Honeywell T841A Bedienungsanleitung

MOUNTING

HOLES (4)

WIRING TERMINAL

(UP TO 12) M2960A

BACK OF DEVICE

EM. HEAT HEAT OFF COOL

AUTO ON

FAN EM. HEAT AUX. HEAT

CHECK

FRONT OF DEVICE

FAN SWITCH

SYSTEM SWITCH

COVER

THERMOMETER

SET POINT

SCALE

LED (UP

TO THREE)

T841A Heating-Cooling

Heat Pump Thermostat

X-XX UL

INSTALLATION INSTRUCTIONS

®U.S. Registered Trademark

APPLICATION

The T841A Heating-Cooling TRADELINE® Thermostat

provides 24 Vac control of two-stage heating and one-

stage cooling in heat pump systems, using manual

changeover. This thermostat provides SYSTEM switch

selections of EM. HEAT-HEAT-OFF-COOL and FAN

switch selections of AUTO-ON. See Fig. 1. See Table 1 for

T841A TRADELINE® specifications.

Test holes are provided on the front of the thermostat to

accommodate test meter probes without removing the

thermostat from the wall. Remove the cover of the

thermostat to expose the test holes, which are labeled to

correspond with the terminals on the back of the

thermostat.

Table 1. T841A TRADELINE® Specifications.

Fig. 1. External view of T841A.

aEM. HEAT LED also indicates compressor malfunction.

bPremier White® color.

cSold only in Australia: degrees C.

dCHECK LED indicates compressor malfunction.

OS Number

LED

Indication Changeover

Heat

Anticipation

Terminal

Designations Remarks

System

Switch

Auto Fan

in EM.

HEAT

T841A1308 EM. HEAT

AUX. HEAT

Manual Cool

or Heat

Stage 2 fixed,

0 to 1.5A

G, R, W

, E,

L, B, X, Y, O

Use when E

and W

are

jumpered.

EM. HEAT,

HEAT, OFF,

COOL

T841A1316 G, R, E, L, X

, B, W1,

, O

Does not

replace

T841A1068.

Yes

T841A1423

EM. HEAT,

AUX. HEAT,

CHECK

Stage 2

adjustable, 0.1

to 1.2A

, G, R, W

E, L, B, X, Y,

Not for systems

with E to W

jumper

T841A1464

b,c

T841A1498 EM. HEAT Stage 2 fixed,

0 to 1.5A

G, R, W, H, B,

X, O, Y

Exact

replacement for

York model no.

2TH11703324

T841A1506

69-0452-8

69-0452—8 2

T841A HEATING-COOLING HEAT PUMP THERMOSTAT

OPERATION

The stages of heat

make

sequentially as the temperature

drops.

Make

refers to the mercury switch initiating a call for

heat or cool.

There is about 1°F (0.6°C) between stages so the second

stage (auxiliary heat) makes only when the first stage

cannot handle the load. This 1°F is the

interstage differen-

tial

The LED indicators on certain thermostat models light up

when something specific happens within the system.

When the green or amber LED lights, the auxiliary heat

(second stage heat) is operating because the weather is

so cold, the heat pump alone cannot handle the load.

When the red EM. HEAT LED lights, the emergency heat

is operating (usually electric strip heaters), because the

homeowner has physically switched to the EM. HEAT

position. See heating/cooling manufacturer instructions for

specific meaning.

RECYCLING NOTICE

This control contains mercury in a sealed tube. Do

not

place the control in the trash at the end of its

useful life. If this control is replacing a control that

contains mercury in a sealed tube, do

not

place

your old control in the trash.

Contact your local waste management authority for

instructions regarding recycling and the proper

disposal of this control, or any control containing

mercury in a sealed tube.

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

1. Disconnect power supply to prevent electrical

shock or equipment damage.

2. To prevent interference with the thermostat

linkage, keep wire length to a minimum and

run wires as close as possible to the thermo-

stat base.

3. Do not overtighten the thermostat captive

mounting screws, because damage to the

threads can result.

4. Do not short across coil terminals on the relay.

This can burn out the thermostat heat

anticipator.

5. Never install more than one wire per terminal

unless a factory-supplied jumper with spade

terminal is used.

Location

Locate the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average room tempera-

ture.

Do not mount the thermostat where it can be affected by:

—drafts, or dead spots behind doors and in corners.

—hot or cold air from ducts.

—radiant heat from sun, appliances or fireplaces.

—concealed pipes and chimneys.

—unheated (uncooled) areas such as an outside wall

behind the thermostat.

This thermostat is a precision instrument and was carefully

adjusted at the factory.

Handle it carefully.

Mounting and Wiring

CAUTION

Disconnect power supply before beginning

installation. Can cause electrical shock or

equipment damage.

The T841A can be mounted directly to a wall or

horizontal outlet box. Choose the method that best fits

your installation.

In replacement applications, check the existing thermostat

wires for cracked or frayed insulation. Replace wires in

poor condition.

All wiring must comply with local codes and ordinances.

69-0452—8

T841A HEATING-COOLING HEAT PUMP THERMOSTAT

ODT 1

EHR 1 RTD 2

RTD 1

ODT 2

RTD 3

ERH 2

SYSTEM

SWITCH

EM. HEAT

HEAT

OFF

COOL

FALL

H1 & C1

ANTICIPATOR

H2 ANTICIPATOR

FAN

SWITCH

AUTO

COMPRESSOR

CONTACTOR

EM. HEAT

RELAY

CHANGEOVER

RELAY (HEAT)

AUX. HT.

LED (GREEN)

LACO CHP

M1099B

CHANGEOVER

RELAY (COOL)

(HOT)

FAN RELAY

SYSTEM

MONITOR RTD 1

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

WHEN SYSTEM MONITOR IS CONNECTED TO L TERMINAL, EM. HT.

LED ALSO INDICATES COMPRESSOR MALFUNCTION.

X TERMINAL MUST BE CONNECTED FOR PROPER OPERATION.

EM. HT.

LED

(RED) 2

Grasp the thermostat cover at the top and bottom with one

hand. Pull outward on the bottom edge of the cover until it

snaps free of the thermostat base. Carefully remove and

save the packing material surrounding the mercury

switches.

1. Run the wiring (if necessary) to the location. If the

wiring is plastered into the wall, make a hole next to

the cable and loosen the wires so that they can be

pushed back into the wall later. Thread the wires

through the hole in the packing material saved

above. Connect the wires to the terminals on the

back of the thermostat. See Fig. 2 through 5.

2. Set the second stage adjustable heat anticipator to

match the current draw of the primary heating

control (see Heat Anticipator Setting section).

3. Push the excess wire back through the hole and

plug any opening with packing material to prevent

drafts that may affect thermostat performance.

4. Use screws to loosely secure the thermostat to the

wall or outlet box through the two mounting holes in

the middle of the device.

The sheetmetal screws included with the thermostat are

designed for use in plaster walls that do not need anchors.

IMPORTANT

An incorrectly leveled thermostat causes

inaccurate temperature control.

5. Level the thermostat using a spirit level or plumb

line. Tighten the two mounting screws at the middle

of the device.

6. Install the two screws in the top mounting holes and

tighten.

7. Replace the thermostat cover.

SETTINGS

Heat Anticipator Setting

The second stage heat anticipator is adjustable. Move the

adjustable indicator to match the current draw of the

second stage heating primary control, or the anticipator

setting of the old thermostat. See Fig. 6.

Temperature Setting

Move the setpoint lever to the desired control point on the

temperature scale.

SYSTEM Switch Setting

The SYSTEM switch positions control the system opera-

tion as follows:

EM. HEAT: Emergency heat relay is energized. Cooling

system is off. Compressor is de-energized. Fan runs

on call for heat if FAN switch is in the AUTO

position. EM. HEAT LED is on.

HEAT: Heating system is automatically controlled by

the thermostat. Cooling system is off.

OFF: Both the heating and cooling systems are off. If

the fan is at the AUTO position, the cooling fan is

also off.

COOL: Cooling system is automatically controlled by

the thermostat. Heating system is off.

FAN Switch Setting

AUTO: Fan operates in response to thermostat in both

heating and cooling.

ON: Fan operates continuously.

Fig. 2. Internal schematic and typical wiring diagram for TRADELINE® T841A1308 with EM. HEAT and AUX. HEAT

LEDs. No fan control in EM. HEAT. Provides heat or cool changeover relay control.

69-0452—8 4

T841A HEATING-COOLING HEAT PUMP THERMOSTAT

Fig. 3. Internal schematic and typical wiring diagram for SUPER TRADELINE® T841A1316 with AUX. HEAT and

EM. HEAT LEDs. Provides heat or cool changeover relay control and automatic fan in EM. HEAT mode.

(HOT) L2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

REMOVE W1-Y1 JUMPER WHEN HEAT RELAY 1 IS USED.

WHEN L TERMINAL IS CONNECTED TO SYSTEM MONITOR, EM. HEAT LED ALSO INDICATES COMPRESSOR MALFUNCTION.

X TERMINAL MUST BE CONNECTED FOR PROPER OPERATION.

H2 ANTICIPATOR

FALL

H1 ANTICIPATOR

C1 ANTICIPATOR

SYSTEM

SWITCH

HEAT

OFF

COOL

FAN SWITCH

AUTO

EM. HT.

COMPRESSOR

CONTACTOR

FAN RELAY

EM. HT.

RELAY

EM. HT.

LED (RED)

CHANGEOVER

RELAY (HEAT)

AUX. HT.

LED (GREEN)

HEAT RELAY 1

CHANGEOVER

RELAY (COOL)

AUX. HT.

RELAY

JUMPER

SYSTEM

MONITOR

M1103E

Fig. 4. Internal schematic and typical wiring diagram for TRADELINE® T841A1498 and T841A1506

with EM. HEAT LED. Provides cooling changeover relay control.

FALL

C1 L1

(HOT)

EM. HT.

LED (RED)

OFF

COOL

HEAT

EM. HT.

SYSTEM

SWITCH

FAN

SWITCH

AUTO

ON FAN RELAY

HEAT RELAY

"H" RELAY

EM. HT. RELAY

CHANGEOVER

RELAY (COOL)

COMPRESSOR

CONTACTOR

H1/C1

ANTICIPATOR

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

B TERMINAL MUST BE CONNECTED FOR PROPER OPERATION.

AUTO FAN IN EM. HEAT.

M3171B

69-0452—8

T841A HEATING-COOLING HEAT PUMP THERMOSTAT

Fig. 5. Internal schematic and typical wiring diagram for TRADELINE® T841A1423 and T841A1464 (sold only in

Australia) with AUX. HEAT, EM. HEAT and CHECK LEDs. Provides heat or cool changeover relay control and

automatic fan in EM. HEAT mode.

H2 FALL

FALL

(HOT) L2

SYSTEM

SWITCH

EM. HT.

HEAT

OFF

COOL

H1/C1

ANTICIPATOR

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

AUTO FAN IN EM. HEAT.

FAN

SWITCH

AUTO

AUX. HT.

LED (GREEN)

EM. HT.

LED (RED)

CHECK

LED (RED)

COOL CHANGE-

OVER VALVE

M6059C

COMPRESSOR

CONTACTOR

HEAT CHANGE-

OVER VALVE

SYSTEM MONITOR

EM. HT. RELAY

RTD 1

FAN REALY

RTD 3EHR 2

ODT 2

RTD 1 ODT 1

EHR 1 RDT 2

LACO CHP

Fig. 6. Second stage adjustable heat anticipator indicator.

1.2

.8.6 .4

.15

.12

.10

EM.HEAT HEAT OFF COOL

MOVE INDICATOR

TO MATCH CURRENT

RATING OF PRIMARY CONTROL

M2962B

LONGER

69-0452—8 6

T841A HEATING-COOLING HEAT PUMP THERMOSTAT

CHECKOUT

Heating

Move the SYSTEM switch on the thermostat to HEAT and

the FAN switch to AUTO. Move the setpoint lever to about

10°F (6°C) above the room temperature. Heating should

start and the fan should run. Move the setpoint lever about

10°F (6°C) below the room temperature. Heating and fan

should shut off.

NOTE: To prevent compressor short cycling, a minimum-

off timer may be included to prevent the com-

pressor from starting for up to five minutes from

when the thermostat last turned the compressor

off, or from when the system first received power.

Cooling

CAUTION

Do not operate cooling if outdoor temperature is

below 50°F (10°C). Refer to manufacturer recom-

mendations.

Move the SYSTEM switch on the thermostat to COOL

and the FAN switch to AUTO. Move the setpoint lever

about 10°F (6°C) below the room temperature. Cooling

and fan should start. Move the setpoint lever about 10°F

(6°C) above the room temperature. Cooling and fan

should shut off.

Fan

Move the SYSTEM switch to OFF, and the FAN switch to

ON. The fan should run continuously. Move the FAN

switch to AUTO. In this position, the fan operates in

response to the thermostat in both heating and cooling.

69-0452—8 J.S. Rev. 5-97 www.honeywell.com/yourhome

Honeywell Limited-Honeywell Limitée

35 Dynamic Drive

Scarborough, Ontario M1V 4Z9

Automation and Control Solutions

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

Andere Handbücher für T841A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T Series Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell CM901 Montageanleitung

Honeywell

Honeywell VisionPRO THM5421C1008 Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5220D Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5000 Series Bedienungsanleitung

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell CM707 Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell TH1100DH Bedienungsanleitung

Honeywell

Honeywell T7200D Bedienungsanleitung

Honeywell

Honeywell Wi-Fi VisionPRO 8000 series Bedienungsanleitung

Honeywell

Honeywell TH8320R1003 Bedienungsanleitung

Honeywell

Honeywell RRTH9590WF Bedienungsanleitung

Honeywell

Honeywell lyric round Bedienungsanleitung

Honeywell

Honeywell TP979A-E Bedienungsanleitung

Honeywell

Honeywell The Round CT87K Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8000 Series Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell T6 Pro Smart Bedienungsanleitung

Honeywell

Honeywell CT50A Bedienungsanleitung

Honeywell

Honeywell RTH2410B1001E1 Bedienungsanleitung

Honeywell

Honeywell TRADELINE Q7300L Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung