Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

FocusPRO®Wi-Fi TH6000 Series

Programmable Thermostat

Installation

Guide

Must be installed by a trained, experienced technician

Read these instructions carefully. Failure to follow these instructions

can damage the product or cause a hazardous condition.

Need Help?

For assistance with this product please visit http://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

® U.S. Registered Trademark. Patents pending.

This manual covers the following models

• TH6320WF: For up to 3 Heat/2 Cool systems

System Types

• Gas, oil, or electric heat with air

conditioning

• Warm air, hot water, high-efficiency

furnaces, heat pumps, steam, gravity

• Heat only with fan

• Cool only

69-2738EFS—03 2

MCR29435

M29433

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

Drill 3/16" holes for drywall. Drill 7/32" holes for plaster.

Wall anchors

Wallplate

Wire hole Mounting screws

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do

not place the old control in the trash. Contact your local waste management

authority for instructions regarding recycling and proper disposal.

Insert reference card after wallplate is

mounted (see instructions, below).

MCR29434

3 69-2738EFS—03

Wiring

Wiring guide — conventional systems

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means and

overload protection as required.

[2] Remove jumper for 2-transformer systems.

[4] Common connection must come from cooling

transformer.

[5] In Installer Setup, set system type to Heat Only.

[6] In Installer Setup, set system type to

2Heat/2Cool Conventional.

[7] In Installer Setup, set changeover valve to O

or B.

[8] In Installer Setup, set system type to

2Heat/1Cool Heat Pump.

[9] In Installer Setup, set system type to

2Heat/2Cool Heat Pump.

[10] In Installer Setup, set system type to

3Heat/2Cool Heat Pump.

1H/1C System

(1 transformer)

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common

W Heat relay

G Fan relay

Heat-only System

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common

W Heat relay

1H/1C System

(2 transformers)

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor

C 24VAC common [4]

W Heat relay

G Fan relay

Heat-only System

with Fan

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common

W Heat relay

G Fan relay

Cool-only System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common

G Fan relay

2H/2C System

(1 transformer) [6]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers) [6]

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor (stage 1)

C 24VAC common [4]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

See [notes] below

RcYWG RC

MCR29439

MCR29440

RcWG RC

MCR29444

RcYG RC

MCR29445

RcYWGW2Y2 RC

MCR29446

RcYWG RC

M2944

RcYWGW2Y2 RC

M29447

69-2738EFS—03 4

1H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common

O/B Changeover valve [7]

G Fan relay

2H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

2H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

2H/2C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24 VAC common

O/B Changeover valve [7]

G Fan relay

Y2 Compressor contactor (stage 2)

3H/2C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

Y2 Compressor contactor (stage 2)

See [notes] below

MCR29448

RcY

RcYGAux

MCR29450

RcYGY2

MCR29451

RcYGAux

CY2

MCR29452

RcYGAux

MCR29449A

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means and

overload protection as required.

[2] Remove jumper for 2-transformer systems.

[4] Common connection must come from cooling

transformer.

[5] In Installer Setup, set system type to Heat Only.

[6] In Installer Setup, set system type to

2Heat/2Cool Conventional.

[7] In Installer Setup, set changeover valve to O

or B.

[8] In Installer Setup, set system type to

2Heat/1Cool Heat Pump.

[9] In Installer Setup, set system type to

2Heat/2Cool Heat Pump.

[10] In Installer Setup, set system type to

3Heat/2Cool Heat Pump.

Wiring

Wiring guide — heat pump systems

5 69-2738EFS—03

W2 GWYR RCK Y2 C

MCR33878

HEAT PUMP

CONVENTIONAL

AUX/E GO/B YRRCK Y2 C

Conventional Terminal Letters:

Y2 2nd stage compressor contactor.

W2 2nd stage heat relay.

K Optional wirer save module.

Rc Cooling power. Connect to secondary side

of cooling system transformer.

R Heating power. Connect to secondary side

of heating system transformer.

W 1st stage heat relay.

Y 1st stage compressor contactor.

G Fan relay.

C Common wire from secondary side of

cooling transformer (if 2 transformers).

Heat Pump Terminal Letters:

Y2 2nd stage compressor contactor.

Aux/EAuxiliary/Emergency heat relay.

K Optional wirer save module.

Rc Cooling power. Connect to secondary side

of cooling system transformer.

R Heating power. Connect to secondary side

of heating system transformer.

O/B Changeover valve for heat pumps.

Y 1st stage compressor contactor.

G Fan relay.

C Common wire from secondary side of

cooling system transformer.

Terminal Designations

Wiring

69-2738EFS—03 6

Installer setup

1 Press Fan and s simultaneously and hold for

approximately 3 seconds. The screen will change

to display two numbers and the button designations

will be Done, Back, blank, Next.

2 Press Next until you see the function number—the

larger number on the left—you want to set.

3 Change options for any function by pressing sor

t until the correct option (smaller number on right)

is displayed.

4 Repeat Steps 2 and 3 until you have set all

functions that you wish to change.

5 When you have made all changes, press Done to

save and exit.

MCR33893A

HOLD

MCR33884

HOLD

Function Settings & Options

1Select System

Type

0 Heat/cool: Gas, oil or electric heating with central air conditioning.

1 Heat pump: Heat pump without backup or auxiliary heat.

2 Heat only: Gas, oil or hot water heat without central air conditioning.

3 Heat only with fan: Gas, oil or electric heat without central air

conditioning.

4 Cool only: Central air conditioning only.

5 Heat pump: Heat pump with backup or auxiliary heating.

6 Heat/Cool Multiple stages: 2 heat stages, 2 cooling stages.

7 Heat/Cool Multiple stages: 2 heat stages, 1 cooling stage.

8 Heat/Cool Multiple stages: 1 heat stage, 2 cooling stages.

9 Heat Pump Multiple Stages: 2 heat stages, 2 cool stages.

10 Heat Pump Multiple Stages: 3 heat stages, 2 cool stages.

2Heat Pump

Changeover Valve

(for heat pumps

only)

0 Cooling changeover valve: Use this setting if you connected a wire

labeled “O” to the O/B terminal.

1 Heating changeover valve: Use this setting if you connected a wire

labeled “B” to the O/B terminal.

3Heating Fan

Control

0 Gas or oil heat: Use this setting if you have a gas or oil heating system

(system controls fan operation).

1 Electric heat: Use this setting if you have an electric heating system

(thermostat controls fan operation).

5Heating Cycle

Rate

5 Gas or oil furnace: Standard gas/oil furnace (less than 90% efficiency).

9 Electric furnace: Electric heating systems.

3 Hot water or high-efficiency furnace: Hot water system or gas furnace

(more than 90% efficiency).

1 Gas/oil steam or gravity system: Steam or gravity heat systems.

[Other options: 2,4,6,7,8,10,11,12]

6Heating Cycle

Rate Stage 2

7Heating Cycle Rate

Auxiliary

91st stage compres-

sor cycle rate

3 Recommended for most compressors

[Other options: 1, 2, 4, 5 or 6 CPH]

10 2nd stage com-

pressor cycle rate

7 69-2738EFS—03

System setup

Function Settings & Options

12 Manual/Auto

Changeover

0 Manual changeover (Heat/Cool/Off).

1 Automatic changeover (Heat/Cool/Auto/Off). Automatically turns on Heat

or Cool based on room temperature. Note: System maintains minimum

3°F difference between heat and cool settings.

13 Adaptive Intelligent

Recovery (AIR)

1 On

0 Off

14 Temperature For-

mat (°F/°C)

0 Fahrenheit

1 Celsius

15 Compressor

protection

5 5 minute compressor off time

[Other options: 0, 1, 2, 3 or 4-minute off time]

16 Schedule Options 1 Program schedule is on (7-day programmable).

0 Program schedule is off. Thermostat can not be programmed.

26 Auxiliary Control 0 Comfort

1 Economy

27 Heat temperature

range stop

90 Max. heat temperature setting is 90°F (32°C)

[Other options: 40-89°F (4°C to 32°C)]

28 Cool temperature

range stop

50 Min. cool temperature setting is 50°F (10°C)

[Other options: 51-99°F (11°C to 37°C)]

32 Temperature

display offset

0 Thermostat displays actual room temperature

[Other options: -3, -2, -1, 1, 2, 3°F offset (-1.5°C to 1.5°C)]

36 Device Name

This name will

identify the

thermostat when

you view it remotely.

If you register

multiple thermostats,

give each one a

different name.

52 = Thermostat

1 Basement 16 Exercise Room 30 Library 44 Porch

2 Bathroom 17 Family Room 31 Living Room 45 Rec Room

3 Bathroom 1 18 Fireplace 32 Lower Level 46 Sewing Room

4 Bathroom 2 19 Foyer 33 Master Bath 47 Spa

5 Bathroom 3 20 Game Room 34 Master Bed 48 Storage Room

6 Bedroom 21 Garage 35 Media Room 49 Studio

7 Bedroom 1 22 Great Room 36 Music Room 50 Sun Room

8 Bedroom 2 23 Guest Room 37 Nursery 51 Theater

9 Bedroom 3 24 Gym 38 Office 52 Thermostat

10 Bedroom 4 25 Kid's Room 39 Office 1 53 Upper Level

11 Boat House 26 Kitchen 40 Office 2 54 Utility Room

12 Bonus Room 27 Kitchen 1 41 Pantry 55 Walk In Closet

13 Computer Room 28 Kitchen 2 42 Play Room 56 Wine Cellar

14 Den 29 Laundry Room 43 Pool Room 57 Workshop

15 Dining Room

38 Wi-Fi On/Off 1 Wi-Fi is on and can be connected to a Wi-Fi network.

0 Wi-Fi is off. Thermostat cannot be connected to a Wi-Fi network. If you

are not connecting the thermostat to a Wi-Fi network this will remove the

text Wi-Fi Setup from the messaging center.

39 Wi-Fi Connection 1 Connected to Wi-Fi network. This is set automatically when the

thermostat is connected to the Wi-Fi network.

0 Set to 0 to disconnect from the Wi-Fi network.

42 Show period and

day of week

0 Period and day are not shown on the home screen.

1 Period and day are shown on the home screen.

85 Restore Schedule

Defaults

0 Continue using programmed schedule.

1 Restore thermostat program to energy saving settings

90 Restore Original

Settings

0 No

1 Disconnects thermostat from Wi-Fi and restores original settings (erases

customizations).

69-2738EFS—03 8

10 Heating system 0 Heat and fan turn off.

1 Stage 1 heat turns on. Fan turns on if Setup Function 1 is set to 1,

5, 9 or 10 OR Setup Function 3 is set to 1 **See page 6

2 Stage 2 heat turns on

3 Stage 3 heat turns on

20 Emergency heating

system 0 Heat and fan turn off

1 Heat and fan turn on

30 Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Stage 2 compressor turns on

40 Fan system 0 Fan turns off

1 Fan turns on

Installer system test

10 0

MCR29455

Press s / t to turn system on/off.

Press NEXT to advance to next test.

Press DONE to terminate system

test.

Test number System status

To begin, press and hold the s and

t buttons until the display changes.

CAUTION: Compressor protection is bypassed during testing. To prevent

equipment damage, avoid cycling the compressor quickly.

System test System status

9 69-2738EFS—03

M33998

Troubleshooting

Lost Signal

If the no-Wi-Fi indicator displays in place of the Wi-Fi strength indicator in the upper right

hand corner of the home screen:

• Check another device to be sure Wi-Fi is working in your home; if not, call your

Internet Service Provider.

• Move the router.

• Restart the thermostat: remove it from the wallplate, wait 10 seconds, and snap it

back onto the wallplate. Return to Step 1 of Connecting to your Wi-Fi network.

Error Codes

For certain problems, the thermostat screen will display

a code that identifies the trouble. Initially, error codes are

displayed alone in the time area of the screen; after a

few minutes, the home screen is displayed and the code

alternates with the time.

Error Code Action

E01 During Wi-Fi Setup, the router

lost power.

• Ensureyourrouterhaspower.

• Iftryingtoconnecttoahiddenormanuallyaddednetwork,

confirm the router has power and is working.

E02 Invalid Wi-Fi password. This

code displays for 30 seconds,

then the thermostat will re-enter

Wi-Fi Setup mode.

• Re-enterpasswordforyourhomeWi-Finetwork.

• Repeatsetupprocessandconfirmyourpasswordforyourhome

Wi-Fi network.

E42 Router is not issuing an IP ad-

dress to the thermostat.

• Waitfor30minutes,

connection can take several

minutes.

• Ifstillnoconnection,remove

thermostat from wallplate for

10 seconds, then reconnect it.

• Verifyyourrouteriscorrectly

setup to automatically give IP

addresses.

E43 No internet connection. Thermo-

stat cannot communicate to Total

Connect Comfort.

• MakesuretheInternetcableispluggedin.

• Reboottherouter.

E99 General error Remove thermostat from wallplate for 10 seconds, then reconnect

it.

M33999

69-2738EFS—03 10

Troubleshooting

If you have difficulty with your thermostat, please try the following suggestions.

Most problems can be corrected quickly and easily.

Display is

blank

• Checkcircuitbreakerandresetifnecessary.

• Makesurepowerswitchatheatingandcoolingsystemison.

• Makesurefurnacedoorisclosedsecurely.

• MakesureCwireisconnected.

Fan does

not turn on

when heat is

required

• CheckFunction 3: Heating Fan Control to make sure it is set to match the

heating equipment.

Cool On or Heat

On is flashing

on the screen

• Compressorprotectionfeatureisengaged.Wait5minutesforthesystemto

restart safely, without damage to the compressor.

Heat pump

issues cool air

in heat mode,

or warm air in

cool mode

• CheckFunction 2: Heat Pump Changeover Valve to make sure it is properly

configured for your system.

Heating system

is running in

cool mode

• CheckFunction 1: System Type to make sure it is set to match the heating

and cooling equipment.

Heating

and cooling

equipment are

running at the

same time

• CheckFunction 1: System Type to make sure it is set to match the heating

and cooling equipment.

• Graspandpullthermostatawayfromwallplate.Checktomakesurebare

wires are not touching each other.

• Checkthermostatwiringiscorrect.

Andere Handbücher für FocusPRO Wi-Fi TH6000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell VT15 Bedienungsanleitung

Honeywell

Honeywell CM900 Bedienungsanleitung

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell T87F Montageanleitung

Honeywell

Honeywell T8635L Bedienungsanleitung

Honeywell

Honeywell T8022D Bedienungsanleitung

Honeywell

Honeywell RLV430 Bedienungsanleitung

Honeywell

Honeywell T8624 Bedienungsanleitung

Honeywell

Honeywell RET97B5D Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH6110D Bedienungsanleitung

Honeywell

Honeywell INNCOM e7 Bedienungsanleitung

Honeywell

Honeywell Lutron VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell UtilityPRO Series Bedienungsanleitung

Honeywell

Honeywell THX9000 Prestige HD Benutzerhandbuch

Honeywell

Honeywell VisionPRO TH8321 Bedienungsanleitung

Honeywell

Honeywell PRO TH1100D Bedienungsanleitung

Honeywell

Honeywell ST772 Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung

Honeywell

Honeywell Q682 Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Smart Bedienungsanleitung

Honeywell

Honeywell T8611G Chmnothern IV Bedienungsanleitung

Honeywell

Honeywell T4800A Bedienungsanleitung

Honeywell

Honeywell C Bedienungsanleitung

Honeywell

Honeywell T10 Pro Smart Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung