Honeywell Chronotherm IV T8600D Bedienungsanleitung

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1409-1

T8600D Chronotherm® IV

Deluxe Programmable Thermostats

APPLICATION

The T8600 Chronotherm® IV Deluxe Programmable

Thermostat provides electronic control of 24 Vac single-

stage heating and cooling systems.

Refer to Table 1 for a general description of the

thermostat. All T8600 thermostats are powered by either

heating or cooling system.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of properly.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of the old control.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause

a hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

Location

Install the thermostat about 1.5m (5 ft) above the floor in

an area with good air circulation at average temperature.

See Fig. 1.

Do not install the thermostat where it can be affected by:

— drafts, or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

Table 1. Description of T8600 Thermostats

T8600 System Changeover

System

Selection

Fan

Selection Comments

D Heat-Cool Automatic Heat-Off-Cool-

Auto

On-Auto System and fan

selections are done by

keyboard.

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

69-1409—1 2

Wallplate Installation

The thermostat can be mounted horizontally on the wall

or on a 2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

Position wallplate horizontally on the wall or on a

2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

1. Position and level the wallplate (for appearance

only). The thermostat will function correctly even

when not level.

Fig. 1. Typical location of thermostat.

Fig. 2. Mounting the wallplate.

2. Use a pencil to mark the mounting holes. See Fig.

3. Remove the wallplate from the wall and drill two

3/16 inch (76 mm) holes in the wall (if drywall) as

marked. For firmer material such as plaster, drill

two 7/32 inch (5.56 mm) holes. Gently tap anchors

(provided) into the drilled holes until flush with the

wall.

4. Position the wallplate over the holes, pulling wires

through the wiring opening.

5. Loosely insert the mounting screws into the holes.

6. Tighten mounting screws.

WIRING

All wiring must comply with local electrical codes and

ordinances. Refer to Fig. 3 through 5 for typical hookups.

A letter code is located near each terminal for

identification.

CAUTION

Electrical Hazard.

Can cause electrical shock or equipment

damage.

Disconnect power before wiring.

1. Loosen the terminal screws on the wallplate and

connect the system wires. See Fig. 6.

IMPORTANT

Use 18 gauge, color-coded thermostat cable for

proper wiring.

2. Securely tighten each terminal screw.

3. Push excess wire back into the hole.

4. Plug the hole with nonflammable insulation to

prevent drafts from affecting the thermostat.

Fig. 3. Typical hookup in heat only application.

5 FEET

[1.5 METERS]

YES NO

M1010

WIRES

THROUGH WALL

WALL

MOUNTING

HOLES

M15044

MOUNTING

SCREWS

WALL

ANCHORS (2)

(HOT)

M10346A

FAN

RELAY

THERMOSTAT

HEAT

RELAY

RRCW

TRANSFORMER

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

NOT AVAILABLE ON T8600A MODELS.

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

3 69-1409—1

Fig. 4. Typical hookup in heat and cool

system with one transformers

Fig. 5. Typical hookup in heat and cool

system with two transformer.

Fig. 6. Correct wiring technique.

Mounting Thermostat

1. Engage tabs at the top of the thermostat and wall-

plate. See Fig. 7.

2. Press lower edge of case to close and latch.

NOTE: To remove the thermostat from the wall, first pull

out at the bottom of the thermostat; remove top

last.

Fig. 7. Mounting thermostat on wallplate.

(HOT

)

M10347A

FAN

RELAY

THERMOSTAT

HEAT

RELAY

COMPRESSOR

CONTACTOR

TRANSFORMER

HEAT

DAMPER

COOL

DAMPER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT

PUMP SYSTEMS.

AVAILABLE ON SELECT MODELS. OT WIRES MUST HAVE A

SEPARATE CABLE FROM THE THERMOSTAT CABLE.

OTOT

OUTDOOR

TEMPERATURE

SENSOR

(HOT

)

M10348

FAN

RELAY

THERMOSTAT

HEAT

RELAY

(HOT)

COMPRESSOR

CONTACTOR

HEATING

TRANSFORMER

COOLING

TRANSFORMER

HEAT

DAMPER

COOL

DAMPER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

JUMPER RC TERMINAL TO R TERMINAL WHEN INSTALLED ON A

ONE TRANSFORMER SYSTEM.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT

PUMP SYSTEMS.

AVAILABLE ON SELECT MODELS. OT WIRES MUST HAVE A

SEPARATE CABLE FROM THE THERMOSTAT CABLE.

T8600D MODELS REQUIRE POWER TO R TERMINAL AT ALL TIMES.

OTOT

OUTDOOR

TEMPERATURE

SENSOR

M482

OR WRAPAROUND

NSERTION STRIP

/16 IN. (11 MM).

FOR STRAIGHT INSERTION

STRIP 5/16 IN. (8 MM).

M1462

PRESS LOWER

EDGE OF CASE

TO LATCH.

ENGAGE TABS

AT TOP OF

THERMOSTAT

AND WALLPLATE.

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

69-1409—1 4

Using Thermostat Keys

The thermostat keys are used to:

• set current day and time,

• program times and setpoints for heating and cooling,

• temporarily override program temperatures,

• display present setting,

• configure Installer Setup,

• check Self-Test,

• display outdoor temperature (select models),

• set the system operation,

• set the fan operation.

See Fig. 8 for the location of the keys.

Fig. 8. T8600D key locations and descriptions.

SETTINGS

System and Fan Settings

The System default setting is Heat and the Fan default

setting is Auto. Use the System and Fan keys to change

the settings. See Fig. 9. The fan settings can be set for

each program period individually. The system selection is

for all the program periods.

System settings control the thermostat operation as

follows:

Heat: The thermostat controls the heating.

Off: Both the heating and cooling are off.

Cool: The thermostat controls the cooling.

Auto: The thermostat automatically changes between

heating and cooling operation, depending on the

indoor temperature.

Fan settings control the system fan as follows:

On: Fan operates continuously.

Auto: Fan operates with equipment.

Fig. 9. Thermostat System and Fan key locations.

NOTE: Always press the keys with your fingertip or

similar blunt tool. Sharp instruments like a pen

or pencil point can damage the keyboard.

Temperature Settings

Refer to Table 2 for the default program. If the daytime

energy savings period is not used, press the period key

(Leave or Return) until the time is blank. The fan setting

feature is available on select thermostat models. See

Owner’s Guide, form number 69-0940, for complete

instructions on changing the program.

M14624

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time Wake Leave Return Sleep

Day Heat/Cool

Settings

Daylight

Time Copy

INCREASE TEMPERATURE

SETTING OR SCROLL

FORWARD THROUGH

INSTALLER SETUP OPTIONS

DECREASE TEMPERATURE

SETTING OR SCROLL

BACKWARD THROUGH

INSTALLER SETUP OPTION

DISPLAY INFORMATION

SUCH AS PRESENT

SETTINGS AND OUTDOOR

TEMPERATURE

RETURN TO

NORMAL

OPERATIONS

ENTER

INDEFINITE

OR TIMED

HOLD MODE

SET CURRENT

DAY AND TIME

SET CURRENT OR

PROGRAM DAY

CHANGE BETWEEN

DAYLIGHT SAVINGS

AND STANDARD TIME

NCREASE TIME SETTING

R SCROLL FORWARD

HROUGH INSTALLER SETUP

ND SYSTEM TEST

DECREASE TIME SETTING OR

SCROLL BACKWARD THROUGH

INSTALLER SETUP AND SYSTEM TEST

COPY ONE PROGRAMMED

DAY TO ANOTHER DAY

SET WAKE TIMES

AND SETPOINTS

CHANGE BETWEEN

HEATING AND COOLING

SETPOINTS

SET LEAVE TIMES

AND SETPOINTS SET RETURN TIMES

AND SETPOINTS

SET SLEEP TIMES

AND SETPOINTS

SELECT SYSTEM

OPERATION

SELECT FAN

OPERATION

M14625

HoldTemp

Run

Program

Copy

Daylight

Time

Set Current

Day/Time

System Fan

Time Set Program

Day

System

Fan

Wake Leave Return Sleep

Heat/Cool

Settings

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

5 69-1409—1

INSTALLER SETUP

NOTE: For most applications, the thermostat factory

settings will not require changing. Review the

factory settings in Table 2 and if no changes are

necessary, go to the Installer Self-Test section.

The Installer Setup is used to customize the thermostat

to specific systems. Some of the options include

temperature display, system changeover, and outdoor

temperature display. Installer Setup numbers are listed in

Table 3. The table includes all the configuration options

and the factory settings for the T8600.

A combination of key presses is required to use the

Installer Setup feature:

— To enter the Installer Setup, press and hold the

information i key with the increase and

decrease keys until the first number is displayed.

All display segments appear for approximately three

seconds before the number is displayed. See Fig. 10

and 11.

— To advance to the next Installer Setup, press the

Time ∆key.

— To change a setting, use the increase or

decrease  key.

— To scroll the Installer Setup numbers backward, press

the Time ∇key.

— To exit the Installer Setup, press Run Program.

Fig. 10. Display of all LCD segments.

Fig. 11. Display of Installer Setup number and

setting.

CAUTION

Electric Heat System Configuration Hazard.

Can cause equipment damage.

Configure electrical heat system to 1 in Installer

Setup number 2 to prevent system running

without fan.

IMPORTANT

Only configurable numbers are shown on the

device. Example: If thermostat does not have a

System key, Installer Setup Number 12 will not

be displayed. Review Table 3 factory settings

and mark any desired changes in the Actual

Setting column. When Installer Setup is com-

plete, review the settings to confirm that they

match the system.

Table 2. Default Program Settings.

Period Time

Heat

Setpoint

Cool

Setpoint

Fan

Setting

Wake 6:00 AM 70°F

(21°C)

78°F

(25.5°C)

Auto

Leave 8:00 AM 62°F

(16.5°C)

85°F

(29.5°C)

Auto

Return 6:00 PM 70°F

(21°C)

78°F

(25.5°C)

Auto

Sleep 10:00 PM 62°F

(16.5°C)

82°F

(28°C)

Auto

M1455

Aux Ht

Set Day/TimeSet Program

Mon

Wake Leave Return Sleep OutdoorRoom

Filter

Wait System

Fan

Em Hea

Auto

Coo

Auto

Hold for

Heat Cool

Repl Batt

Recovery

DST

TueWedThu Fri Sat Sun

Days

Temporary Setting

Em Ht

M14618

INSTALLER SETUP

NUMBER DISPLAY

(COLUMN 2 OF TABLE 3)

FACTORY SETTING OR OTHER

CHOICE DISPLAY (COLUMN 3

OR 5 OF TABLE 3)

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

69-1409—1 6

Table 3. Thermostat Installer Setup Options.

Select

Installer Setup

Number

(Press Time ∆

key to

change)

Factory Setting

Other Choices

(Press or key to change)

Actual

SettingDisplay Description Display Description

Not used. 1 — — — — —

Fan

operationa.

2 0 Conventional

applications

where equipment

controls fan

operation in heat

mode.

1 Heat pump or electric heat

applications where

thermostat controls fan

operation in heat mode.

Not used. 3 — — — — —

Heating

cycle rate.

4 6 6—6 cph used

for conventional

heat.

1, 3, or

1—1 cph used for radiant

floor heat, gravity

system.

3—3 cph used for hot

water systems or high

efficiency furnaces.

9—9 cph used for electric

heat systems.

Not used. 5 thru 11 — — — — —

System

setting

adjustment

12 1 Manual

changeover

0 or 2 0—Auto changeover.

2—Auto only

Adaptive

Intelligent

Recovery™

control.

13 0 Adaptive

Intelligent

Recovery™

control is

activated (system

starts early so

setpoint is

reached by start

of program

period).

1 Conventional recovery

(system starts recovery at

programmed time).

—

Degree

temperature

display

14 0 Temperature is

displayed in °F

1 Temperature is displayed

in °C

Not used. 15 — — — — —

Clock

format.

16 0 12-hour clock

format.

1 24-hour clock format.

Not used. 17 and 18 — — — — —

Extended

fan operation

in heatinga

19 0 No extended fan

operation after

the call for heat

ends.

1 Fan operation is extended

90 seconds after the call

for heat ends.

Extended

fan operation

in cooling

20 0 No extended fan

operation after

the call for cool

ends.

1 Fan operation is extended

90 seconds after the call

for cool ends.

Not used. 21 thru 23 — — — — —

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

7 69-1409—1

Outdoor

temperature

display

(select

models)

24 0 No outdoor

temperature is

displayed

1 Outdoor temperature is

displayed. Needs a

C70891000 Outdoor

Temperature Sensor to

operate.

Not used. 25 thru 29 — — — — —

Deadband 30 3 Heating and

cooling setpoints

can be set no

closer than 3°F to

(1.5°C).

4 thru

Heating and cooling

setpoints can be set no

closer than the chosen

value:

4—4°F (2°C)

5—5°F (2.5°C)

6—6°F (3°C)

7—7°F (3.5°C)

8—8°F (4°C)

9—9°F (4.5°C)

10—10°F (5°C)

Not used. 31 and 32 — — — — —

Minimum off

time for the

compressor.

33 5 Five-minute

minimum off time

for compressor.

0 thru 4 Minimum number of

minutes (0 thru 5) the

compressor will be off

between calls for the

compressor.

Temperature

range stops

in heating.

34 90 Highest heating

setpoint setting.

40 to 89 Temperature range (1°F

increments) of heating

setpoint settings.

Temperature

range stops

in cooling.

35 45 Lowest cooling

setpoint setting.

46 to 99 Temperature range (1°F

increments) of cooling

setpoint settings/

Not used. 36 — — — — —

Temperature

display

adjustment.

37 0 No difference in

displayed

temperature and

actual room

temperature.

3 thru -3 1—Display adjusts to 1°F

higher than actual

room temperature.

2—Display adjusts to 2°F

higher than actual

room temperature.

3—Display adjusts to 3°F

higher than actual

room temperature.

-1—Display adjusts to 1°F

lower than actual room

temperature.

-2—Display adjusts to 2°F

lower than actual room

temperature.

-3—Display adjusts to 3°F

lower than actual room

temperature.

Furnace air

filter timer.

43 2 30 days (System

run time)

0, 1, 3,

0 – off

1 – 10 days

3 – 60 days

4 – 120 days

(Time is counted when

heat, cool or fan is

running.)

Table 3. Thermostat Installer Setup Options. (Continued)

Select

Installer Setup

Number

(Press Time ∆

key to

change)

Factory Setting

Other Choices

(Press or key to change)

Actual

SettingDisplay Description Display Description

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

69-1409—1 8

IMPORTANT

Review the settings to confirm that they match

the system. Press Run Program to exit the

Installer Setup. The thermostat has saved the

Installer Setup changes and initiated a reset in

order to operate using the new settings. Be sure

to set the current day and time immediately.

Setting Current Day and Time

1. Press Set Current Day/Time.

NOTE: On initial powerup or after an extended power

loss, 1:00 pm flashes on the display until a key

is pressed

2. Press Day until the current day is displayed.

NOTE: Sun=Sunday, Mon=Monday,

Tue=Tuesday, Wed=Wednesday,

Thu=Thursday, Fri=Friday, Sat=Saturday.

3. Press Time ∆or Time ∇until the current time is dis-

played.

NOTE: Tapping the Set Current Day/Time changes the

time in one-hour increments.

NOTE: If the current time is Daylight Savings Time,

press Daylight Time until DST is displayed.

4. Press Run Program.

Viewing or Resetting Timer Settings

When the thermostat activates a timer, the thermostat

flashes Filter until the timer resets.

1. Reset the timer by pressing the ikey until the

expired timer is displayed.

2. Press the time key to reset the timer.

3. Press the Run Program key.

Humidifier

pad monitor.

44 0 Off 1, 2, 3 1 – 90 days

2 – 180 days

3 – 365 days

(Time is counted by

calendar days in heat

mode.)

Ultraviolet air

treatment

(UV) lamp

monitor.

45 0 Off 1 1 – 365 days

(Time is counted by

calendar days in any

mode.)

Table 3. Thermostat Installer Setup Options. (Continued)

Select

Installer Setup

Number

(Press Time ∆

key to

change)

Factory Setting

Other Choices

(Press or key to change)

Actual

SettingDisplay Description Display Description

M1461

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time

Set Current

Day/Time Wake Leave Return Sleep

Day Heat/Cool

Settings

Daylight

Time Copy

Set Day/Time

Mon

M1462

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time Wake Leave Return Sleep

Day

Day Heat/Cool

Settings

Daylight

Time Copy

Set Day/Time

Tue

M1462

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time Wake Leave Return Sleep

Day

Time

Heat/Cool

Settings

Daylight

Time Copy

Set Day/Time

Tue

M1462

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time Wake Leave Return Sleep

Day Heat/Cool

Settings

Daylight

Time

Daylight

Time

Copy

Set Day/Time

DST

Tue

M1462

Time Set Program

System Fan

Run

Program

Run

Program Hold Temp

Set Current

Day/Time Wake Leave Return Sleep

Day Heat/Cool

Settings

Daylight

Time Copy Wake Room

System

Fan

Heat

Auto

DST

Tue

M2024

Filter Days

M2024

Filter Days

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

9 69-1409—1

NOTE: You can view the number of days remaining at

any time by pressing the ikey three or four

times. If more than one timer is active, all active

timers show sequentially when pressing the i

key several times.

INSTALLER SYSTEM TEST

Use the Installer System Test to check the thermostat

operation. Refer to Table 4 for a list of the available

system tests.

CAUTION

Equipment Damage Hazard.

Minimum compressor off-time is bypassed

during Installer System Test.

Avoid cycling compressor quickly.

To start the system test:

Press and hold the increase and decrease keys at

the same time until 10 appears. All segments of the

display are displayed before the 10 appears. See Fig. 12

and 13.

Fig. 12. LCD segments display.

Fig. 13. Test number display.

Refer to Table 5 for the directions and results of the

specific tests.

NOTE: Press Time ∆to advance to the next test and

Time ∇to go back to the previous test. Press

Run Program to exit the system test

Table 4. Tests Available In Installer System Test.

Test

Number System Test Description

10-19 Heating equipment can be turned on and

off.

30-39 Cooling equipment can be turned on and

off.

40-49 Fan equipment can be turned on and off.

60 0 to

60 19

Keyboard keys test.

70-79 Thermostat information, including date

code and software versions, is displayed.

M1455

Aux Ht

Set Day/TimeSet Program

Mon

Wake Leave Return Sleep OutdoorRoom

Filter

Wait System

Fan

Em Hea

Auto

Coo

Auto

Hold for

Heat Cool

Repl Batt

Recovery

DST

TueWedThu Fri Sat Sun

Days

Temporary Setting

Em Ht

M1461

Table 5. Installer System Test Options.

Keys to

Press

Test

Number Description

Heating Equipment System Test

Time ∆10 Enter heating equipment system test.

11 Heat comes on. When Installer Setup number 2 is 1; the system fan is also energized.

10 Heat and system fan turn off.

Cooling Equipment System Test

Time ∆30 Change from heating to cooling equipment system test.

31 Cool and system fan come on.

30 Cool and system fan turn off.

Fan Equipment System Test

Time ∆40 Change from cooling to fan equipment system test.

T8600D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

69-1409—1 10

NOTE: Press any key and the displayed numbers change. Press Time ∇to go to the previous test and Time ∆to go to

the next test. The Run Program key does not exit this test. Press Time ∆or Time ∇and then the Run Program

key to exit.

THERMOSTAT INFORMATION

1. Press the Time ∆key to access the thermostat

information.

2. Press the increase key to display the production

date code. The first two large digits are the month

and the third digit is the last digit of the year

(Example: 027 = February 1997)

3. Press the increase key again to display the soft-

ware identification code. (Example: 02 = software

ID code 2).

4. Press the increase key again to display the soft-

ware revision number (Example: 001 = Revision

number 1).

5. Press the increase key again to display the

EEPROM identification code. (Example: 314 =

EEPROM ID 314).

6. Press the Run Program key to exit the system test.

The system test times out after four minutes with-

out any key presses.

CHECKOUT

Outdoor Temperature Sensor

(Select Models)

Allow the outdoor temperature sensor to absorb the

outdoor air for a minimum of five minutes before taking a

reading.

41 Fan comes on.

40 Fan turns off.

Key Operation System Test

Time ∆60 1 Change from fan to key operation system test.

Table 5. Installer System Test Options. (Continued)

Keys to

Press

Test

Number Description

M1461

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell Y87RFC Bedienungsanleitung

Honeywell

Honeywell Tradeline T8511G Bedienungsanleitung

Honeywell

Honeywell T8600 Bedienungsanleitung

Honeywell

Honeywell DTC 100/2 Bedienungs- und Wartungshandbuch

Honeywell

Honeywell Chronotherm IV T8602D Bedienungsanleitung

Honeywell

Honeywell T8621A Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell T10 Pro Smart Bedienungsanleitung

Honeywell

Honeywell 8160 Bedienungsanleitung

Honeywell

Honeywell TH401 Bedienungsanleitung

Honeywell

Honeywell TRADELINE T8090A Bedienungsanleitung

Honeywell

Honeywell WebStat T7350 Bedienungsanleitung

Honeywell

Honeywell RTH5100B Bedienungsanleitung

Honeywell

Honeywell RCT8100 Bedienungsanleitung

Honeywell

Honeywell TB6575B1000/U - SuitePro Digital Fan Coil... Bedienungsanleitung

Honeywell

Honeywell TL7130A Bedienungsanleitung

Honeywell

Honeywell UtilityPRO Series Bedienungsanleitung

Honeywell

Honeywell TL6120 Bedienungsanleitung

Honeywell

Honeywell T7351 Betriebsanleitung

Honeywell

Honeywell Super Tradeline Q674F Bedienungsanleitung

Honeywell

Honeywell ZSTAT Installationshandbuch

Honeywell

Honeywell CT410A Bedienungsanleitung

Honeywell

Honeywell RTH7460D1018/E 5-1-1 Bedienungsanleitung

Honeywell

Honeywell T3 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung