Honeywell T8401C1031 Bedienungsanleitung

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1484-2

T8400C1099, T8401C1031

Electronic Thermostats

The T8400 and T8401 Thermostats provide single-stage,

non-programmable temperature control for 24V heating-

cooling systems with manual changeover from heat to

cool. Heating cycle rate is selectable at 1, 3, 4, 5, 6, 9, or

12 cph. Cooling cycle rate is fixed at 3 cph. Temperature

indication can be set for °F or °C.

The T8400 Thermostat is powered through the heating/

cooling system controls. The T8401 requires a common

wire for operation. Batteries are not required because

setpoints are held permanently by non-volatile memory.

The T8400 and T8401 models include a thermostat,

wallplate (for wiring and mounting thermostat) and

owner’s guide.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of an old control containing

mercury in a sealed tube.

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

Electrical Shock or Equipment Damage

Hazard.

Can shock individuals or short equipment

circuitry.

Disconnect power supply before installation.

Location

Install the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average temperature.

See Fig. 1. Do not install the thermostat where it can be

affected by:

— drafts or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from the sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

This thermostat is a precision instrument and was

carefully adjusted at the factory. Handle it carefully.

Mounting Wallplate to Wall

IMPORTANT

Level only for appearance. The thermostat func-

tions normally even when not level.

Mount the T8400 and T8401 with the screws provided

(see Fig. 2) as follows:

1. Place the wallplate at the desired location on the

wall.

2. Pull the thermostat wire through the entrance hole

on the wallplate.

3. Fasten the wallplate to the wall using the anchors

and screws provided.

4. After wiring the wallplate, plug the hole to prevent

drafts from affecting the thermostat; see Wiring

section.

T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS

69-1484-2 2

Fig. 1. Typical location of thermostat.

Fig. 2. Mounting wallplate to wall.

Setting Fan Operation (Fuel) Switch

The fan operation (fuel) switch is preset at the factory in

the F position. See Fig. 3. This is the correct setting for

most systems. If this system is an electric heat system,

set the switch to the E position. The E setting allows the

fan to turn on immediately with the heating or cooling

equipment in a system where the G terminal is

connected.

Wiring

IMPORTANT

Use an 18-gauge maximum wire to wire the

T8400 and T8401 Thermostats.

All wiring must comply with local electrical codes and

ordinances. Disconnect the power supply to prevent

electrical shock or equipment damage.

NOTE: To ensure proper mounting of thermostat,

restrict all wiring to the shaded area. See Fig. 4.

The shape of the terminals permits insertion of straight or

wraparound wiring connections; either method is

acceptable. See Fig. 5.

Refer to Fig. 6 through 10 for typical wiring hookups.

Fig. 3. Fan operation (fuel) switch.

5 FEET

[1.5 METERS]

YES

M11338

M12202A

WALL WALL

ANCHORS (2)

WALLPLATE

WHEN USING WALL ANCHORS, DRILL 3/16 INCH

HOLES FOR DRYWALL, 7/32 INCH HOLES FOR

PLASTER OR WOOD.

MOUNTING

SCREWS (2)

M12580

FAN OPERATION (FUEL) SWITCH

T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS

3 69-1484-2

Fig. 4. Restrict wiring to shaded area

(T8400C1099 shown).

Fig. 5. Wiring connections

(T8400C1099 shown).

Fig. 6. Typical hookup of T8400C1099 in heat-cool

system with single transformer.

Fig. 7. Typical hookup of T8400C1099 in heat-cool

system with two transformers.

Fig. 8. Typical hookup of T8400C1099 in single-stage

heat pump systems.

KEEP WIRING IN

SHADED AREA

MOUNTING

SCREW HOLE MOUNTING

SCREW HOLE

WIRING ENTRANCE

HOLE

M16432

TERMINAL

SCREW

M13274

FOR STRAIGHT INSERTION

STRIP 5/16 IN. (8 MM)

FOR WRAPAROUND

STRIP 7/16 IN. (11 MM

)

(HOT)

COOLING

CONTACTOR

FAN

RELAY

HEATING

PRIMARY

CONTROL

24V

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

FACTORY INSTALLED JUMPER. M13275

M12562

(HO

FAN

RELAY

HEAT

RELAY

(

HOT)

COMPRESSOR

CONTACTOR

HEATING

TRANSFORMER

COOLING

TRANSFORMER

HEAT

DAMPER

COOL

DAMPER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

REMOVE RC TO R JUMPER WHEN INSTALLED ON A TWO TRANSFORMER

SYSTEM.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT

PUMP SYSTEMS.

POWER TO R TERMINAL IS REQUIRED WHEN THE SYSTEM SWITCH IS IN

THE OFF POSITION.

(

HOT)

COOL

CHANGEOVER

FAN

RELAY

COMPRESSOR

24V

M2088

HEAT

CHANGEOVER

TRANSFORMER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS

AND OVERLOAD PROTECTION AS REQUIRED.

CAN BE USED FOR CHANGEOVER VALVE ON

SINGLE-STAGE HEAT PUMP SYSTEMS.

FACTORY INSTALLED JUMPER.

FIELD INSTALLED JUMPER.

T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS

69-1484-2 4

Fig. 9. Typical hookup of T8401C1031 in heat-cool

system.

Fig. 10. Typical hookup of T8401C1031 in single-

stage heat pump system.

Mounting Thermostat to Wallplate

1. Engage the tabs at the top of the thermostat and

wallplate.

2. Swing down the thermostat and press the lower

edge of the thermostat onto the wallplate to latch.

See Fig. 11.

Fig. 11. Mounting thermostat wallplate.

OPERATION

Setting FAN and SYSTEM Switches

Fan and system settings are controlled manually by

using the switches located at the bottom of the

thermostat case. See Fig. 12.

FAN Switch

Fan switch settings are:

On: The fan runs continuously. Use for improved air

circulation and air quality.

Auto: Normal setting for most homes. In cooling, the

fan starts and stops with the cooling equipment. In

heating, the fan is controlled directly by the heating

equipment and may start a few minutes after the

heating equipment turns on (on most systems).

When using an electric heat thermostat, the fan

starts and stops with the heating equipment.

Slide the FAN switch in the bottom left corner of the

thermostat to select the desired fan setting.

(

HOT)

1FAN

RELAY

COOL

RELAY

HEAT

RELAY

24V

M2088

TRANSFORMER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS

AND OVERLOAD PROTECTION AS REQUIRED.

(

HOT)

COOL

CHANGEOVER

FAN

RELAY

COMPRESSOR

24V

M2088

HEAT

CHANGEOVER

TRANSFORMER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS

AND OVERLOAD PROTECTION AS REQUIRED.

CAN BE USED FOR CHANGEOVER VALVE ON

SINGLE-STAGE HEAT PUMP SYSTEMS.

FIELD INSTALLED JUMPER.

M14677

SYSTEM

Cool Off Heat

Auto On

FAN

DASHED LINES INDICATE TABS

ON BACK OFTHERMOSTAT

SYSTEM

Cool Off Heat

Auto On

FAN

ENGAGE TABS ATTOP OFTHERMOSTAT

WITH SLOTS ON MOUNTING PLATE.

PRESS LOWER EDGE OF

CASETO LATCH.

T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS

5 69-1484-2

SYSTEM Switch

System switch settings control thermostat operation as

follows:

Cool: The thermostat controls the cooling system.

Off: Both heating and cooling are off.

Heat: The thermostat controls the heating system.

Slide the SYSTEM switch in the bottom right corner of

the thermostat to select the desired system setting.

Fig. 12. Digital display and system

switches (FAN and SYSTEM).

Set Temperature Setpoint

NOTE: Temperature setpoint range is 40° to 99°F (5° to

37°C).

The temperature setpoint and the room temperature are

shown separately on the digital display. The ▼indicator

points to Set when the temperature setpoint is displayed

and to Room when the room temperature is displayed.

To set temperature setpoint:

1. Select Heat or Cool by sliding the SYSTEM switch

in the lower right corner of the thermostat to the

desired mode. See Fig. 12.

2. To display the temperature setpoint on the digital

display, press either the ▲or ▼key once. The tem-

perature setpoint is displayed for approximately

five seconds as the indicator points to Set and

flashes.

3. To increase the temperature setpoint press the ▲

key. Each press changes the setpoint one degree;

press and hold to change the setpoint several

degrees.

4. To decrease the temperature setpoint press the ▼

key. Each press changes the setpoint one degree;

press and hold to change the setpoint several

degrees.

Setting °F/°C Indication and Heat Cycle Rate

NOTE: To save changes to the °F/°C indication, the

heat cycle rate and the C3/C1 temperature

control, tap the ▲key until exiting the installer

setup.

To set the °F/°C indication, the heat cycle rate and the

C3/C1 temperature control:

1. If the temperature is displayed in °F, set the tem-

perature setpoint to 52°F. If the room temperature

is displayed in °C, set the temperature setpoint to

11°C.

OPTIONAL SYSTEM CHECKOUT

When in steps 2 and 3 only, the

▼

key can be used to

turn heat or cool outputs on and off. Change the

SYSTEM switch setting to test heat or cool outputs. No

action takes place If the system switch is in the Off

position.

Examples: System setting at HEAT: If heat is on, the ▼

key turns it off; if heat is off, ▼turns it on.

System setting at COOL: If cool is on, ▼key

turns it off; if cool is off, ▼turns it on.

2. Press the ▲▼ keys simultaneously for more than

one second to light all segments on display and to

enter installer setup mode. When the keys are

released, a two-digit software revision code is dis-

played.

SYSTEM

Cool Off Heat

Auto On

FAN

M14678

TEMPERATURE DISPLAY

INCREASE SETTING

DECREASE SETTING

FAN SWITCH

SYSTEM SWITCH

et Room

INDICATOR

ROOM TEMPERATURE

SETPOINT TEMPERATURE M1467

M1468

T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS

69-1484-2 6

NOTE: In installer setup mode only, each press of the

▲key momentarily displays 01. Each press of

the ▼key momentarily displays 02. When the

keys are released, these two-digit codes are no

longer displayed.

3. Press the ▲key. Factory information is displayed.

A typical example is shown, but information dis-

played varies by model. This information is for fac-

tory use only.

4. Press the ▲key again to display °C or °F.

5. Press the ▼key to change the °C or °F indication.

6. Press the ▲key to display the heat cycle rate of 1,

3, 4, 5, 6, 9, or 12. To change the heat cycle rate,

press the ▼key to scroll between 1, 3, 4, 5, 6, 9, or

12. Stop scrolling when the desired rate is dis-

played. See Table 1 for the cycle rate options and

the corresponding system equipment.

7. Press the ▲key to display heating/cooling temper-

ature control default..

8. Press the ▼key again to change heating/cooling

temperature control to C1 or C3.

C1 = Standard heating/cooling temperature

control.

C3 = Aggressive heating/cooling temperature

control (can cause room temperature to

overshoot the setpoint).

9. Press the ▲key again. Factory information (varies

by model) is shown.

Table 1. Heating Cycle Rates.

aHigh efficiency furnace.

bRefer to equipment manufacturer’s instructions.

10. Press the ▲key to save all changes, exit installer

setup mode and return to normal operation.

NOTE: After exiting installer setup mode, slide the

System switch to the desired position and

change the setpoint to the desired room

temperature.

CHECKOUT

Heating

1. Slide the SYSTEM switch to Heat and the FAN

switch to Auto.

2. Press and hold the ▲key to raise the temperature

setting several degrees above the room tempera-

ture. After approximately ten seconds, the heating

equipment should start. In conventional systems,

the system turns on the fan through the use of a

time delay relay or through a limit control. When

using an electric heat thermostat, the fan starts

immediately.

3. Press the ▼key to lower the temperature setting

below the room temperature. Heating equipment

should stop.

Cooling

CAUTION

Low Temperature Hazard.

Operating at too low of an outdoor

temperature may cause compressor damage.

Do not operate cooling if outdoor temperature is

below 50°F (10°C). Refer to manufacturer’s

recommendations.

• For compressor protection, during power

interruption and on initial startup, the T8400

and T8401 Thermostats go into a five-minute

delay. During this delay, the cooling icon (a

snowflake ❄) flashes.

1. Slide the SYSTEM switch to Cool and the FAN

switch to Auto.

2. Press the ▼ key to lower the temperature setting

several degrees below the room temperature. After

approximately five minutes, the cooling equipment

should start. The fan starts and stops with the cool-

ing equipment.

M1468

M1469

M18419

M1842

System Cycles Per Hour

Steam, gravity 1

Hydronic heat, condensing gas

furnacea

Gas or oil forced air 6

Electric heat 9

Special applicationsb4, 5, 12

T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS

7 69-1484-2

3. Press the ▲key to raise the temperature setting

above the room temperature. Cooling system

should shut down.

NOTE: To bypass the five-minute delay, see the

Optional System Checkout section.

Fan

1. Slide the SYSTEM switch to Off and the FAN

switch to On. The fan should run continuously.

2. Slide the FAN switch to Auto. In heating, the fan is

controlled directly by the heating equipment and

may start a few minutes after the heating equip-

ment turns on (on most systems). When using an

electric heat thermostat, the fan starts and stops

with the heating equipment. In cooling, the fan

starts and stops with the cooling equipment.

Be sure all equipment responds correctly to the

thermostat.

69-1484-2 G.H. Rev. 11-02 Printed in Mexico www.honeywell.com/yourhome

T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS

Automation and Control Solutions

Honeywell Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Scarborough, Ontario

M1V 4Z9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell Single Stage Heat Pump ProgrammableCommercial... Bedienungsanleitung

Honeywell

Honeywell TH8110R1008/U Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8000 Series Bedienungsanleitung

Honeywell

Honeywell CT50A Bedienungsanleitung

Honeywell

Honeywell smartfit Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE WEB-HMI4/C Bedienungsanleitung

Honeywell

Honeywell ultrastat CT1700A Bedienungsanleitung

Honeywell

Honeywell RTH2300B Bedienungsanleitung

Honeywell

Honeywell CM707 Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell T8112D Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Bedienungsanleitung

Honeywell

Honeywell PRESTIGE THX9321 Bedienungsanleitung

Honeywell

Honeywell Smart Series Bedienungsanleitung

Honeywell

Honeywell TRADELINE T874 Bedienungsanleitung

Honeywell

Honeywell RTH7600D Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8000 Series Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell VISIONPRO TH8321U1097 Bedienungsanleitung

Honeywell

Honeywell TrueZONE HZ432 Bedienungsanleitung

Honeywell

Honeywell RTH3100C Bedienungsanleitung

Honeywell

Honeywell PRO 2000 TH2210D Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung