Honeywell FocusPRO TH5110D Bedienungsanleitung

FocusPROTM TH5000 Series

Non-Programmable Digital Thermostat

® U.S. Registered Trademark. Patents pending.

Installation

Guide

Must be installed by a trained, experienced technician

Read these instructions carefully. Failure to follow these instructions

can damage the product or cause a hazardous condition.

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

69-1922EF

This manual covers the following models

• TH5110D: For 1 Heat/1 Cool systems

• TH5220D: For up to 2 Heat/2 Cool systems

(Remove battery holder to find model number)

System Types

• Gas, oil, or electric heat with air

conditioning

• Warm air, hot water, high-

efficiency furnaces, heat pumps,

steam, gravity

• Heat only — two-wire systems,

three-wire zone valves (Series

20), and normally open zone

valves

• Heat only with fan

• Cool only

• 750 mV heating systems

OBSOLETE

Installation Guide

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

Drill 3/16” holes for drywall. Drill 7/32” holes for plaster.

Wall anchors

Wallplate

Wire hole Mounting screws

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Pull here to remove wallplate

from new thermostat.

Remove battery holder.

It's easier to grasp the wallplate

and remove it after completely

removing the battery holder.

OBSOLETE

FocusPROTM TH5110 / TH5220

Power options

Keep wires in this

shaded area

Connect Cfor primary AC power

(optional if batteries are installed).

Insert batteries for primary

or backup power.

Remove factory-

installed jumper

only for two-

transformer

systems.

Conventional Terminals:

Rc 24VAC power from cooling

transformer

R 24VAC power from heating

transformer

W Heat relay (stage 1)

W2 Heat relay (stage 2)

Y Compressor contactor (stage 1)

Y2 Compressor contactor (stage 2)

G Fan relay

C 24VAC common. For 2 transformer

systems, use common wire from

cooling transformer.

Heat Pump Terminals:

Rc 24VAC power from cooling

transformer

R 24VAC power from heating

transformer

O/B Changeover valve

Y Compressor contactor

G Fan relay

Aux Auxiliary heat relay

E Emergency heat relay

L Sends output when set to Em. Heat

C 24VAC common

Wiring

Terminal designations

Shaded areas below apply only to TH5220D.

TH5110D Rc

O/B

TH5220D

RcYWGW2Y2 RC RcYGAuxEL RC

TH5220D

TH5320U

RcYWGW2Y2 RC RcYGAux

Y2L RC

TH5320U

TH5110D Rc

O/B

TH5220D

RcYWGW2Y2 RC RcYGAuxEL RC

TH5220D

TH5320U

RcYWGW2Y2 RC RcYGAux

Y2L RC

TH5320U

OBSOLETE

Installation Guide

Wiring

Wiring guide — conventional systems

Shaded areas below apply only to TH5220D.

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means

and overload protection as required.

[2] Remove jumper for 2-transformer systems.

[3] Optional 24VAC common connection.

[4] Common connection must come from

cooling transformer.

[5] In Installer Setup, set system type to

Heat Only.

[6] In Installer Setup, set system type to

2Heat/2Cool Conventional.

[7] In Installer Setup, set changeover valve to

O or B.

[8] In Installer Setup, set system type to

2Heat/1Cool Heat Pump.

[9] L terminal sends a continuous output when

thermostat is set to Em. Heat. Connect

to Honeywell zoning panels to switch the

panel to Emergency Heat.

[10] Install field jumper between Aux and E if

there is no emergency heat relay.

1H/1C System

(1 transformer)

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

W Heat relay

G Fan relay

Heat-only System

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common [3]

W Heat relay

Heat-only System

(Series 20) [5]

Rc [R+Rc joined by jumper]

R Series 20 valve terminal “R” [1]

Y Series 20 valve terminal “W”

C 24VAC common [3]

W Series 20 valve terminal “B”

Heat-only System

(normally open zone valve) [5]

Rc [R+Rc joined by jumper]

R Power [1]

Y Normally open zone valve

C 24VAC common [3]

1H/1C System

(2 transformers)

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor

C 24VAC common [3, 4]

W Heat relay

G Fan relay

Heat-only System

with Fan

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common [3]

W Heat relay

G Fan relay

Cool-only System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

G Fan relay

2H/2C System

(1 transformer) [6]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common [3]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers) [6]

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor (stage 1)

C 24VAC common [3, 4]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

See [notes] below

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

RcW RC

RcYWGW2Y2 RC

RcYG RC

RcYWG RC RcWG RC

RcYWG RC

RcYW RC

RcY RC

OBSOLETE

FocusPROTM TH5110 / TH5220

Wiring

Wiring guide — heat pump systems

Shaded areas below apply only to TH5220D.

Thermostat mounting

Align the 4 tabs on the wallplate with

slots on the back of the thermostat,

then push gently until the thermostat

snaps in place.

Push excess wire back into

the wall opening.

Plug wall opening with

non-flammable insulation.

1H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

2H/1C Heat

Pump System [8]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux Auxiliary heat relay [10]

E Emergency heat relay [10]

L Sends output when set to Em. Heat [9]

See [notes] on page 4.

RcYG RC

RcYGAuxEL RC

RcYGAux

L RC

RcYGY2

RcYGAux

L RC

RcYG RC

RcYGAuxEL RC

RcYGAux

L RC

RcYGY2

RcYGAux

L RC

OBSOLETE

Installation Guide

To begin, press and hold the sand FAN

buttons until the display changes.

Function

number Setting

Press s or t to change settings.

Press NEXT to advance to the next function.

Press DONE to exit and save settings.

Done Next

Installer setup

Follow the procedure below to configure the thermostat to match the installed

heating/cooling system, and customize feature operation as desired.

Continued on next page

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH5220D.

*[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

1System type 0 1 heat/1 cool conventional

1 1 heat/1 cool heat pump (no aux. heat)

2 Heat only — 2-wire systems, 3-wire zone valves (Series 20), and

normally open zone valves

3 Heat only with fan

4 Cool only

5 2 heat/1 cool heat pump (with aux. heat)

6 2 heat/2 cool conventional

7 2 heat/1 cool conventional

8 1 heat/2 cool conventional

2Changeover valve

(O/B terminal)

0 Changeover valve (O/B terminal energized in cooling)

1 Changeover valve (O/B terminal energized in heating)

3Fan control

(heating)

0 Gas or oil furnace — equipment controls fan in heating

1 Electric furnace — thermostat controls fan in heating

5Stage 1 heat cycle

rate (CPH: cycles/hour)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

6Stage 2 heat cycle

rate/Auxiliary heat

cycle rate (CPH)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

8Emergency heat cycle

rate (CPH)*

9 For electric emergency heat

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

5 For gas or oil furnaces of less than 90% efficiency

OBSOLETE

FocusPROTM TH5110 / TH5220

System test System status

Shaded areas below apply only to TH5220D.

Press s / t to turn system on/off.

Press NEXT to advance to next test.

Press DONE to terminate system test.

Test number System status

10 0

To begin, press and hold the s and t

buttons until the display changes

Installer setup

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH5220D.

CAUTION: Compressor protection is bypassed during testing. To prevent equipment

damage, avoid cycling the compressor quickly

10 Heating system 0 Heat and fan turn off.

1 Stage 1 heat turns on. Fan turns on if Setup Function 1 is set to 1

or 5 OR Setup Function 3 is set to 1 **See page 6

2 Stage 2 heat turns on

20 Emergency heating

system

0 Heat and fan turn off

1 Heat and fan turn on

2 Stage 2 heat turns on (auxiliary heat)

30 Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Stage 2 compressor turns on

40 Fan system 0 Fan turns off

1 Fan turns on

9Stage 1 compressor

cycle rate (CPH)

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

10 Stage 2 compressor

cycle rate (CPH)

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

12 Manual/Auto

changeover

0 Manual changeover (Heat/Cool/Off)

1 Auto changeover (Heat/Cool/Auto/Off)

2 Auto changeover only (Auto)

14 Temperature

display

0 Fahrenheit

1 Celsius

15 Compressor

protection

5 Five-minute compressor off time

[Other options: 0, 1, 2, 3 or 4-minute off time]

26 Auxiliary heat control 0 Comfort **See page 8

1 Economy

27 Heat temperature

range stops

90 Max. heat temperature setting is 90 °F (32 °C)

[Other options: 40 °F to 89 °F (4.5 °C to 31.5 °C)]

28 Cool temperature

range stops

50 Min. cool temperature setting is 50 °F (10 °C)

[Other options: 51 °F to 99 °F (10.5 °C to 37 °C)]

Installer system test

OBSOLETE

Installation Guide

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

http://yourhome.honeywell.com

Automation and Control Solutions

® U.S. Registered Trademark.

69-1922EF M.S. 03-06

Honeywell Limited-Honeywell Limitée

35 Dynamic Drive

Scarborough, Ontario M1V 4Z9

Printed in U.S.A. on recycled

paper containing at least 10%

post-consumer paper fibers.

Special function

Auxiliary heat control (Setup Function 26):

• Comfort Setting: The thermostat will prioritize comfort over economy depending on heat

pump performance, load conditions and whether the thermostat is calling for the heat

pump. Raising the temperature just a few degrees will often activate the auxiliary heat.

• Economy Setting: The thermostat will attempt to reach the temperature setting

without activating the auxiliary heat. The thermostat will wait to activate the auxiliary

heat depending on heat pump performance, load conditions and how many degrees the

temperature setting is changed.

Accessories & replacement parts

Please contact your distributor to order replacement parts.

Part Description Part Number Use With

Battery holder 50000951-001 TH5110D

Battery holder 50007072-001 TH5220D

Cover plate assembly* 50001137-001 TH5110D

Cover plate assembly* 50002883-001 TH5220D/TH5110D

12 pack of small cover plates* 50007297-001 TH5110D

12 pack of medium cover plates* 50007298-001 TH5220D/TH5110D

*Use to cover marks left by old thermostats.

Specifications

Temperature Ranges

• Heat: 40° to 90°F (4.5° to 32°C)

• Cool: 50° to 99°F (10° to 37°C)

Operating Ambient Temperature

• 32° to 120°F (0° to 48.9°C)

Shipping Temperature

• -20° to 120°F (-28.9° to 48.9°C)

Operating Relative Humidity

• 5% to 90% (non-condensing)

Physical Dimensions

TH5220D

• 3-9/16” H x 5-13/16” W x 1-1/2” D

91 mm H x 147 mm W x 38 mm D

TH5110D

• 3-7/16” H x 4-1/2” W x 1-5/16” D

86 mm H x 114 mm W x 33 mm D

Electrical Ratings

Terminal Voltage (50/60Hz) Running Current

WHeating 20-30 Vac 0.02-1.0 A

(Powerpile) 750 mV DC 100 mA DC

W2 (Aux) Heating 20-30 Vac 0.02-0.5 A

YCooling 20-30 Vac 0.02-1.0 A

Y2 Cooling 20-30 Vac 0.02-1.0 A

GFan 20-30 Vac 0.02-0.5 A

O/B Changeover 20-30 Vac 0.02-0.5 A

EEmergency heat 20-30 Vac 0.02-1.0 A

LOutput 20-30 Vac 0.02-0.5 A

OBSOLETE

FocusPROMC Série TH5000

Thermostat numérique non programmable

® Marque de commerce déposée aux É.-U. Brevets en instance.

Guide

d’installation

Doit être installé par un technicien expérimenté et qualifié.

Lire attentivement ces instructions. Le manquement à suivre ces instructions

peut entraîner des dommages au produit et causer des conditions dangereuses.

Besoin d’aide?

Pour obtenir de l’assistance au sujet de ce produit,

consulter le http://yourhome.honeywell.com ou téléphoner sans frais

au Centre de service à la clientèle de Honeywell au 1-800-468-1502

69-1922EF

Ce guide couvre les modèles suivants :

• TH5110D : Pour 1 système de chauffage et 1 système de climatisation

• TH5220D : Pour 2 systèmes de chauffage et 2 systèmes de climatisation

(Enlever le porte-pile pour trouver le numéro de modèle.)

Types de système

• Chauffage au gaz naturel,

au mazout ou à l’électricité

avec climatiseur

• Fournaises à grand rendement

à air chaud ou à eau chaude ;

thermopompes, systèmes

à la vapeur ou gravitaires

• Chauffage seulement – systèmes

à deux fils, soupapes de zone

à trois fils (Série 20) soupapes

de zones normalement ouvertes

• Chauffage seulement avec

soufflante

• Climatisation seulement

• Systèmes de chauffage de 750 mV

OBSOLETE

Guide d’installation

Installation de la plaque murale

1. Séparer la plaque murale du thermostat.

2. Installer la plaque murale tel que décrit

ci-dessous.

Percer des trous de 5 mm (3/16 po)

dans le placoplâtre.

Ancrages muraux

Plaque murale

Trou du fil Vis de montage

MISE EN GARDE : RISQUE DE CHOC ÉLECTRIQUE

Peut causer un choc électrique ou endommager l’équipement. Couper l’alimentation

avant de commencer l’installation.

REMARQUE À PROPOS DU MERCURE :

Si ce produit sert à remplacer une commande qui contient du mercure dans un tube

scellé, ne pas jeter la vieille commande aux ordures. Consulter l’administration locale

de gestion des déchets pour connaître les instructions relatives au recyclage

et à l’élimination.

Tirer ici pour enlever la plaque

murale du thermostat neuf.

Retirer le porte-pile.

Il est plus facile de saisir la

plaque murale et de l’enlever

après avoir complètement

retiré le porte-pile.

Percer des trous de 5,5 mm

(7/32 po) si le mur est en plâtre.

OBSOLETE

Andere Handbücher für FocusPRO TH5110D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell CHRONOTHERM T8624C Bedienungsanleitung

Honeywell

Honeywell T410A Bedienungsanleitung

Honeywell

Honeywell RTH7400 series Bedienungsanleitung

Honeywell

Honeywell Chronotherm CM31 Bedienungsanleitung

Honeywell

Honeywell TRADELINE T834C1137 Bedienungsanleitung

Honeywell

Honeywell T8501D Bedienungsanleitung

Honeywell

Honeywell TH6220WF2 Bedienungsanleitung

Honeywell

Honeywell 36 Bedienungsanleitung

Honeywell

Honeywell T921A Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell CMT927 Bedienungsanleitung

Honeywell

Honeywell TH9000 Series Bedienungsanleitung

Honeywell

Honeywell Lyric T5 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell TRADELINE T8011R Bedienungsanleitung

Honeywell

Honeywell T8665A Chronotherm IV Bedienungsanleitung

Honeywell

Honeywell RTH1120B Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8000 Series Bedienungsanleitung

Honeywell

Honeywell th511od Bedienungsanleitung

Honeywell

Honeywell T4 Pro Bedienungsanleitung

Honeywell

Honeywell RTH2300B Bedienungsanleitung

Honeywell

Honeywell DTS92A Bedienungsanleitung

Honeywell

Honeywell T8611G Chmnothern IV Bedienungsanleitung

Honeywell

Honeywell SimpleSaver Bedienungsanleitung

Honeywell

Honeywell VVT Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung