT-1, ALARM-2, ALERT-1: ALARM 2, ALERT-1:

ALARM-2, ATAG, Clean Room Sentry, COP-i, Complete Optical

Path Integrity, CM1, CM1-A, DartLogic, FireLogic, Honeywell

Analytics VSD-8 Honeywell Analytics VSD-8 Visual Smoke

Detection System, VSD-4, VSD-8, Fire Signature Analysis,

FireBusI, FireBusII, FirePic, FirePicII, FirePicIII, FirePix,

FirePicture, FSC, Honeywell Analytics, Honeywell Analytics, FSX,

All FSX Nomenclature Variations (such as: FS2, FS2X, FS3,

FS3X, FS4, FS4X, FS5, FS5X, FS6, FS6X, FS7, FS7X, FS8,

FS8X, FS9, FS9X, FS10X, FS10X, FS11, FS11X, FS12, FS12X,

FS14, FS14X, FS15, FS15X, FS16, FS16X, FS17, FS17X FS18,

FS18X, FS19, FS19X, FS20, FS20X, FS24, FS24X, FS24XN,

FS26, FS26X, FS26XN), FS7-2173-2RP, FS System 7, FS System

10, FS7-2173, FS7-2173-RP, FS2000, FS System 2000, High

Speed Flame & Surveillance Detector, Multi-Spectrum QuadBand

Triple IR, Multi-Spectrum TriBand, Multi-Spectrum Tri-Band, Near

Band Infrared, Near Band IR, NearBand IR, QuadBand IR, Room

Sentry, RS, RS2, SM2, SM3, SS, SS2, SS2X, SS2-A, SS3, SS3-A,

SS3X, SS4, SS4-A, SS4X, SnapShot, SLR-BIT, SuperBus,

SuperSentry, System 2000, Tri-Mode Plot, QuadBand Triple IR

Plus, TriBand, Tri-Band, “FS & FSC triangle logo’s”, WBIR, Wide

Band Infrared, WideBand IR, Wide Band IRare registered

trademarks of Honeywell

International Inc.

OPERATOR MANUAL // NOTICES AND TRADEMARKS

HONEYWELL 3

Other brand or product names are trademarks of their

respective owners.

Honeywell Analytics









 !"#$%" %

OPERATOR MANUAL // ABOUT THIS DOCUMENT

HONEYWELL 4

About This Document

Read and understand this manual before installing or

operating equipment.

No part of this document may be copied or reproduced without the

express written permission of Honeywell Analytics.

This manual is subject to change without notice.

OPERATOR MANUAL // SYMBOL DEFINITIONS

HONEYWELL 5

SymbolDefinitions

The following table lists those symbols used in this document to

denote certain conditions.

Symbol Definition

ATTENTION: Identifies information that

requires special consideration.

TIP: Identifies advice or hints for the user,

often in terms of performing a task.

REFERENCE-EXTERNAL: Identifies an

additional source of information outside of

this booklet.

REFERENCE-INTERNAL: Identifies an

additional source of information within this

booklet.

Indicates a situation which, if not avoided,

may result in equipment or work (data) on

the system being damaged or lost, or may

result in the inability to properly operate the

process.

CAUTION: Indicates a potentially

hazardous situation which, if not avoided,

may result in minor or moderate injury. It

may also be used to alert against unsafe

practices.

CAUTION:Symbol on the equipment refers

the user to the product manual for

additional information. The symbol appears

next to required information in the manual.

OPERATOR MANUAL // TABLE OF CONTENTS

HONEYWELL 6

Table of Contents

Notice

and Trademarks

.................................................................2

About This Document

.....................................................................4

SymbolDefinitions ........................................................................5

Table of Contents..........................................................................6

SECTION 1: INTRODUCTION........................................................8

1.1 Application.......................................................................................8

1.2 Responses.......................................................................................8

1.3 Input Power Requirements..............................................................8

1.4 FirePicTM ..........................................................................................8

1.5 No Silicone Used.............................................................................9

1.6 FS10-R, -RN Unitized Flame Detectors..........................................9

1.6.1 Alert / Early Warning Relay Output ...............................10

1.6.2 Alarm Relay Output.......................................................10

1.6.3 Fault Relay Output.........................................................10

1.6.4 Physical Description......................................................11

1.6.5 Field of View..................................................................11

1.6.6 Environment Range.......................................................11

1.6.7 Location.........................................................................11

1.6.8 Self-Test ........................................................................11

1.6.9 Warranty........................................................................11

SECTION 2: INSTALLATION.......................................................12

2.1 Detector Views ..............................................................................12

2.2 Conduit Installation........................................................................13

2.3 Power Supply Considerations .......................................................14

2.4 Mounting the Flame Detectors ......................................................14

SECTION 3: OPERATING MODES..............................................15

3.1 Normal Operation..........................................................................15

3.2 Alert / Fire Early Warning ..............................................................15

3.3 Alarm Condition.............................................................................15

3.4 Fault Condition ..............................................................................15

3.5 Automatic Detector Test................................................................16

3.6 Manual Detector Test....................................................................16

3.7 Advanced System Diagnostics......................................................16

SECTION 4: MAINTENANCE AND REPLACEMENT..................17

4.1 Detector Faults ..............................................................................17

4.2 Cleaning Detectors Housing Windows..........................................17

4.3 Detector Module Replacement......................................................18

SECTION 5: PINOUT DATA.........................................................19

SECTION 6: ACCESSORIES.......................................................22

6.1 Detector Heavy Duty Swivel Mount (Part No. SM2)......................22

6.2 Test Lamp (Part No. FS-846)........................................................23

6.3 Disposable Protective Covers for Detectors (Part No. DPC-12)..23

6.4 Extension Pole for Disposable Covers (Part No. EXPL-1)............23

6.5 Air Shield for Dirty Applications (Part No. DASA1-P)...................23

6.6 PC Interface Kit (Part No. FS10-IK) ..............................................24

OPERATOR MANUAL // TABLE OF CONTENTS

HONEYWELL 7

Index.............................................................................................25

Limited Warranty.........................................................................26

Contact Honeywell Analytics.....................................................27

Americas.................................................................................................27

Europe ...................................................................................................27

Asia Pacific..............................................................................................27

Internet

...................................................................................................27

Telephone

................................................................................................27

OPERATOR MANUAL // SECTION 1: INTRODUCTION

HONEYWELL 8

SECTION 1: INTRODUCTION

1.1 Application

The Honeywell Analytics Models FS10-R(relay output) are

unitized (stand-alone) Flame Detectors designed specifically for

detecting and alarming to fires in electrostatic powder or paint spray

booths and paint spray lines in industrial and automotive

applications. These multi-spectral, digital, electro-optical, patented

Flame Detectors are housed in explosion proof enclosures and

feature automatic "through-the-lens" self-test. The Detectors may

be ordered with dry contact relays for interfacing to approved

control panels, and either latching or non-latching outputs. FS10-R

Detectors each contain a built-in controller and are unitized

versions of the proven, large installed base FS10 Flame Detectors

with Card Controllers and FS10 Flame Detectors with Wall-

Mounted Controllers.

The FS10 line of Detectors is designed primarily for indoor

fire detection applications where combustible materials exist.

Typical applications include:

-Automotive Paint Lines -Aerosol Filling

-Paint Kitchens -General Finishing

-Curing Ovens -Paint Mixing Rooms

-Powder Coating Booths -Warehouse Storage

-Compressor Modules -Liquid Paint Spray Lines

-Diesel Generators -Internal Storage Tanks

1.2 Responses

The FS10-R type Detectors contain Alert / Fire Early Warning,

Fire Alarm and Fault signal relays. The Alert/Fire Early Warning

and Alarm relays are de-energized, and the Fault relay is energized

1.3 Input Power Requirements

during normal operation. If a fire occurs, a Fire Alarm is declared

in less than 5.0 seconds.

FS10-RTM

1.4 FirePicTM

: The total electrical input power requirement during

normal operation for the Flame Detector is 85 milli-Amps (0.085

Amps) at 24 Volt DC (+/-15%). The maximum current required

during Alarm is 120 milli-Amps.

FirePic stores the sensor data of the last six fire events in the

Detector’s non-volatile digital memory. FirePic provides the

OPERATOR MANUAL // SECTION 1: INTRODUCTION

HONEYWELL 9

numerical spectral evidence to postulate the cause of a fire. The

Detector records the time and date for each FirePic. The FirePic

data includes a graphical display of the relative spectral intensities

versus time preceding and during the fire.

Note

1.5 No Silicone Used

: A PC computer is required to access FirePic.

1.6 FS10-R, -RN Unitized Flame Detectors

silicone based sealant or silicone greases are used in the

Flame Detector.

The multi-spectral digital infrared Flame Detector, spanning the

Wide Band IRTM, Near Band IRTM, and Visible BandTM spectra, has

intelligent, smart computer processing to tell the difference between

a real fire and false alarm radiant energy sources. The Detector

simultaneously

The Detector is factory set for Alert / Fire Early Warning and Fire

Alarm detection range of 15 feet (FS10-R15, -RN15) and 30 feet

(FS10-R30, -RN30) to a one square foot Heptane reference pan

fire. The Alert response time is factory set to 0.3 second, the Fire

Early Warning response time is factory set to 1.0 second, and The

Fire Alarm response time is factory set to less than 5.0 seconds.

The Detectors are factory set for either latching (FS10-R15, -R30)

or non-latching (FS10-RN15, -RN30) as the standard setting.

examines these three spectral radiant energy bands

that are real-time signal processed by an on-board microprocessor.

The Alert / Fire Early Warning response is NOT available

with either the FS10-R45, or FS10-RN45 versions (45 foot

detection range).

The Detector features real-world time and date stamped “Event

History” files that are stored in non-volatile solid-state memory.

OPERATOR MANUAL // SECTION 1: INTRODUCTION

HONEYWELL 10

The Detector performs the following output functions (relay contact

closure or analog current source depending on model utilized):

•Indicates a Fault if trouble occurs.

•Energizes Alert / Fire Early Warning and Fire Alarm if a fire

occurs.

•Turns on the Detector’s LED to indicate Normal Operation, Fire

Alarm, or Fault conditions.

•Communicates externally to a PC desktop or laptop computer

through the built-in RS-485 communication channel, using the

optional “windows” PC Interface Kit (refer to Section 6.6).

1.6.1 Alert / Early Warning Relay Output

The Detector contains one Alert / Fire Early Warning relay with a

contact rating of 1 Amp @ 24 VDC. During Normal Operation the

relay is de-energized with open contacts

1.6.2 Alarm Relay Output

. When an Alert or Fire

Early Warning condition occurs, the relay is energized with closed

contacts.

The Detector contains one Fire Alarm relay with a contact rating of

1 Amp @ 24 VDC. The relay is de-energized with open contacts

during Normal Operation. During a Fire Alarm condition, the relay

is energized with closed contacts.

Note:

1.6.3 Fault Relay Output

The Fire Relay may be ordered configured in a Latching or

Non-Latching mode. If Latching mode is configured, the Fire Relay

will remain energized until the Detector is reset (Powered down and

up). When Non-Latching is configured, the Fire Relay will reset

automatically after 5 seconds. This option is software configured

and must be set in the factory prior to shipment. The standard

factory setting is latching, if an RN version of the Detector is not

ordered.

The Detector contains one Fault relay with a contact rating of 1

Amp @ 24 VDC. The relay is energized during Normal Operation

with closed contacts. When a Fault condition occurs, the relay is

de-energized with opened contacts. Examples of Fault conditions

include loss of power to the Detector or failure of the Self-Test

feature.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Rauchmelder Handbücher

Honeywell

Honeywell TC842B1007AE Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms D350RPL Bedienungsanleitung

Honeywell

Honeywell Gamewell Velociti 3 Series Bedienungsanleitung

Honeywell

Honeywell 5800COMBO Bedienungsanleitung

Honeywell

Honeywell Velociti 3 Series Bedienungsanleitung

Honeywell

Honeywell SS4-A HART Bedienungsanleitung

Honeywell

Honeywell FMST FXV(E) Series Bedienungsanleitung

Honeywell

Honeywell SS4-AI Bedienungsanleitung

Honeywell

Honeywell GENT Venturi-Air Duct Kit Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms SD365R Bedienungsanleitung

Honeywell

Honeywell Notifier NBG-12LX Bedienungsanleitung

Honeywell

Honeywell FCI 1151 Bedienungsanleitung

Honeywell

Honeywell SiXCOMBO Bedienungsanleitung

Honeywell

Honeywell ADEMCO 5806 Bedienungsanleitung

Honeywell

Honeywell X Series Bedienungsanleitung

Honeywell

Honeywell FCI 2151 Bedienungsanleitung

Honeywell

Honeywell SiXSMOKE-CN Bedienungsanleitung

Honeywell

Honeywell compact asd Bedienungsanleitung

Honeywell

Honeywell V-PLEX 5192SD Bedienungsanleitung

Honeywell

Honeywell GasAlert Extreme Bedienungsanleitung

Honeywell

Honeywell ALL-SPEC Bedienungsanleitung

Honeywell

Honeywell DFS8M Bedienungsanleitung

Honeywell

Honeywell SS4-A2 Bedienungsanleitung

Honeywell

Honeywell Notifier FDU-80 Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung