Honeywell Lyric T6 Pro Wi-Fi Bedienungsanleitung

Andere Handbücher für Lyric T6 Pro Wi-Fi

7

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T834C Bedienungsanleitung

Honeywell

Honeywell CM907 Bedienungsanleitung

Honeywell

Honeywell PRO 1000 Series Bedienungsanleitung

Honeywell

Honeywell RTH6400 Series Bedienungsanleitung

Honeywell

Honeywell RTH5100B Bedienungsanleitung

Honeywell

Honeywell CT3611 Benutzerhandbuch

Honeywell

Honeywell LYRIC T4 Montageanleitung

Honeywell

Honeywell CM907 Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell TH115-AF-GA Bedienungsanleitung

Honeywell

Honeywell RTH2300B1038/E1 Bedienungsanleitung

Honeywell

Honeywell TH4210U2002 Bedienungsanleitung

Honeywell

Honeywell PROGRAMMABLE THERMOSTAT RTH6350 Bedienungsanleitung

Honeywell

Honeywell CT2095 Bedienungsanleitung

Honeywell

Honeywell T6R-HW Bedienungsanleitung

Honeywell

Honeywell T827B Bedienungsanleitung

Honeywell

Honeywell TC500A Bedienungsanleitung

Honeywell

Honeywell Chronotherm III T8602A Bedienungsanleitung

Honeywell

Honeywell MagicStat CT3300 Technische Daten

Honeywell

Honeywell T8112C Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell T8000 Handbuch

Honeywell

Honeywell DT70 Series Bedienungsanleitung

Honeywell

Honeywell HH07AT216 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung

Package Includes:

• T6 Pro Thermostat

• UWP™ Mounting System

• Honeywell Standard Installation

Adapter (J-box adapter)

• Honeywell Decorative Cover Plate –

Small; size 449/64 in x 449/64 in x

11/32 in (121 mm x 121 mm x 9 mm)

• Screws and anchors

• 2 AA Batteries

• Installation Instructions and User

Guide

T6 Pro

Programmable Thermostat

Installation Instructions

Optional Cover Plate installation

NOTE: If Optional Cover Plate is not

required, see “UWP Mounting System

installation” on next page.

Use the Optional Cover Plate when:

• Mounting the thermostat to an

electrical junction box

• Or when you need to cover paint gap

from old thermostat.

1. Separate the Junction Box Adapter

from the Cover Plate. See Figure 1.

2. Mount the Junction Box Adapter to

the wall or an electrical box using any

of the eight screw holes. Insert and

tighten mounting screws supplied with

Cover Plate Kit. Do not overtighten. See

Figure 2. Make sure the Adapter Plate

is level.

3. Attach the UWP by hanging it on the

top hook of the Junction Box Adapter

and then snapping the bottom of the

UWP in place. See Figure 3.

4. Snap the Cover Plate onto the Junction

Box Adapter. See Figure 4.

Use 2x

supplied

screws #6

5/8”

4

3

2

1

2

S

S

Y2

U

U

G

C

Y

A

Rc

W

K

W2

R

L/A

O/B

AUX

E

Power options

Insert Rand Cwires into

designated terminals for primary

AC power (C terminal is optional

if batteries are installed, but it is

recommended). Remove wires by

depressing the terminal tabs.

Insert AA batteries for primary or backup

power.

UWP Mounting System installation

Use 3x supplied

screws #8 11/2”

5. Before starting, turn the power off

at the breaker box or switch. Open

package to find the UWP. See Figure 5.

6. Position the UWP on wall. Level and

mark hole positions. See Figure 6.

Drill holes at marked positions, and

then lightly tap supplied wall anchors

into the wall using a hammer.

‒Drill 7/32” holes for drywall.

7. Pull the door open and insert the wires

through wiring hole of the UWP. See

Figure 7.

8. Place the UWP over the wall anchors.

Insert and tighten mounting screws

supplied with the UWP. Do not

overtighten. Tighten until the UWP

no longer moves. Close the door. See

Figure 8.

8

5

6

7

3

Wiring terminal designations

SInput for wired indoor

or outdoor sensors

(TH6320U and

TH6220U only)

L/A

- A

Heat Pump fault input

(Common (C) wire required

for LA/A)

SO/B Changeover valve

YCompressor contactor

(stage 1)

AUX -

W2

Auxiliary heat relay

Heat relay (stage 2)

Y2 Compressor contactor

(stage 2) EEmergency Heat relay

GFan Relay WHeat relay (stage 1)

C

24VAC common. For 2

transformer systems,

use common wire from

cooling transformer.

KConnect to K on Wire Saver

Module**

U

Unused

R24VAC power from heating

transformer*

URc 24VAC power from cooling

transformer*

Note: Not all

terminals may be

used, depending

on the system

type that is being

wired. The most

commonly used

terminals are

shaded.

* Terminal can be jumped using Slider Tab. See “Setting Slider Tabs” above.

** The THP9045A1023 Wire Saver Module is used on heat/cool systems when you

only have four wires at the thermostat, and you need a fifth wire for a common wire.

Use the K terminal in place of the Y and G terminals on conventional or heat pump

systems to provide control of the fan and the compressor through a single wire—the

unused wire then becomes your common wire. See THP9045 instructions for more

information.

Set R Slider Tab.

• Use built-in jumper (R Slider Tab)

to differentiate between one or two

transformer systems.

• If there is only one R wire, and it is

connected to the R, Rc, or RH terminal, set

the slider to the up position (1 wire).

• If there is one wire connected to the R

terminal and one wire connected to the Rc

terminal, set the slider to the down position

(2 wires).

NOTE: Slider Tabs for U terminals should be

left in place for T6 Pro models.

Setting Slider Tabs

R/Rc slider tab

UWP Mounting System

4

1H/1C System (1 transformer)

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

W Heat relay

G Fan relay

Heat-only System

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

C 24VAC common [3]

W Heat relay

Heat-only System (Series 20) [5]

R Series 20 valve terminal “R” [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Series 20 valve terminal “W”

C 24VAC common [3]

W Series 20 valve terminal “B”

Heat-only System

(power open zone valve) [5]

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

W Valve

C 24VAC common [3]

1H/1C System (2 transformers)

R Power (heating transformer) [1]

Rc Power (cooling transformer) [1]

Y Compressor contactor

C 24VAC common [3, 4]

W Heat relay

G Fan relay

Heat-only System with Fan

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

C 24VAC common [3]

W Heat relay

G Fan relay

Cool-only System

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

G Fan relay

2H/2C System (1 transformer) [6]

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor (stage 1)

C 24VAC common [3]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

Wiring conventional systems: forced air and hydronics

Shaded areas below apply only to TH6320U/TH6220U or as otherwise noted.

NOTES

Wire specifications: Use 18 to 22-gauge thermostat wire. Shielded cable is not required.

[1] Power supply. Provide disconnect means and over-

load protection as required.

[2] Move RSlider Tab on UWP to the Rsetting. For

more information, see “Setting Slider Tabs” on page

3

[3] Optional 24VAC common connection.

[4] Common connection must come from cooling

transformer.

[5] In ISU set Heat system type to Radiant Heat. Set

number of cool stages to 0.

[6] In Installer Setup, set system type to 2Heat/2Cool

Conventional.

5

1H/1C Heat Pump System

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

W Do not use this terminal for heat pump

applications!

2H/1C Heat Pump System [8]

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux Auxiliary heat

E Emergency heat relay

L Heat pump fault input

W Do not use this terminal for heat pump

applications!

2H/2C Heat Pump System

(TH6320U only) [9]

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor (stage 1)

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Y2 Compressor contactor (stage 2)

L Heat pump fault input

W Do not use this terminal for heat pump

applications!

3H/2C Heat Pump System

(TH6320U only) [10]

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor (stage 1)

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux Auxiliary heat

E Emergency heat relay

Y2 Compressor contactor (stage 2)

L Heat pump fault input

W Do not use this terminal for heat pump

applications!

Dual Fuel System (TH6320U / TH6220U only)

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor (stage 1)

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux Auxiliary heat

E Emergency heat relay

Y2 Compressor contactor (stage 2 - if

needed) [11]

L Heat pump fault input

S Outdoor sensor

S Outdoor sensor

W Do not use this terminal for heat pump

applications!

Wiring heat pump systems

Shaded areas below apply only to TH6320U/TH6220U or as otherwise noted.

NOTES

Wire specifications: Use 18 to 22-gauge thermostat wire. Shielded cable is not required.

[1] Power supply. Provide disconnect means and over-

load protection as required.

[2] Move RSlider Tab on UWP to the Rsetting. For

more information, see “Setting Slider Tabs” on page

3

[3] Optional 24VAC common connection.

[6] In Installer Setup, set system type to 2Heat/2Cool

Conventional.

[7] In Installer Setup, set changeover valve to O (for

cool changeover) or B (for heat changeover).

[8] In ISU set Heat system type to Heat pump. 1 com-

pressor and 1 stage of backup heat.

[9] In ISU set Heat system type to Heat pump. 2 com-

pressors and 0 stage of backup heat.

[10] In ISU set Heat system type to Heat pump. 2 com-

pressors and 1 stage of backup heat.

[11] Dual fuel with Y2 only for TH6320U.

6

Thermostat mounting

1. Push excess wire back into the wall

opening.

2. Close the UWP door. It should remain

closed without bulging.

3. Align the UWP with the thermostat, and

push gently until the thermostat snaps in

place.

4. Turn the power on at the breaker box or

switch.

Set the time and date

Time

1 Press Menu on your thermostat.

2 Press or to go to TIME. Press Select.

3 Press or to choose between 12 or 24 hour.

Press Select.

4 Use or to adjust the hour. Press Select.

5 Use or to adjust the minutes. Press Select

to exit Time menu.

Date

1 If previously setting time, continue to Step

2. If at the Home screen, press Menu on your

thermostat.

2 Press or to go to DATE. Press Select.

3 Use or to adjust year. Press Select.

4 Use the or to adjust month. Press Select.

5 Use the or to adjust day. Press Select to

save and exit Date menu.

7

Fan operation settings

1 Press the Fan button to cycle to the next

available Fan mode.

2 Cycle through the modes until the required

Fan mode is displayed and leave it to

activate.

NOTE: Available Fan modes vary with system

settings.

Fan modes:

‒Auto: Fan runs only when the heating or

cooling system is on.

‒On: Fan is always on.

‒Circ: Fan runs randomly about 33% of

the time.

System operation settings

1 Press the Mode button to cycle to the next

available System mode.

2 Cycle through the modes until the required

System mode is displayed and leave it to

activate.

NOTE: Available System modes vary by model

and system settings.

System modes:

‒Auto

‒Heat

‒Cool

‒Em Heat

‒Off

Alerts or Reminders*

1 Press Menu, and then press until display

shows ALRT.

2 Press Select to display which alert(s) are

present.

3 The word SNZE (SNOOZE) appears.

4 Press Select again to snooze the reminder

for 7 days.

5 To clear the alert, press Select, and then

press to go to CLER (Clear).

6 Press Select to clear the reminder.

* Some alerts cannot be snoozed or cleared.

Please call your local heating and cooling

professional if this occurs. The heating and

cooling system may require service.

8

1 Press and hold CENTER and buttons for

approximately 3 seconds to enter advanced

menu.

2 Press Select to enter ISU.

3 Press Select to cycle through menu setup

options.

4 Press or to change values or select

from available options.

5 Press Select and confirm your settings or

press Back to ignore changes and return

to ISU menu screen to continue editing

another setup option.

6 To finish setup process and save your

setting, press Home and return to Home

screen.

NOTE: A complete list of all setup (ISU)

parameters and options starts below and

continues through page 10.

Installer setup (ISU)

Advanced setup options (ISU)

NOTE: Depending on system settings, not all options may be available.

# ISU ISU Name ISU Options (factory default in bold)

120 Scheduling Options 0 = NonProgrammable

2 = 52 Programmable

3 = 511 Programmable

4 = 7Day Programmable

125 Temperature Indication Scale 0 = Fahrenheit

1 = Celsius

130 Outdoor Sensor

(TH6320U / TH6220U only) 0 = None

1 = Wired Outdoor Sensor

200 Heating System Type 1 = Conventional Forced Air Heat

2 = Heat Pump

3 = Radiant Heat

5 = None (Cool Only)

205 Heating Equipment Type Conventional Forced Air Heat:

1 = Standard Efficiency Gas Forced Air

2 = High Efficiency Gas Forced Air

3 = Oil Forced Air

4 = Electric Forced Air

5 = Hot Water Fan Coil

Heat Pump:

7 = Air to Air Heat Pump

8 = Geothermal Heat Pump

Radiant Heat:

9 = Hot Water Radiant Heat

12 = Steam

218 Reversing Valve O/B 0 = O (O/B in Cool)

1 = B (O/B in Heat)

220 Cool Stages / Compressor Stages

200=Conv / 200=HP 0, 1, 2

Note: Only 1 compressor stage available on TH6210U model. Only 1 compressor

stage available on TH6220U model if configured for heat pump.

9

# ISU ISU Name ISU Options (factory default in bold)

221 Heat Stages / Backup Heat Stages Heat Stages: 1, 2

Backup Heat Stages: 0, 1

230 Fan Control in Heat 1 = Equipment Controls Fan

2 = Thermostat Controls Fan

253 Aux/E terminal control (Fixed to

“0” setting on all models except

TH6320U)

0 = Drive both Aux & E together

1 = Aux and E independent

255 Backup Heat Source

(Heat Pump Only)

(TH6320U / TH6220U only)

1 = Electric Forced Air

2 = Gas/Oil Forced Air (or Fossil Forced Air)

256 Emergency Heat Source (TH6320U

only) 1 = Electric Forced Air

2 = Gas/Oil Forced Air (or Fossil Forced Air)

260 External Fossil Fuel Kit

(TH6320U / TH6220U only) 0 = Thermostat Controls Backup Heat

1 = External Fossil Fuel Kit Controls Backup Heat

300 System Changeover 0 = Manual

1 = Automatic

303 Auto Changeover Differential 0 °F to 5 °F

0.0 °C to 2.5 °C

Note: Differential is NOT deadband. Honeywell uses an advanced algorithm that

fixes deadband at 0 °F. The differential setting is the minimum number of degrees

from set-point needed to switch from the last mode running (heat or cool) to the

opposite mode when the thermostat is in auto-changeover. This is more advanced

than previous thermostats.

340 Backup Heat Droop 0 = Comfort

2 = 2 °F

3 = 3 °F

4 = 4 °F

5 = 5 °F

6 = 6 °F

7 = 7 °F

8 = 8 °F

9 = 9 °F

10 = 10 °F

11 = 11 °F

12 = 12 °F

13 = 13 °F

14 = 14 °F

15 = 15 °F

Note: 0 (comfort) setting only available if backup heat (ISU 255) is set to electric.

350 Upstage Timer for Backup Heat 0 = Off

1 = 30 minutes

2 = 45 minutes

3 = 60 minutes

4 = 75 minutes

5 = 90 minutes

6 = 2 hours

7 = 3 hours

8 = 4 hours

9 = 5 hours

10 = 6 hours

11 = 8 hours

12 = 10 hours

13 = 12 hours

14 = 14 hours

16 = 16 hours

355 Compressor Lockout / Balance Point -- = Off

5 °F to 60 °F (in 5 °F increments)

15.0 °C to 15.5 °C (in 2.5 °C or 3.0 °C increments)

Note: Use a wired sensor to set compressor lockout / balance point on TH6320U

/ TH6220U.

356 Outdoor Lockout Backup Heat -- = Off

5 °F to 65 °F (in 5 °F increments)

15.0 °C to 18.5 °C (in 2.5 °C or 3.0 °C increments)

365 Compressor Cycle Rate (Stage 1) 1 - 6

366 Compressor Cycle Rate (Stage 1) 1 - 6

370 Heating Cycle Rate (Stage 1) 1 - 12

371 Heating Cycle Rate (Stage 2) 1 - 12

375 Heating Cycle Rate Auxiliary Heat 1 - 12

378 Heating Cycle Rate Emergency Heat

(TH6320U only) 1 - 12

Advanced setup options (ISU)

10

# ISU ISU Name ISU Options (factory default in bold)

387 Compressor Protection 0 = Off

1 - 5minutes

425 Adaptive Intelligent Recovery 0 = No

1 = Yes

Note: Adaptive Intelligent Recovery (AIR) is a comfort setting. Heating or cooling

equipment will turn on earlier, ensuring the indoor temperature will match the

setpoint at the scheduled time.

430 Minimum Cool Setpoint 50 °F to 99 °F (50 °F)

10.0 °C to 37.0 °C (10.0 °C)

431 Maximum Heat Setpoint 40 °F to 90 °F (90 °F)

4.5 °C to 32.0 °C (32.0 °C)

435 Keypad Lockout 0 = None

1 = Partial

2 = Full

500 Is Indoor Temperature Sensor

WIRED to your system? (TH6320U /

TH6220U only)

0 = No

1 = Yes

515 Indoor Sensor type

(TH6320U / TH6220U only) 0 = 10k

1 = 20k

520 Which Sensors will be used for

TEMPERATURE Control? (Multiple

Sensors are Averaged) TH6320U /

TH6220U only)

1 = Thermostat Only

2 = Wired Only

3 = Average

702 Number of Air Filters 0- 2

711 Air Filter 1 Replacement Reminder 0 = Off

1 = 10 Run Time Days

2 = 20 Run Time Days

3 = 30 Run Time Days

4 = 45 Run Time Days

5 = 60 Run Time Days

6 = 90 Run Time Days

7 = 120 Run Time Days

8 = 150 Run Time Days

9 = 30 Calendar Days

10 = 45 Calendar Days

11 = 60 Calendar Days

12 = 75 Calendar Days

13 = 3 Calendar Months

14 = 4 Calendar Months

15 = 5 Calendar Months

16 = 6 Calendar Months

17 = 9 Calendar Months

18 = 12 Calendar Months

19 = 15 Calendar Months

712 Air Filter 2 Replacement Reminder 0 = Off

1 = 10 Run Time Days

2 = 20 Run Time Days

3 = 30 Run Time Days

4 = 45 Run Time Days

5 = 60 Run Time Days

6= 90 Run Time Days

7 = 120 Run Time Days

8 = 150 Run Time Days

9 = 30 Calendar Days

10 = 45 Calendar Days

11 = 60 Calendar Days

12 = 75 Calendar Days

13 = 3 Calendar Months

14 = 4 Calendar Months

15 = 5 Calendar Months

16 = 6 Calendar Months

17 = 9 Calendar Months

18 = 12 Calendar Months

19 = 15 Calendar Months

1400 Backlighting 0 = On Demand

1 = Continuous

Note: Common wire needed for continuous.

1401 Backlight brightness 1 - 5

Note: Only displayed if continuous backlight selected.

1410 Clock Format 12 / 24

1415 Daylight Saving Time 0 = Off

1 = On

1420 Temperature Display Offset 3 to 3F (0)

1.5 to 1.5C (0)

Advanced setup options (ISU)