Honeywell Evohome Bedienungsanleitung

Installation

evohome

Sundial pack

Thermostat

Overview

Honeywell is providing two pre-conﬁgured

packs: Sundial pack and evotouch

Thermostat.

evohome Sundial pack

This pack is suitable for S plan and Yplan

systems with domestic hot water control.

It comprises the following devices that are

necessary to control heating and domestic

hot water:

• Heating relay BDR91

• Domestic hot water relay BDR91

• Domestic hot water sensor CS92A

All devices are pre-conﬁgured with the

evotouch to control heating and domestic

hot water:

evotouch Thermostat

This pack is speciﬁc for a Combi boiler

system without domestic hot water control.

It is already pre-conﬁgured with the BDR91

boiler relay without domestic hot water

control, see “Application 3: Combi boiler” on

page 5.

However, it can be upgraded later on in the

ﬁeld to control domestic hot water as S plan

or Yplan system as well.

To change system conguration:

See “Upgrade application 3: Combi boiler

with domestic hot water” on page 6.

Non pre-congured devices

With non pre-conﬁgured devices such as

HR80UK you can conﬁgure the system by

following the instructions of the GUIDED

CONFIGURATION for all mentioned

applications.

Note: The conﬁguration is dependent on the

application you are selecting.

Components

The CS92A hot water sensor is wireless,

comprising of a transceiver unit and a

strap-on sensor with 1.5 m of cable. It

operates on 2 x AA alkaline batteries, giving

a battery life of at least 2years under typical

operating conditions.

The BDR91 relay module is a wireless relay

module with change over contact 5 A and

transceiver 868 MHz.

ENGLISH

Installation overview

Application 1: Sundial S plan system

Sundial S plan wiring plan

evotouch

DHW Cylinder

V4043

Junction

Box

Boiler

Pump

Radiators

V4043

DHW Heating

L N

230V

50Hz

3A RATED

BROWN

ORANGE

G/YELLOW

BOILER

EN L

PUMP

1 2 3 4 5 6 7 8 9 10

RECEIVER

BDR91

N A B

G/YELLOW

RECEIVER

BDR91

N A B

G/YELLOW

V4043H

ZONE VALVE

HTG

V4043H

ZONE VALVE

MOTOR

GREY

BROWN

BLUE

MOTOR

HTG DHW

NOTE:

1. It is recommended that

either the 10 way junction

box or Sundial Wiring Centre

should be used to ensure

first time, fault free wiring.

2. If using the V4043H1080

(1” BSP) or V4043H1106

(28mm), the white wire must

be electrically isolated.

Pump overrun

S Plan with pump overrun, evotouch controller and two BDR91 relays

BOILER

EN L

PUMP

7 8 9 10

Whilst Honeywell takes all reasonably practicable steps to design and manufacture its products to comply with the requirements of the Health and Safety at Work Act 1974, all products must be properly used and

purchasers are reminded that their obligations under the Act are to ensure that the installation and operation of such products at a place of work should be safe and without risk to them.

These wiring diagrams are for guidance only and at the time of printing represent the latest information available to us from other manufacturers. Honeywell reserve the right at any time and without notice to change

any product, specification or any other information contained in this publication and cannot accept responsibility for loss or damage arising out of any errors that may inadvertently be contained herein.

EN1H - 2111 UK01 R0510

EVOTOUCH

CONTROLLER

CS92A

CYLINDER

THERMOSTAT

20589 S Plan Evo_20589 S Plan Evo 12/05/2010 13:51 Page 1

Application 2: Sundial Y plan system

Sundial Y plan wiring plan

evotouch DHW Heating

DHW Cylinder

Junction

Box

Boiler

Pump

Radiators

V4073

L N

230V

50Hz

3A RATED

BOILER

EN L

PUMP

1 2 3 4 5 6 7 8 9 10

RECEIVER

BDR91

N A B

RECEIVER

BDR91

N A B

GREY

WHITE

ORANGE

BLUE

G/YELLOW

V4073A

MID POSITION

ZONE VALVE

HTG DHW

NOTE:

It is recommended that

either the 10 way junction

box or Sundial Wiring Centre

should be used to ensure

first time, fault free wiring.

Y Plan with pump overrun, evotouch controller and BDR91 receiver

Pump overrun

BOILER

EN L

PUMP

7 8 9 10

and purchasers are reminded that their obligations under the Act are to ensure that the installation and operation of such products at a place of work should be safe and without risk to them.

EN1H - 2112 UK01 R0510

EVOTOUCH

CONTROLLER

CS92A

CYLINDER

THERMOSTAT

20589 Y Plan Evo_20589 Y Plan Evo 15/06/2010 12:28 Page 1

ENGLISH

Application 3: Combi boiler

Combi boiler wiring plan

evotouch

Boiler

Pump

Radiators

L N

230V

50Hz

3A RATED

LE N T1 T2

RECEIVER

BDR91

N A B

Combination boiler with evotouch wireless thermostat

purchasers are reminded that their obligations under the Act are to ensure that the installation and operation of such products at a place of work should be safe and without risk to them.

EN1H - 2113 UK01 R0510

COMBINATION

BOILER

COMBINATION

BOILER

NOTE:

1. It is recommended that

either the 10 way junction

box or Sundial Wiring Centre

should be used to ensure

first time, fault free wiring.

L N

230V

50Hz

3A RATED

LE N T1 T2

RECEIVER

BDR91

N A B

1 2 3 4 5 6 7 8 9 10

EVOTOUCH

CONTROLLER

EVOTOUCH

CONTROLLER

20589 Combi Evo_20589 Combi Evo 12/05/2010 14:00 Page 1

Upgrade application 3: Combi

boiler with domestic hot water

The application Combi boiler can be

upgraded to control domestic hot water as

an Splan or Yplan system by installing the

relay modules for both hot water and heating

control and additionally the hot water sensor

CS92A.

However, the conﬁgured BDR91 boiler relay

must be disconnected from the evotouch to

be used as hot water relay or heating relay.

The following steps must be done to

upgrade the Combi boiler application into a

S plan or Y plan application

1. Uninstall pre-congured BDR91

boiler relay

• Press the evotouch MENU button for

approx. 10seconds.

• Go to menu EDIT SYSTEM CONFIG.

• Select BOILER DEMAND.

• Press the button NONE.

• Reset BDR91 boiler relay.

Note: Press and hold the test button of the

BDR91 boiler relay for 15 seconds until

the red LED ﬂashes 0.9soff / 0.1son. This

ensures that the conﬁguration information

held in the BDR91 boiler relay is removed.

The BDR91 boiler relay is now uninstalled

and can be conﬁgured as hot water relay or

heating relay.

2. Congure S plan or Y plan

system

• Press the evotouch MENU button for

approx. 10seconds.

• Go to menu EDIT SYSTEM CONFIG.

• Select HOT WATER DEMAND.

• Select option HOT WATER DEMAND.

• Bind the hot water sensor CS92A to

evotouch.

• Bind the BDR91 hot water relay.

• Bind the BDR91 heating relay.

...

ENGLISH

Caution

Isolate power supply and make safe before

wiring the units to prevent electric shock and

equipment damage.

Installation should be carried out by a

competent person.

EMC compliance considerations

Keep AC mains supply/load cables separate

from signal wiring. Refer to Code of Practice

standards EN61000-5-1 and EN61000-5-2

for guidance.

Locating CS92A and BDR91 units

The CS92A transceiver and BDR91 relay

module should be mounted in a location

where there are no metal objects in a direct

line between them and the evotouch.

• Do not mount on metal wall-boxes.

• Leave at least 30cm distance from any

metal objects and at least 1 metre from

any other electrical equipment.

• For the CS92A transceiver select a

preferred location, ensuring it is close

enough to the cylinder so that the

strap-on sensor element can reach the

cylinder and test the signal strength

before installation.

Mounting CS92A sensor

The sensor should be mounted on the

cylinder in a position between 1/4 and 1/3 of

the way from the bottom.

• Remove a section of insulation (1) and

clean the exposed cylinder surface

carefully to ensure good thermal contact.

• Position the sensor in the cutout.

• Cut ﬁxing strap (2) to size (if required)

to ensure sensor is held ﬁrmly against

cylinder.

• Locate mounting strap in the cover slot

(3).

• Screw hooks into strap and link together.

Mounting CS92ASafety notes

Mounting CS92A transceiver

The CS92A transceiver is supplied in

the package with the mounting plate

separated from the rest of the unit for ease

of installation.

The sensor wiring can be fed in from the top

of the mounting plate or from the left hand

side.

• Cut a suitable hole in the appropriate

plastic breakout.

• Install the CS92A transceiver mounting

plate in the chosen location next to the

hot water cylinder.

Wiring the CS92A transceiver

• Lead the 2 sensor wires through the

mounting plate and connect them

to terminals A and B on the CS92A

mounting plate as shown. The wires are

polarity free, so they can be connected in

any order.

• Provide appropriate strain relief by

attaching the sensor cable to the wall

using cable clips, or alternatively run the

cable in mini trunking.

Powering up CS92A / Battery

replacement

• First hold the transceiver approximately

1metre from evotouch.

• To power it up, unclip the battery cover,

remove the paper tab that isolates the

batteries from their contacts, and replace

the battery cover.

• When replacing batteries note the battery

polarity.

Closing CS92A transceiver

• Hinge the front piece of the CS92A

transceiver onto the mounting plate and

press until it clicks securely into place.

ENGLISH

Mounting BDR91

• Open the BDR91 relay module by

inserting a screwdriver in the opening at

the bottom.

The wiring can be led in either from the rear

or from the left hand side.

< 7mm

> 7mm

• If entry from the left hand side is desired,

cut suitable holes in the appropriate

plastic breakouts.

= M3.5

= N 6

• Install the BDR91 relay module mounting

plate in the chosen location.

Wiring the BDR91 relay module

• Connect the wires of the power supply

and the boiler/valve control to the

terminals on the BDR91 mounting plate

according to the selected application

(see application diagrams).

Closing BDR91 relay module

• Hinge the front piece of the BDR91 relay

module onto the mounting plate and

press until it clicks securely into place.

Mounting BDR91

How to bind CS92A to evotouch

• Hold the CS92A transceiver

(without mounting plate and sensor)

approximately 1metre from evotouch.

Green light

(under button)

Red light

(under button)

• Put CS92A into binding mode by

pressing and holding the CS92A button

for 5 seconds, until the green light comes

on and the red light ﬂashes once a

second.

• Follow the evotouch GUIDED

CONFIGURATION or EXPERT

CONFIGURATION until the following

screen appears.

• Now press the CS92A button to send the

binding message to evotouch.

• The evotouch display shows “The BIND

signal was received properly. Press

NEXT when successful or BACK to send

again.”.

• If binding was successful CS92A will exit

binding mode and both lights will switch

off.

• If binding was unsuccessful, repeat

binding procedure.

CS92A signal strength test

Once CS92A is bound to evotouch, the

signal strength test allows the transceiver to

be positioned in the best possible location

for signal reception.

Activate signal strength test on the

CS92A transceiver

Green light

(under button)

Red light

(under button)

• Press the CS92A button once.

• The green light should come on. If it

doesn’t, reinsert the batteries and try

again.

• With the green light on, the red light

should start to ﬂash to indicate the status.

Signal Strength = 5

5 secs

Signal Strength = 2

evotouch measures the strength of the

CS92A signal every 5 seconds and will

communicate this to CS92A as a number

between 0 and 5. CS92A will then indicate

this number by ﬂashing its red light a

number of times in succession, followed by

a pause of between 2 and 4 seconds. The

number of ﬂashes is equivalent to the signal

strength number.

A signal strength > 2 is recommended to

ensure reliable communication.

Conﬁguring CS92A

Andere Handbücher für Evohome

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell smartfit Bedienungsanleitung

Honeywell

Honeywell T410A Bedienungsanleitung

Honeywell

Honeywell T8611G Chmnothern IV Bedienungsanleitung

Honeywell

Honeywell T8602C Bedienungsanleitung

Honeywell

Honeywell Chronotherm IV T8611G Bedienungsanleitung

Honeywell

Honeywell T87M2036 Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5000 Series Bedienungsanleitung

Honeywell

Honeywell RTH2310B Bedienungsanleitung

Honeywell

Honeywell RLV430 Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell 2450A Series Bedienungsanleitung

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell Round CT87A Bedienungsanleitung

Honeywell

Honeywell T8635L1013 - MicroElectric Communicating... Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell Q7300A Bedienungsanleitung

Honeywell

Honeywell Chronotherm CM67 Bedienungsanleitung

Honeywell

Honeywell CM727 Bedienungsanleitung

Honeywell

Honeywell CAMIR-8EZS Bedienungsanleitung

Honeywell

Honeywell TL8230A Bedienungsanleitung

Honeywell

Honeywell T8600 Bedienungsanleitung

Honeywell

Honeywell MultiPRO TB7100A1000/U Bedienungsanleitung

Honeywell

Honeywell INNCOM E529 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung