Honeywell TH4210U2002 Bedienungsanleitung

Package Includes:

• T4 Pro Thermostat

• UWP™ Mounting System

• Honeywell Standard Installation

Adapter (J-box adapter)

• Honeywell Decorative Cover Plate –

Small; size 449/64 in x 449/64 in x

11/32 in (121 mm x 121 mm x 9 mm)

• Screws and anchors

• 2 AA Batteries

• Installation Instructions and User

Guide

T4 Pro

Programmable Thermostat

Installation Instructions

Optional Cover Plate installation

NOTE: If Optional Cover Plate is not required,

see “UWP Mounting System installation” on

next page.

Use the Optional Cover Plate when:

• Mounting the thermostat to an electrical

junction box

• Or when you need to cover paint gap from

old thermostat.

1. Before starting, turn the power off at

the breaker box or switch. Separate the

Junction Box Adapter from the Cover

Plate. See Figure 1.

2. Mount the Junction Box Adapter to the

wall or an electrical box using any of the

eight screw holes. Insert and tighten

mounting screws supplied with Cover

Plate Kit. Do not overtighten. See Figure 2.

Make sure the Adapter Plate is level.

3. Attach the UWP by hanging it on the top

hook of the Junction Box Adapter and

then snapping the bottom of the UWP in

place. See Figure 3.

4. Snap the Cover Plate onto the Junction

Box Adapter. See Figure 4.

Use 2x

supplied

screws #6

5/8”

Power options

Insert AA batteries for primary or backup

power.

UWP Mounting System installation

Use 3x supplied

screws #8 11/2”

1. Before starting, turn the power off

at the breaker box or switch. Open

package to find the UWP. See Figure 5.

2. Position the UWP on wall. Level and

mark hole positions. See Figure 6.

Drill holes at marked positions, and

then lightly tap supplied wall anchors

into the wall using a hammer.

‒Drill 7/32” holes for drywall.

3. Pull the door open and insert the wires

through wiring hole of the UWP. See

Figure 7.

4. Place the UWP over the wall anchors.

Insert and tighten mounting screws

supplied with the UWP. Do not

overtighten. Tighten until the UWP

no longer moves. Close the door. See

Figure 8.

L/A

O/B

AUX

Insert Rand Cwires into

designated terminals for primary

AC power (C terminal is optional

if batteries are installed, but it is

recommended). Remove wires by

depressing the terminal tabs.

UWP Wiring terminal designations

SNot used for T4

thermostat.

L/A

- A Not used for T4 thermostat.

SO/B Changeover valve

YCompressor contactor

(stage 1)

AUX -

Auxiliary heat (TH4210U

only)

Y2 Not used for T4

thermostat. EEmergency heat (TH4210U

only)

GFan Relay WHeat relay (stage 1)

24VAC common. For 2

transformer systems,

use common wire from

cooling transformer.

KConnect to K on Wire Saver

Module**

UNot used for T4

thermostat.

R24VAC power from heating

transformer*

URc 24VAC power from cooling

transformer*

Note: Not all

terminals may be

used, depending

on the system

type that is being

wired. The most

commonly used

terminals are

shaded.

* Terminal can be jumped using Slider Tab. See “Setting Slider Tabs” above.

** The THP9045A1023 Wire Saver Module is used on heat/cool systems when you

only have four wires at the thermostat, and you need a fifth wire for a common wire.

Use the K terminal in place of the Y and G terminals on conventional or heat pump

systems to provide control of the fan and the compressor through a single wire—the

unused wire then becomes your common wire. See THP9045 instructions for more

information.

Set R Slider Tab.

• Use built-in jumper (R Slider Tab)

to differentiate between one or two

transformer systems.

• If there is only one R wire, and it is

connected to the R, Rc, or RH terminal, set

the slider to the up position (1 wire).

• If there is one wire connected to the R

terminal and one wire connected to the Rc

terminal, set the slider to the down position

(2 wires).

NOTE: Slider Tabs for U terminals should be

left in place for T4 Pro models.

Setting Slider Tabs (built-in jumper)

R/Rc Slider Tab

(built-in jumper)

UWP Mounting System

1H/1C System (1 transformer)

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

W Heat relay

G Fan relay

Heat-only System

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

C 24VAC common [3]

W Heat relay

Heat-only System (Series 20) [5]

R Series 20 valve terminal “R” [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Series 20 valve terminal “W”

C 24VAC common [3]

W Series 20 valve terminal “B”

Heat-only System

(power open zone valve) [5]

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

W Valve

C 24VAC common [3]

1H/1C System (2 transformers)

R Power (heating transformer) [1]

Rc Power (cooling transformer) [1]

Y Compressor contactor

C 24VAC common [3, 4]

W Heat relay

G Fan relay

Heat-only System with Fan

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

C 24VAC common [3]

W Heat relay

G Fan relay

Cool-only System

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

G Fan relay

1H/1C Heat Pump System

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

W Do not use this terminal for heat pump

applications!

2H/1C Heat Pump System (TH4210U only)

R Power [1]

Rc [R+Rc joined by Slider Tab] [2]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

AUX Auxiliary heat

E Emergency heat relay

L Heat pump fault input

W Do not use this terminal for heat pump

applications!

Wiring heat pump systems

Wiring conventional systems: forced air and hydronics

NOTES

Wire specifications: Use 18 to 22-gauge thermostat wire. Shielded cable is not required.

[1] Power supply. Provide disconnect means and overload

protection as required.

[2] Move RSlider Tab on UWP to the Rsetting. For more

information, see “Setting Slider Tabs (built-in jumper)” on

page 3

[3] Optional 24VAC common connection.

[4] Common connection must come from cooling transformer.

[5] In ISU set Heat system type to Radiant Heat. Set number of

cool stages to 0.

[7] In Installer Setup, set changeover valve to O (for cool

changeover) or B (for heat changeover).

Fan operation settings

1 Press the Fan button to cycle to the next

available Fan mode.

2 Cycle through the modes until the required

Fan mode is displayed and leave it to

activate.

NOTE: Available Fan modes vary with system

settings.

Fan modes:

‒Auto: Fan runs only when the heating or

cooling system is on.

‒On: Fan is always on.

Thermostat mounting

1. Push excess wire back into the wall

opening.

2. Close the UWP door. It should remain

closed without bulging.

3. Align the UWP with the thermostat, and

push gently until the thermostat snaps in

place.

4. Turn the power on at the breaker box or

switch.

System operation settings

1 Press the Mode button to cycle to the next

available System mode.

2 Cycle through the modes until the required

System mode is displayed and leave it to

activate.

NOTE: Available System modes vary by model

and system settings.

System modes:

‒Auto: Thermostat selects heating or cooling as

needed.

‒Heat: Thermostat controls only the heating

system.

‒Cool: Thermostat controls only the cooling

system.

‒Em Heat (TH4210U only) (only for heat

pumps with auxiliary heat): Thermostat

controls Auxiliary Heat. Compressor is not

used.

‒Off: Heating and cooling system is off. Fan will

still operate if fan is set to On.

1 Press and hold CENTER and buttons for

approximately 3 seconds to enter advanced

menu.

2 Press Select to enter ISU.

3 Press Select to cycle through menu setup

options.

4 Press or to change values or select

from available options.

5 Press Select and confirm your settings or

press Back to ignore changes and return

to ISU menu screen to continue editing

another setup option.

6 To finish setup process and save your

setting, press Home and return to Home

screen.

NOTE: A complete list of all setup (ISU)

parameters and options starts below and

continues through page 9.

Installer setup (ISU)

Advanced setup options (ISU)

NOTE: Depending on system settings, not all options may be available.

# ISU ISU Name ISU Options (factory default in bold)

120 Scheduling Options 0 = NonProgrammable

2 = 52 Programmable

3 = 511 Programmable

4 = 7Day Programmable

Note: You can change default MOFR, SASU schedule here.

To edit periods during days, temperature setpoints, or to turn

Schedule On/Off, touch MENU and go to SCHEDULE.

125 Temperature Indication Scale 0 = Fahrenheit

1 = Celsius

200 Heating System Type 1 = Conventional Forced Air Heat

2 = Heat Pump

3 = Radiant Heat

5 = None (Cool Only)

Note: This option selects the basic system type your thermostat

will control.

# ISU ISU Name ISU Options (factory default in bold)

205 Heating Equipment Type Conventional Forced Air Heat:

1 = Standard Efficiency Gas Forced Air

2 = High Efficiency Gas Forced Air

3 = Oil Forced Air

4 = Electric Forced Air

5 = Hot Water Fan Coil

Heat Pump:

7 = Air to Air Heat Pump

8 = Geothermal Heat Pump

Radiant Heat:

9 = Hot Water Radiant Heat

12 = Steam

Note: This option selects the equipment type your thermostat will

control. Note: This feature is NOT displayed if feature 200 is set

to Cool Only.

218 Reversing Valve O/B 0 = O (O/B in Cool)

1 = B (O/B in Heat)

Note: This option is only displayed if the Heat Pump configured.

Select whether reversing valve O/B should energize in cool or in

heat.

220 Cool Stages / Compressor

Stages 200=Conv / 200=HP 0, 1

Note: Select how many Cool or Compressor stages of your

equipment the thermostat will control. Set value to 0 if you do not

have Cool Stage/Compressor Stage.

221 Heat Stages / Backup Heat

Stages Heat Stages: 1

Backup Heat Stages: 0, 1

Note: Select how many Heat or Aux/E stages of your equipment

the thermostat will control.

230 Fan Control in Heat 1 = Equipment Controls Fan

2 = Thermostat Controls Fan

Note: This ISU is only displayed if ISU 205 is set to Electric Forced

Air or Fan Coil.

300 System Changeover 0 = Manual

1 = Automatic

Note: Thermostat can automatically control both heating and

cooling to maintain the desired indoor temperature. To be able to

select “automatic” system mode on thermostat home screen, turn

this feature ON. Turn OFF if you want to control heating or cooling

manually.

303 Auto Changeover Differential 0 °F to 5 °F

0.0 °C to 2.5 °C

Note: Differential is NOT deadband. Differential means how

far past the setpoint before switching to the mode selected.

Deadband setup is not an option. Honeywell uses an advanced

algorithm that fixes deadband at 0 °F. This is more advanced

than previous thermostats.

340 Backup Heat Droop

(TH4210U only) 0 = Comfort

2 = 2 °F

3 = 3 °F

4 = 4 °F

5 = 5 °F

6 = 6 °F

7 = 7 °F

8 = 8 °F

9 = 9 °F

10 = 10 °F

11 = 11 °F

12 = 12 °F

13 = 13 °F

14 = 14 °F

15 = 15 °F

Advanced setup options (ISU) (continued)

# ISU ISU Name ISU Options (factory default in bold)

350 Upstage Timer for Backup

Heat (TH4210U only) 0 = Off

1 = 30 minutes

2 = 45 minutes

3 = 60 minutes

4 = 75 minutes

5 = 90 minutes

6 = 2 hours

7 = 3 hours

8 = 4 hours

10 = 5 hours

365 Compressor Cycle Rate

(Stage 1) 1 - 6

Note: This ISU is only displayed when Cool /Compressor Stage

is set to 1 stage. Cycle rate limits the maximum number of times

the system can cycle in a 1 hour period measured at a 50%

load. For example, when set to 3 CPH, at a 50% load, the most

the system will cycle is 3 times per hour (10 minutes on, 10

minutes off). The system cycles less often when load conditions

are less than or greater than a 50% load.

370 Heating Cycle Rate (Stage 1) 1 - 12

Note: This ISU is only displayed when Heat Stage is set to 1 stage.

Cycle rate limits the maximum number of times the system can

cycle in a 1 hour period measured at a 50% load. For example,

when set to 3 CPH, at a 50% load, the most the system will cycle

is 3 times per hour (10 minutes on, 10 minutes off). The system

cycles less often when load conditions are less than or greater

than a 50% load. The recommended (default) cycle rate settings

are below for each heating equipment type: Standard Efficiency

Gas Forced Air = 5 CPH; High Efficiency Gas Forced Air = 3 CPH;

Oil Forced Air = 5 CPH; Electric Forced Air = 9 CPH; Fan Coil = 3

CPH; Hot Water Radiant Heat = 3 CPH; Steam = 1 CPH.

375 Heating Cycle Rate Auxiliary

Heat (TH4210U only) 1 - 12

387 Compressor Protection 0 = Off

1 - 5minutes

Note: The thermostat has a built in compressor protection

(minimum off timer) that prevents the compressor from restarting

too early after a shutdown. The minimum-off timer is activated

after the compressor turns off. If there is a call during the

minimum-off timer, the thermostat shows “Wait” in the display.

This ISU is displayed if ISU 220 is set to at least 1 stage.

425 Adaptive Intelligent Recovery 0 = No

1 = Yes

Note: Adaptive Intelligent Recovery (AIR) is a comfort setting.

Heating or cooling equipment will turn on earlier, ensuring the

indoor temperature will match the setpoint at the scheduled time.

430 Minimum Cool Setpoint 50 °F to 99 °F (50 °F)

10.0 °C to 37.0 °C (10.0 °C)

Note: The cool temperature cannot be set below this level.

431 Maximum Heat Setpoint 40 °F to 90 °F (90 °F)

4.5 °C to 32.0 °C (32 °C)

Note: The heat temperature cannot be set above this level.

435 Keypad Lockout 0 = None

1 = Partial

2 = Full

Note:

Unlocked: User has access to all thermostat settings.

Partially Locked: User can modify only temperature settings.

Fully Locked: User cannot modify any settings. Screen will be

locked by default factory code and cannot be changed. This

code is displayed for a short time, when you are about to lock the

thermostat screen. Please

note the code in safe place for future reference.

Advanced setup options (ISU) (continued)

# ISU ISU Name ISU Options (factory default in bold)

702 Number of Air Filters 0- 2

Note: This ISU refers to the number of air filters in the system.

711 Air Filter 1 Replacement

Reminder 0 = Off

1 = 10 Run Time Days

2 = 20 Run Time Days

3 = 30 Run Time Days

4 = 45 Run Time Days

5 = 60 Run Time Days

6 = 90 Run Time Days

7 = 120 Run Time Days

8 = 150 Run Time Days

9 = 30 Calendar Days

10 = 45 Calendar Days

11 = 60 Calendar Days

12 = 75 Calendar Days

13 = 3 Calendar Months

14 = 4 Calendar Months

15 = 5 Calendar Months

16 = 6 Calendar Months

17 = 9 Calendar Months

18 = 12 Calendar Months

19 = 15 Calendar Months

Note: Set a reminder for when to change your air filter. Choose

either calendar or equipment run time-based reminder.

712 Air Filter 2 Replacement

Reminder 0 = Off

1 = 10 Run Time Days

2 = 20 Run Time Days

3 = 30 Run Time Days

4 = 45 Run Time Days

5 = 60 Run Time Days

6 = 90 Run Time Days

7 = 120 Run Time Days

8 = 150 Run Time Days

9 = 30 Calendar Days

10 = 45 Calendar Days

11 = 60 Calendar Days

12 = 75 Calendar Days

13 = 3 Calendar Months

14 = 4 Calendar Months

15 = 5 Calendar Months

16 = 6 Calendar Months

17 = 9 Calendar Months

18 = 12 Calendar Months

19 = 15 Calendar Months

Note: Set a reminder for when to change your air filter. Choose

either calendar or equipment run time-based reminder.

1400 Backlighting 0 = On Demand

1 = Continuous

Note: Common wire needed for continuous.

1401 Backlight brightness 1 - 5

Note: Only displayed if continuous backlight selected.

1410 Clock Format 12 / 24

1415 Daylight Saving Time 0 = Off

1 = On

Note: Set to Off in areas that do not follow Daylight Saving Time.

1420 Temperature Display Offset 3 to 3F (0)

1.5 to 1.5C (0)

Note: 0 °F - No difference in displayed temperature and the

actual room temperature. The thermostat can display up to 3 °F

(1.5 C) lower or higher than the actual measured temperature.

Specifications

Temperature Ranges

Heat: 40 °F to 90 °F (4.5 °C to 32.0 °C)

Cool: 50 °F to 99 °F (10.0 °C to 37.0 °C)

Operating Ambient Temperature

37 °F to 102 °F (2.8 °C to 38.9 °C)

Shipping Temperature

20 °F to 120 °F (28.9 °C to 48.9 °C)

Operating Relative Humidity

5% to 90% (non-condensing)

Physical Dimensions in inches (mm) (H x W x D)

41/16” H x 41/16” W x 15/32” D

103.5 mm H x 103.5 mm W x 29 mm D

Installer system test

To perform a System Test:

1 Press and hold CENTER and buttons for

approximately 3 seconds to enter advanced

menu.

2 Use to go to TEST. Press Select to enter

System Test.

3 Use to change between Heat, Cool, Fan,

Em. Heat (TH4210U only), or Ver (thermostat

version information). Press Select.

4 Press to turn heat, cool, or fan on. Press to

turn them off.

5 Use the Home button to exit the System Test.

System test System status

Heat

0Heat Off

1Heat On

2Heat On (TH4210U only)

Cool 0Cool Off

1Cool On

Fan 0Fan Off

1Fan On

Em. Heat

(TH4210U only)

0Em. Heat Off

1Em. Heat On

Electrical Ratings

Terminal Voltage (50/60Hz) Running Current

WHeating 2030 Vac 0.021.0 A

(Powerpile) 750 mV DC 100 mA DC

W2 (Aux) Heating (TH4210U only) 2030 Vac 0.021.0 A

EEmergency Heat (TH4210U only) 2030 Vac 0.020.5 A

YCompressor Stage 1 2030 Vac 0.021.0 A

GFan 2030 Vac 0.020.5 A

O/B Changeover 2030 Vac 0.020.5 A

L/A Input 2030 Vac 0.020.5 A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell CMT927 Bedienungsanleitung

Honeywell

Honeywell HEAT PUMP THERMOSTAT T8411R Bedienungsanleitung

Honeywell

Honeywell Chronotherm modulation Bedienungsanleitung

Honeywell

Honeywell PRESTIGE THX9321 Bedienungsanleitung

Honeywell

Honeywell EVOTOUCH CONTROLLER Bedienungsanleitung

Honeywell

Honeywell RTH5100B Bedienungsanleitung

Honeywell

Honeywell FOCUSPRO TH5320C Bedienungsanleitung

Honeywell

Honeywell T4098A Bedienungsanleitung

Honeywell

Honeywell Prestige Bedienungsanleitung

Honeywell

Honeywell Magic Stat MS3000 Bedienungsanleitung

Honeywell

Honeywell DT92 Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8110U Bedienungsanleitung

Honeywell

Honeywell T8401C1031 Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Bedienungsanleitung

Honeywell

Honeywell Lyric Round TH8732WFH-5002/U Bedienungsanleitung

Honeywell

Honeywell ST9400A Bedienungsanleitung

Honeywell

Honeywell T8196A/Q682A Bedienungsanleitung

Honeywell

Honeywell TH2110 Bedienungsanleitung

Honeywell

Honeywell TH9000 Series Bedienungsanleitung

Honeywell

Honeywell RCT8101 Bedienungsanleitung

Honeywell

Honeywell RTH9585WF1004 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung