Honeywell ST772 Bedienungsanleitung

Setting the ON and OFF programme times

Note: The ON and OFF times can be set in 10 minute steps.

If you do not wish to usethe two ON and OFF times, set the

lst OFF time equal to the lst ON time.

If you do not wish to change a particular ON or OFF time

simply move the slider to the next ON or OFF time.

The 2nd OFF time can be setpast midnight up to 2.50am of

thefollowing day.

1 Move the TIME SET slider to the Ist ON time. The display will

now change to show the Ist ON time. The ON time will flash

to indicate it can be changed. The day marker will appear

below MON indicating that you are changing the programme

times for Monday.

.The slider should always be returned to the AUTO position

after setting theprogrammel:

.The CHANGE button function as described under

Using your Programmer is used to temporarily override the

heating or hot water and to alter the time of day or the

programme times when setting up the programmel:

2 Use the + and -buttons to set the required Ist ON time

3 Move the TIME SET slider to the lst OFF time. The OFF time

will flash to indicate it can be changed.

.The programmer is delivered with a factory installed

programme for Hot Water and Heating as detailed below. This

can easily be modified as described later: 4 Use the + and -buttons to set the required Ist OFF time

5 Repeat steps 1 to 4 to set the 2nd ON and OFF times

Built in programme

lst ON lst OFF

6.30am 8.30am 2nd ON

4.30pm

2nd OFF

lO.30pm

6 You can now set the programme times for the next day in two

different ways.

Choice 1

STEP DAY. Press the DAY button to move the day marker to the

next day. The ON OFF times can now be set by following steps

1-5 above. Repeat this process until every day of the week has

been set.

Setting the Correct Time and Day

1 Move the TIME SET slider to the DAY/CLOCK position. The

display will now be flashing to indicate it can be changed.

2 Use the DAY button to change the day indicated to the current

day. Each pressof the DAY button will move the day marker on

one day at a time. Choice 2

3 Use the + and -buttons to set the current time of day, making

surethat the AM/PM symbol is correct. STEP DAY AND COPY. Pressand hold down the DAY button for

at least three seconds.The day marker for the next day will appear

and, at the same time, the current day marker will start to flash to

indicate a copy function is in progress. Repeat this process to copy

the current day's programme into several days of the week

if required.

Note: Pressing and releasing a + or -button changes the time in

oneminute steps.lithe button is held downior aiew seconds,

the time changesmore rapidly.

4 If the programme times are to be changed follow the instructions

below. If not, return the slider to the AUTO position.

2 Red indicator lamps to the left of the CHANGE buttons show

when the heating or hot water is switched ON.

Note: It is possible to mix the above two choices. For example,

Monday to Friday can be set using the STEP DAY AND

COPY procedure and Saturday and Sunday can be set using

the STEP DAY procedure. 3 Choose the operation for heating and hot water from the

following options on the programmer, using the two sliders on

the right hand side of the programmer.

When all required changes have been made, return the slider to

the AUTO position. The heating or hot water is turned completely OFF

Note: CONT The heating or hot water remain ON continuously

If the ST772 has been installed as a Weekday-Weekend

programmer, the day marker will be displayed asablock of days

(Mon...Fri or Sat...Sun) when setting the programme times. The

DAY button will switch between the Weekday and Weekend

programmes when pressed.

TWICE The heating and hot water will turn ON and OFF at each

of the ON and OFF times set.

ONCE The heating or hot water will turn ON at the first ON time

setand stay on until the last OFF time seteach day.

2 Each programme time can be set between 3.00am and 2.50am

(on the next day) to allow you to programme past midnight,

if required. Change

To temporarily override the heating or hot water settings press the

CHANGE button. If the heating or hot water system is ON it will

turn OFF until the next programmed ON time. If OFF it will turn

ON until the next programmed OFF time. To cancelpressthe button

again. Change operatesonly in the TWICE and ONCE modes.

3 Programme times cannot be set out of sequence.If the -button

is being pressed, the time will stop changing when it equals a

previous programme time. If the + button is being pressed,

subsequentprogramme times will be pushed forward along with

the one being set.

Notes

4 If the TIME SET slider is accidentally left in an ON, OFF or

DAY/CLOCK position for a period of 10 minutes, the unit will

start to operate as if it had been left in AUTO. The display will

flash when this occurs to remind you to move the slider to the

correct position.

Pressing the RESET button will completely reset the programme

settings to the factory pre-set times.

Your programmer is fitted with a battery reserve which will sustain

operation of the programmer for a maximum of 12 hours of mains

electricity disconnection.

Reviewing and Changing Programme Times

To review the ON OFF programme times and change them if

required move the TIME SET slider to each of the ON OFF

positions in turn. Pressthe DAY button to selectdifferent days as

required. Any time can be adjusted by using the + or -buttons.

Your programmer is not user serviceable. Do not attempt to

dismantle the unit. In the unlikely event of afault developing in the

unit or with any other part of your heating system contact a

qualified heating installer: However, first try resetting the

programmer asdescribed above.

2 Move the TIME SET slider to the AUTO position to complete

reviewing/changing the programme times.

Honeywell

Using your Programmer Helping YouControl Your WorldHoneywell Control Systems LId

Arlington Business Park

Bracknell

Berkshire RGI2 lEB

Normal Operation RES2449

42008780-002

1 Ensure that the TIME SET slider is in the AUTO position

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell TRADELINE Electronic Thermostat Bedienungsanleitung

Honeywell

Honeywell PRO TH1000 Series Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell VT15 Bedienungsanleitung

Honeywell

Honeywell TRADELINE T8400C Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5220D Bedienungsanleitung

Honeywell

Honeywell Single Stage Heat Pump ProgrammableCommercial... Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell T7351 Betriebsanleitung

Honeywell

Honeywell t7100f Bedienungsanleitung

Honeywell

Honeywell Lyric T5 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell CT50A, CT51A, CT53A Bedienungsanleitung

Honeywell

Honeywell Q682B Bedienungsanleitung

Honeywell

Honeywell T827B Bedienungsanleitung

Honeywell

Honeywell RTH7600 Series Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell T822 Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell RLV310 Bedienungsanleitung

Honeywell

Honeywell TRADELINE T8011R Bedienungsanleitung

Honeywell

Honeywell T834 series Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5000 Series Bedienungsanleitung

Honeywell

Honeywell DMULTISTAGE T8524C Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung