Honeywell RTH5160 Series Bedienungsanleitung

RTH5160 Series

Non-Programmable

Thermostat

Quick Installation Guide

Tools you will need Tools you may need

Wire stripper

Needle-nose pliers Drill and

drill bit (7/32 in)

Included in your box

Screws and

anchors

UWP™

Mounting

System

(UWP)

RTH5160

Thermostat

Quick Install Guide

Small ﬂat head scr

ewdriver

Phillips scr

ewdriver

Pencil

Level

Quick Installation Guide

Removing your old thermostat

2 Check that your system is off.

Change the temperature on your

old thermostat to be above room

temperature in heat mode or below

it in cool mode. If you don’t hear the

system turn on within 5 minutes, the

power is off.

Note: If you have a digital

thermostat that has a blank display,

skip this step.

1 Turn power OFF.

To protect yourself and your

equipment, turn off the power at

the breaker box or the switch that

controls your heating/cooling

system.

3 Remove the old thermostat’s

faceplate.

On most thermostats, you can take

off the faceplate by grasping and

gently pulling. Some thermostats

may have screws, buttons, or clasps.

Do not remove any wires from your

thermostat at this time!

OFF

Breaker box

Switch

4 Make sure there are no 120/240V

wires.

Do you have thick black wires with

wire nuts?

Is your thermostat 120V or higher?

If you answered yes to either of

these questions, you have a line

voltage system and the thermostat

will not work.

Wire nut

Thick black wire

RTH5160 Series

5 Take a picture of how your wiring

looks right now.

Be sure to include the letters next

to the terminals where the wires

are inserted. This will be a helpful

reference when wiring your new

thermostat.

Tip: If the color of your wires has

faded or if 2 terminals have the

same wire color, use the wire labels

provided in the package to label

each wire.

YRRC

Example of

a jumper

Terminals

1/4” to 3/8”

6 Record which R-wire(s) you have and write down the color of the wire(s).

Note: Do not include jumpers as a part of your count. The thermostat does

not need jumpers.

Terminal Wire Color

7 Record the remaining wires and write down the color of the wires.

Check mark the wires that are connected to terminals. Next to the check mark,

write down the color of the wire. Do not include jumpers as a part of your

count.

Check all that apply (Not all will apply):

Terminal Wire Color

A or L/A

O/B

W2 or AUX

NOTES:

• Cdoes not power the thermostat display or operations; batteries are

always required.

• If Kwas used on old thermostat you have a wire-saver at the equipment.

Re-wiring would need to be done so that Y and G are used instead of K.

• The RTH5160 thermostat does not support L/A, S, or U terminals.

• If there are wires in terminals that are not listed, you will need

additional wiring support. Visit yourhome.honeywell.com/support to

ﬁnd out if the thermostat will work for you.

Quick Installation Guide

8 Disconnect the wires and remove the old wall plate.

Use a screwdriver to release wires from terminals. Then, use a wire label to

identify each wire as it’s disconnected. The letter on the wire label should

match the letter on the terminal.

Tip: To prevent wires from falling back into the wall, wrap the wires around a

pencil.

Installing your RTH5160 thermostat

9 Bundle and insert wires through the UWP.

Pull open the UWP and insert the bundle of

wires through the back of the UWP.

Make sure at least 1/4 inch of each wire

is exposed for easy insertion into the wire

terminals.

RTH5160

Thermostat Screws UWP

Mounting

System Anchors Wall

RTH5160 Series

10 Insert the wall anchors.

It is recommended that you use the

wall anchors included in the box to

mount your thermostat.

You can use the UWP to mark where

you want to place the wall anchors.

a) Level the wall plate.

b) Mark the location of the wall

anchors using a pencil.

c) Drill the holes.

d) Insert wall anchors.

e) Make sure anchors are ﬂush with

wall.

Tip: Use a 7/32 drill bit.

Insert wires into the inner holes of the terminals on the UWP. The tabs will

stay down once the wire is inserted.

If you have 1 R-wire (R, Rh, or Rc)

If you have 2 R-wires (R or Rh, and Rc)

1. Set R-switch

to the up

position.

1. Set R-switch

to the down

position.

2. Insert your

R-wire (R, Rh

or Rc) into

R-terminal.

2. Insert your Rc wire

into Rc-terminal

3. Insert your R

or Rh wire into

RTerminal.

11 Set R-switch position and insert R-wire(s).

Set the R-switch up or down based on your wiring notes in Step 6.

NOTE: Alternate wiring options are shown on pages 1112.

Quick Installation Guide

13 Confirm wiring matches snapshot.

Please confirm wiring matches terminals from the photo you took in Step 5.

14 Mount the UWP and close the door.

Mount the UWP using the provided screws. Install all three screws for a secure

fit on your wall. Close the door after you’re finished.

Use 3x supplied

screws #8 11/2”

1/4” to 3/8”

12 Connect remaining wires.

Depress the tabs to put the

wires into the inner holes of the

corresponding terminals on the

UWP (one wire per terminal) until it is

firmly in place.

Gently tug on the wires to verify

they are secure.

Tip: If you need to release a wire

again, push down the corresponding

terminal tab on the side of the UWP.

NOTE: Alternate wiring options are

shown on pages 1112.

This wiring is just an example,

yours may vary.

RTH5160 Series

15 Install batteries.

Insert two AA alkaline batteries in the back of the thermostat as shown.

16 Attach your thermostat.

Align the thermostat onto the UWP

and firmly snap it into place.

17 Turn your power ON.

Turn on the power at the breaker box

or switch that controls the heating/

cooling system.

OFF

Breaker box

Switch

Quick Installation Guide

Now that you have installed your thermostat, please follow the steps below to

setup your system and personalize your thermostat.

18 Select System Setup options.

Press Edit (-) to change values or select from available options. Then press

Next (+) to save changes and advance to the next System Setup number.

See “System Setup options” on the next page for a full list of

System Setup

numbers and options

Repeat until all of the System Setup options have been set, and then press

Done. The thermostat will save and exit to the home screen.

19 Continue to “System operation settings” on page 10.

System Setup

Setup number Option number

NOTE: To re-enter the System Setup from the Home Screen, press and hold

the Menu button for approximately 5 seconds.

RTH5160 Series

System Setup Number and Description Options (factory default in bold)

125 = Temperature Indication Scale 0 = Fahrenheit

1 = Celsius

200 = Heating System Type

1 = Conventional Forced Air Heat

2 = Heat Pump

3 = Radiant Heat (Boiler)

5 = None (Cool Only)

Note: This option selects the basic system type your thermostat will

control.

205 = Heating Equipment Type

Conventional Forced Air Heat:

1 = Standard Efficiency Gas Forced Air

2 = High Efficiency Gas Forced Air

3 = Oil Forced Air

4 = Electric Forced Air

5 = Hot Water Fan Coil

Heat Pump:

7 = Air to Air Heat Pump

Radiant Heat:

9 = Hot Water Radiant Heat

12 = Steam

Note: This option selects the equipment type your thermostat will

control. This feature is NOT displayed if feature 200 is set to Cool Only.

218 = Reversing Valve O/B

0 = O (O/B in Cool)

1 = B (O/B in Heat)

Note: This option is only displayed if the Heat Pump configured. Select

whether reversing valve O/B should energize in cool or in heat.

220 = Cool Stages / Compressor Stages

(200=Conv / 200=HP)

0, 1, 2

Note: Select how many Cool or Compressor stages of your equipment

the thermostat will control. Maximum of 2 Cool stages or 1 Compressor

stage. Set value to 0 if you do not have Cool Stage/Compressor Stage.

221 = Heat Stages / Backup Heat Stages

Heat Stages: 1, 2

Backup Heat Stages: 0, 1

Note: Select how many Heat or Aux/E stages of your equipment the

thermostat will control. Maximum of 2 Heat Stages for conventional

systems. Maximum of 1 Aux/E stage for systems with more than 1

heating equipment type. Set value to 0 if you do not have Heat Stage/

Backup Heat Stage.

300 = System Changeover

0 = Manual

1 = Automatic

Note: Thermostat can automatically control both heating and cooling

to maintain the desired indoor temperature. To be able to select

“automatic” system mode on thermostat home screen, turn this feature

ON. Turn OFF if you want to control heating or cooling manually.

NOTE: Once you have cycled through all of the System Setup numbers, press

Done to save and exit to the home screen.

System Setup options

Setup Complete

You have now finished installing and setting up your thermostat.

Quick Installation Guide

Fan operation settings

1 Press Menu, and then press the Fan (-)

button to cycle to the next available

Fan mode.

2 Cycle through the modes until the

required Fan mode is displayed,

then press Done.

NOTE: Available Fan modes vary with

system settings.

Fan modes:

‒Auto: Fan runs only when the

heating or cooling system is on.

‒On: Fan is always on.

System operation settings

1 Press Menu, and then press the

Mode (+) button to cycle to the next

available System mode.

2 Cycle through the modes until the

required System mode is displayed,

and then press Done.

NOTE: Available System modes vary by

model and system settings.

System modes:

‒Auto: Thermostat selects heating

or cooling as needed.

‒Heat: Thermostat controls only the

heating system.

‒Cool: Thermostat controls only the

cooling system.

‒Em Heat (only for heat pumps

with auxiliary heat): Thermostat

controls Auxiliary Heat. Compressor

is not used.

‒Off: Heating and cooling system is

off. Fan will still operate if fan is set

to On.

NOTE: Heat On/Cool On may flash for 5

minutes due to compressor protection.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell RTH1120B Bedienungsanleitung

Honeywell

Honeywell TH8321WF1001 Allgemeine Anweisungen

Honeywell

Honeywell TROL-A-TEMP Q674B Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell SuperStat Bedienungsanleitung

Honeywell

Honeywell FocusPRO 5000 Bedienungsanleitung

Honeywell

Honeywell RTH8500WF Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5220D Bedienungsanleitung

Honeywell

Honeywell WebStat T7350 Betriebsanleitung

Honeywell

Honeywell AQ1000TN2 - Low Voltage T-Stat Bedienungsanleitung

Honeywell

Honeywell TL8100A1008 - Line Voltage Thermostat Bedienungsanleitung

Honeywell

Honeywell TH401 Bedienungsanleitung

Honeywell

Honeywell DT92E Bedienungsanleitung

Honeywell

Honeywell Chronotherm IV T8601D Bedienungsanleitung

Honeywell

Honeywell RTH2410B1001E1 Bedienungsanleitung

Honeywell

Honeywell RTH8500D - 7-Day Touchscreen Universal Programmable... Bedienungsanleitung

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell T8602A2055 Systemhandbuch

Honeywell

Honeywell CT1500 Bedienungsanleitung

Honeywell

Honeywell T8112D Kurzanleitung

Honeywell

Honeywell T8700B Bedienungsanleitung

Honeywell

Honeywell T7100D Bedienungsanleitung

Honeywell

Honeywell XE70 SERIES Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung