Honeywell T7351 Bedienungsanleitung

Place Bar Code Here

63-2652—01

T7351

Programmable Thermostat

FOR CONVENTIONAL/HEAT PUMP

SYSTEMS

User’s Guide

63-2652_A.fm Page 1 Monday, May 10, 2010 4:21 PM

63-2652—01 2

FEATURES

• Typically used in buildings (including:

restaurants, shopping malls, office

buildings and banks) under 55,000

square feet.

• For single zone rooftop units, split

systems, heat pumps or hot/chilled water

systems.

• 7-day programming.

• Two Occupied and two Not Occupied

periods per day.

• Keypad multi-level lockout available with

all models.

• Individual heat and cool setpoints

available for Occupied and Not Occupied

periods.

• Convenient overrides allow temporary

setpoint changes.

• Intelligent Fan™ feature energizes fan

continuously in the Occupied periods.

Fan can also be configured for

conventional heat or electric heat fan

operation.

• Remote sensor capability for temperature

(including outdoor air and discharge air)

and humidity sensors.

• Recovery ramping control automatically

optimizes equipment start times based

on building load.

• Universal Versaguard™ Thermostat

guards available.

• Auxiliary subbase contact typically

interface with a Honeywell Economizer

System (for total rooftop control

integration) or act as dehumidification

output.

63-2652_A.fm Page 2 Monday, May 10, 2010 4:21 PM

3 63-2652—01

SETTINGS

Using Thermostat Keys

The thermostat keys are used to:

• set current time and day,

• program times and setpoints for heating and

cooling,

• override the program temperatures,

• display present setting,

• set system and fan operation,

• perform simple configuration.

NOTE: See Fig. 1 for keypad information.

Setting Temperature

Refer to Table 1 for default temperature

setpoints. See Programming section for

complete instructions on changing these.

Table 1. Default Setpoints.

Control Occupied Not Occupied Standby

Heating 70°F(21°C) 55°F(13°C) 67°F(19°C)

Cooling 75 °F (24 °C) 85 °F (29 °C) 78 °F (26 °C)

63-2652_A.fm Page 3 Monday, May 10, 2010 4:21 PM

63-2652—01 4

Setting System and Fan

System default setting is Auto. The fan default

is set so the fan operates continuously during:

— Occupied periods,

— Heating and cooling equipment stages in

Not Occupied and recovery periods.

NOTE: Use System and Fan keys to change

settings.

System Settings

— Auto: Thermostat automatically changes

between heating and cooling based on

sensed indoor temperature.

— Cool: Thermostat controls cooling.

— Off: Heating, cooling, and fan are all off.

— Heat: Thermostat controls heating.

— Em Heat: Auxiliary heat serves as first stage.

Compressor stages are locked off.

Fan Settings

— On: Fan operates continuously in occupied

and standby periods. Fan cycles with call for

heat or cool during not occupied periods.

— Auto: Fan cycles with call for heating or

cooling during occupied, standby, and not

occupied periods.

NOTE: This is further modified by selection of

conventional or electric heat.

63-2652_A.fm Page 4 Monday, May 10, 2010 4:21 PM

5 63-2652—01

PROGRAMMING

The thermostat operates at the Occupied

temperature setting unless the thermostat is

programmed. The program has four settings:

— Occupied heat.

— Occupied cool.

— Not Occupied heat.

— Not Occupied cool.

The thermostat can be set for two Occupied

and two Not Occupied times for each day of the

week (28 independent time settings). The

Temporary Occupied key provides quick

setpoint changes for increased comfort during

Not Occupied periods. The Temporary Not

Occupied key provides energy efficient

operation for extended periods of time.

IMPORTANT

Programming the thermostat with the

keypad requires 24 Vac (turn on sys-

tem power). The keyboard lockout

feature must be disabled.

NOTE: Before starting programming, use

Table 2 to organize the program

schedule.

63-2652_A.fm Page 5 Monday, May 10, 2010 4:21 PM

63-2652—01 6

Table 2. Occupied and Not Occupied Period Start Times.

NOTE: 12:00 PM is noon, and 12:00 AM is midnight.

Day

Occupied

Period 1

Not Occupied

Period 1

Occupied

Period 2

Not Occupied

Period 2

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

63-2652_A.fm Page 6 Monday, May 10, 2010 4:21 PM

7 63-2652—01

Fig. 1. Thermostat key locations.

When using the keypad to change the day/time:

1. Press Set Day until the current day is

displayed.

NOTE: Sun = Sunday, Mon = Monday,

Tue = Tuesday,

Wed = Wednesday,

Thu = Thursday,

Fri = Friday, Sat = Saturday.

2. Press Set Time.

3. Press up Sor down Tuntil the current

time is displayed.

System Fan Run

Schedule

CopyNot OccupiedOccupiedDay

Clear

Start Time

Day Time

Temperature

Temporary

Occupied

Override

HEAT HEATCOOL COOL

HEAT COOL ON AUTO

Schedule

Set Day/Time

Occupied

Not Occupied

Temporary

Not Occupied

M19610BB

63-2652_A.fm Page 7 Monday, May 10, 2010 4:21 PM

63-2652—01 8

NOTE: Tapping Set Time changes the

time in one hour increments.

4. Press Run Schedule.

Setting Schedule Times

Use the keys in the “Schedule” area of the

keypad for this procedure.

1. Press Occupied.

NOTE: Anytime a start time is not

required, press Clear Start Time.

2. Press Day until desired day is displayed.

3. Press Occupied or Not Occupied until the

proper period is displayed.

4. Press up Sor down Tuntil the desired

start time is displayed.

5. Repeat steps 3 and 4 for a given day.

6. Repeat steps 2 through 5 until finished.

Copying a Day

Use the keys in the “Schedule” area of the

keypad for this procedure.

NOTE: The thermostat must be in program

mode to use the copy feature. If the

thermostat is already in program

mode, skip step 1.

1. Press Occupied.

2. Press Day to select the day to be copied.

3. Press Copy.

4. Press Copy again.

5. Press Day until the day to receive the

copy is displayed.

6. Press Copy.

NOTE: DONE displays for two seconds

then the program display reap-

pears.

63-2652_A.fm Page 8 Monday, May 10, 2010 4:21 PM

9 63-2652—01

7. Repeat steps 2 through 6 for all the days

desired.

8. Press Run Schedule.

Clearing Program Start

Times

1. Press Occupied or Not Occupied until the

start period to be cleared is displayed.

2. Press Day until desired day is displayed.

3. Press Clear Start Time.

4. Repeat steps 1 through 3 for all the start

times to be cleared.

5. Press Run Schedule.

Temperature Setpoints

Setpoint Limits

The setpoint temperature range is 40 to 90 °F

(4 to 32 °C) for heating and 45 to 99 °F (7 to

37 °C) for cooling.

NOTE: These limits may be restricted by the

installer to comply with local energy

codes.

Programming Temperature

Setpoints

1. Press Occupied Heat.

2. Press up Sor down Tuntil the desired

temperature is displayed.

3. Press Occupied Cool.

4. Press up Sor down Tuntil the desired

temperature is displayed.

63-2652_A.fm Page 9 Monday, May 10, 2010 4:21 PM

63-2652—01 10

5. Press Not Occupied Heat.

6. Press up Sor down Tuntil the desired

temperature is displayed.

7. Press Not Occupied Cool.

8. Press up Sor down Tuntil the desired

temperature is displayed.

9. Press Run Schedule.

Temperature Setpoint

Overrides

IMPORTANT

— Setup determines Occupied override

duration.

— Default duration is three hours.

NOTE: To cancel Override and immediately

return to the program, press Run

Schedule.

TR23 Setpoint Knob

A TR23 setpoint knob can remotely adjust the

T7350 setpoint. This adjustment can be made

when the sensor is in override.

NOTES:

— During override, only occupied and

standby heat setpoints, and cool

setpoints are adjusted.

— The maximum adjustment is ±5 °F

(±3 °C).

— With a disconnected or failed TR23

or a T7350 set for local tempera-

ture sensing, offset is zero.

63-2652_A.fm Page 10 Monday, May 10, 2010 4:21 PM

Andere Handbücher für T7351

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell TH114-A-240D Bedienungsanleitung

Honeywell

Honeywell Lyric T5 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell D Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell Chronotherm III Bedienungsanleitung

Honeywell

Honeywell T8700B Bedienungsanleitung

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell VT15 Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8110U Bedienungsanleitung

Honeywell

Honeywell LYRIC T4 Bedienungsanleitung

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell E529.RF Bedienungsanleitung

Honeywell

Honeywell PRO TH4000 series Bedienungsanleitung

Honeywell

Honeywell THX9000 Prestige HD Benutzerhandbuch

Honeywell

Honeywell T6R-HW Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell AQ1000TN2 - Low Voltage T-Stat Bedienungsanleitung

Honeywell

Honeywell Q539A Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 IAQ Bedienungsanleitung

Honeywell

Honeywell T7300F Bedienungsanleitung

Honeywell

Honeywell RTH7000 Bedienungsanleitung

Honeywell

Honeywell RTH6360 Series Bedienungsanleitung

Honeywell

Honeywell 2080WL Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung