Honeywell T8011F Bedienungsanleitung

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69- 1558

T8011F Flush Mount

Programmable Heat Pump Thermostat

APPLICATION

The T8011F Heat Pump Thermostat provides 24 Vac

control of a two-stage heating and one-stage cooling

heat pump system with manual changeover from heat to

cool. First stage heating and cooling cycle rates are fixed

at 3 cph. Second stage heating cycle rate is selectable 3,

6, 9, or 12 cph. Temperature indication can be set for °F

or °C.

The T8011F Heat Pump Thermostat is powered directly

from the system transformer. Setpoints are held

permanently in memory and retained during power

outages.

The T8011F model includes a thermostat, wallplate and

Owner’s Guide. See Table 1.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of it properly.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of the control.

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

Hazardous Voltage.

Can damage heating/cooling system.

Disconnect power at furnace or main breaker/

fuse box.

Location

Install the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average temperature.

See Fig. 1. Do not install the thermostat where it can be

affected by:

— drafts or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from the sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

Installing Wallplate in Wall

IMPORTANT

Level only for appearance. The thermostat func-

tions normally even when not level.

Mount wallplate and the T8011F with the wing anchors

provided (see Fig. 2) as follows:

1. Place the wallplate template at the desired location

on the wall.

2. Trace and cutout the opening.

3. Pull the thermostat wire through the wallplate

entrance hole.

4. Fasten the wallplate to the wall using the wing

anchors.

Table 1. Description of T8011F Thermostat.

Model System Changeover System Selection Fan Selection Powering Method

T8011F Heat Pump Manual Cool-Off-Heat-Em. Ht. Auto-On Hardwired

T8011F FLUSH MOUNT PROGRAMMABLE HEAT PUMP THERMOSTAT

69-1558 2

Fig. 1. Typical location of thermostat.

Fig. 2. Mounting wallplate to wall.

Wiring

IMPORTANT

Use an 18-gauge maximum wire for wiring the

T8011F Thermostat.

All wiring must comply with local electrical codes and

ordinances. Disconnect the power supply to prevent

electrical shock or equipment damage.

The shape of the terminals permits insertion of straight or

wraparound wiring connections; either method is

acceptable. A letter code is located near each terminal

for identification. See Fig. 3.

NOTE: To ensure proper mounting of thermostat,

restrict all wiring to the shaded area in the cen-

ter of the terminals. See Fig. 4.

Fig. 3. Wiring connections.

5 FEET

[1.5 METERS]

YES

M11338

WALL

MOUNTING

SCREWS (2)

WALLPLATE

M18610

WING

ANCHORS (

M2015

TERMINAL

SCREW

FOR WRAP

AROUND

STRIP 7/16 IN.

(11 MM)

OR STRAIGHT

NSERTION

TRIP 5/16 IN.

(

9 MM)

T8011F FLUSH MOUNT PROGRAMMABLE HEAT PUMP THERMOSTAT

3 69-1558

Fig. 4. Restrict wiring to shaded area.

The T8011F Thermostat is powered directly from the

system transformer and is adaptable to most 18 to

30 Vac heating-cooling systems. All T8011F Thermostats

require a common wire to supply power. Refer to Fig. 6

for a typical wiring hookup.

Mounting Thermostat to Wallplate

1. Slide SYSTEM switch to the Off position.

2. Slide the thermostat straight into the wallplate until

it is flush against the wall. See Fig. 5.

Fig. 5. Mounting thermostat to wallplate.

Fig. 6. T8011F two-stage heat, one-stage cool wiring diagram with manual changeover.

MOUNTING

SCREW HOLE

KEEP WIRING IN

SHADED AREA

MOUNTING

SCREW HOLE

WIRING

ENTRANCE HOLE (2) M2015

KEEP WIRING IN

SHADED AREA

Hold

Fan

Auto

Select

TUE

PRESS THERMOSTAT STRAIGHT

BACK ONTO WALLPLATE M2015

Heat Em. Ht

System

Cool Off

(HOT

)

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

REMOVE JUMPER, WHEN SUPPLIED, FOR SYSTEMS WITH SEPARATE HEATING COMPRESSOR CONTACTOR (W1 SEPARATE FROM Y).

NOT ALL MODELS HAVE BOTH O AND B TERMINALS.

SYSTEM

SWITCH

HEAT

OFF

COOL

EM. HT.

AUXILARY

HEAT RELAY

CHANGEOVER

VALVE HEAT

CHANGEOVER

VALVE COOL

COMPRESSOR

CONTACTOR

COMPRESSOR

CONTACTOR

HEAT

FAN RELAY

RELAY

EMERGENCY

HEAT RELAY

THERMOSTAT

LOGIC

THERMISTOR

SENSOR

POWER

SUPPLY

AUTO

STAGE 2 RELAY

STAGE 1 RELAY

FAN SWITCH

M11333A

T8011F FLUSH MOUNT PROGRAMMABLE HEAT PUMP THERMOSTAT

69-1558 4

INSTALLER SETUP

Setting °F/°C Indication and Heat Cycle Rate

The following instructions provide the information

necessary to change the heating cycle rate to match the

heating equipment and to choose either Fahrenheit (°F)

or Celsius (°C) display.

NOTE: All four steps must be completed to save

changes to the °F/°C indication and the heat

cycle rate.

1. Enter Installer Setup.

a. Use ▲or ▼keys to

set the temperature

setpoint to 52°F

(11°C).

b. Press the ▲and ▼keys simultaneously for

more than two seconds to enter installer setup.

c. When released, the

three-digit software

revision code is dis-

played.

d. Press the ▲key.

Factory configura-

tion (FC) is dis-

played. (A typical

example is shown,

but information dis-

played varies by model. This information is for

factory use only).

Optional System Checkout

When in steps 1c and 1d only, pressing the ▼key can be

used to turn heat or cool outputs on and off. Change the

SYSTEM switch setting to test heat or cool outputs. No

action takes place If the system switch is in the Off

position.

Examples:

— System setting at HEAT: If heat is on, pressing

the ▼key turns it off; if heat is off, pressing the

▼key turns it on.

— System setting at COOL: If cool is on, pressing

the ▼key turns it off; if cool is off, pressing the

▼key turns it on. The 5 minute minimum off

time is bypassed.

NOTE: In installer setup only, each press of the ▲key

momentarily displays 1. Each press of the ▼

key momentarily displays 2. When the keys are

released, these one-digit codes are no longer

displayed.

2. Setting °C or °F.

a. Press the ▲key

again to display the

current setting.

b. Press the ▼key to

change the °C or °F

indication.

3. Setting Heat Cycle Rate

(see Table 2 for the

cycle rate options and

equipment).

a. Press the ▲key to

display the current

heat cycle rate set-

ting of 1, 3, 4, 5, 6,

9, or 12 cph.

b. To change the heat

cycle rate, press the

▼key until your

choice of 1, 3, 4, 5,

6, 9, or 12 is dis-

played. See Table

c. Press the ▲key to

display control algo-

rithm configuration

default.

d. Press the ▲key

again to change

control algorithm to C1 or C3.

C1 = Standard control algorithm.

C3 = Aggressive control algorithm (can

cause overshooting).

e. Press the ▲key

again. Current con-

figuration (CC) is

displayed. A typical

example is shown,

but CC varies by

model. (This information is for factory use only.)

4. Exit

Installer

Setup.

a. Press

the ▲

key to

save all

changes and return to normal operation.

Table 2. Heating Cycle Rate

aHigh efficiency furnace (90+).

bRefer to the equipment manufacturer’s instructions.

NOTE: Stage one heat and cool cycle rates are fixed at

3 cph. Only stage two heat cycle rates are

selectable.

OPERATION

Setting FAN and SYSTEM Switches

Fan and system settings are controlled manually by

using the switches located at the bottom of the

thermostat case. See Fig. 7.

M12582

SET

HT.

M1258

M12584

M12587A

M12586

System Cycles Per Hour

Steam, gravity 1

Hydronic heat, condensing gas

furnacesa

Gas or oil forced air 6

Electric heat 9

Special applicationsb4, 5, 12

M12588

M12589A

M1469

M12590A

T8011F FLUSH MOUNT PROGRAMMABLE HEAT PUMP THERMOSTAT

5 69-1558

FAN Switch

Fan switch settings are:

On: The fan runs continuously. Use for improved air

circulation and air quality.

Auto: Normal setting for most homes. In cooling, the

fan starts and stops with the cooling equipment. In

heating, the fan is controlled directly by the heating

equipment and may start a few minutes after the

heating equipment turns on (most systems). When

the fan operation (fuel) switch is in the E position,

the fan starts and stops with the heating equip-

ment.

Slide the FAN switch in the lower left corner of the

thermostat to select the desired fan setting.

SYSTEM Switch

System switch settings control thermostat operation as

follows:

Cool: The thermostat controls the cooling system.

Off: Both heating and cooling are off.

Heat: The thermostat controls the heating system.

Em. Ht.: The thermostat cycles auxiliary heat (W2)

and emergency heat relay (E), as needed, to main-

tain setpoint. Terminal L is energized continuously

(fault heat relay is on continuously). Cooling sys-

tem is off. Compressor is de-energized.

Slide the SYSTEM switch in the lower right corner of the

thermostat to select the desired system setting.

Fig. 7. Digital Display and System switches.

Setting Current Time and Day

1. To Set Current Time.

a. Press Select twice.

b. Press ▲or ▼to set

current time.

2. To Set Day of Week.

a. Press Select again.

b. Press ▲or ▼to set

current day.

To use the preprogrammed

time and temperature (see

Table 3) press Hold to exit the

programming mode.

Setting Time and Temperature

The T8011F is preprogrammed with the time and

temperature settings shown in Table 3. For instructions

on programming the thermostat refer to the Owner’s

Guide, form no. 69-1557.

Table 3. Preprogrammed Time and

Temperature Settings.

CHECKOUT

Heating

1. Slide the SYSTEM switch to Heat and the FAN

switch to Auto.

2. Press and hold the ▲key to raise the temperature

setting several degrees above the room tempera-

ture; the heating equipment should start. In con-

ventional systems, the system turns on the fan

through the use of a time delay relay or through a

limit control. When the fan operation (fuel) switch is

in the E position, the fan starts immediately.

3. Press the ▼key to lower the temperature setting

below the room temperature. Heating equipment

should stop.

Cooling

CAUTION

Damage To compressor possible.

Operating at too low of an outdoor

temperature may cause compressor damage.

Do not operate cooling if outdoor temperature is

below 50°F (10°C).

Allow compressor to remain off for five minutes

before restarting.

Refer to manufacturer’s recommendations.

1. Slide the SYSTEM switch to Cool and the FAN

switch to Auto.

2. Press the ▼key to lower the temperature setting

several degrees below the room temperature; the

cooling equipment should start. The fan starts and

stops with the cooling equipment.

Hold

Fan

Auto

Select

TUE

M20160

Heat Em. Ht

System

Cool Off

M12591

SET

M12592A

SET

Period Time Heat Setpoint Cool Setpoint

Wake 6:00 AM 70°F (21°C) 78°F (26°C)

Leave 8:00 AM 62°F (17°C) 85°F (29°C)

Return 6:00 PM 70°F (21°C) 78°F (26°C)

Sleep 10:00 PM 62°F (17°C) 82°F (28°C)

M12593

M12594A

T8011F FLUSH MOUNT PROGRAMMABLE HEAT PUMP THERMOSTAT

69-1558 6

NOTE: If unit does not start immediately, remem-

ber that the thermostat has a built-in mini-

mum off-time of five minutes to protect the

compressor.

3. Press the ▲key to raise the temperature setting

above the room temperature. Cooling system

should shut down.

Fan

1. Slide the SYSTEM switch to Off and the FAN

switch to On. The fan should run continuously.

2. Slide the FAN switch to Auto. In heating, the fan is

controlled directly by the heating equipment and

may start a few minutes after the heating equip-

ment turns on (on most systems). In cooling, the

fan starts and stops with the cooling equipment.

Make certain all equipment responds correctly to the

thermostat.

7 69-1465—2

69-1558 G.H. 7-01 Printed in Mexico www.honeywell.com/yourhome

Home and Building Control Home and Building Control

Honeywell Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Scarborough, Ontario

M1V 4Z9

Andere Handbücher für T8011F

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell FocusPRO TH6110D Bedienungsanleitung

Honeywell

Honeywell CM900 Bedienungsanleitung

Honeywell

Honeywell Prestige Bedienungsanleitung

Honeywell

Honeywell RTH2510/RTH2410 Series Bedienungsanleitung

Honeywell

Honeywell 1-Heat/1-Cool - TH5110D1022 Large R Bedienungsanleitung

Honeywell

Honeywell Chronotherm modulation Bedienungsanleitung

Honeywell

Honeywell SUITEPRO TB6575 Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell PRESTIGE THX9321 Bedienungsanleitung

Honeywell

Honeywell RTH2510 Series Bedienungsanleitung

Honeywell

Honeywell RTH6500WF Wi-Fi Series Bedienungsanleitung

Honeywell

Honeywell THX9000 Prestige HD Benutzerhandbuch

Honeywell

Honeywell VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell Honeywell Thermostat PRO TH3000 Series Bedienungsanleitung

Honeywell

Honeywell TB7600 Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell T812A1010 - Premier 1 Heat Stage Thermostat Bedienungsanleitung

Honeywell

Honeywell RTH8500WF Leitfaden

Honeywell

Honeywell lyric round Bedienungsanleitung

Honeywell

Honeywell EnergyPro T8665C Bedienungsanleitung

Honeywell

Honeywell CM707 Montageanleitung

Honeywell

Honeywell DTS92A Bedienungsanleitung

Honeywell

Honeywell TC500A Bedienungsanleitung

Honeywell

Honeywell RTH2310B Bedienungsanleitung

Honeywell

Honeywell VVT Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung