Honeywell THX9000 Prestige HD Benutzerhandbuch

Prestige™Thermostat

With wireless accessories

® U.S. Registered Trademark.

Control for up to 3 Heat/2 Cool heat pump systems or up to

2 Heat/2 Cool conventional systems.

DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical

shock or equipment damage.

MERCURY NOTICE: If this product is replacing a control that contains mercury in a

sealed tube, do not place the old control in the trash. Contact your local waste

management authority for instructions regarding recycling and proper disposal.

Must be installed by a trained, experienced technician. Read these instructions

carefully. Failure to follow these instructions can damage the product or cause a

hazardous condition.

System

Installation

Guide

Français : voir la page 17 • Español: vea la página 33

Installation guide for:

• THX9000 Prestige HD and Prestige SD thermostats

• Wireless remote control

• Wireless outdoor air sensor

Prestige™ Installation Guide

System installation at a glance

Thermostat

Outdoor

air sensor

Remote

control

Installation procedure

Mount and wire thermostat ........................................Pages 3-7

Customize thermostat (installer setup) ............................Page 8

Install batteries in wireless accessories ..........................Page 8

Link accessories to thermostat ................................Pages 9-10

Mount outdoor sensor ....................................................Page 11

To replace system components if needed, see page 14

DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical

shock or equipment damage.

HVAC equipment

If you have more than one thermostat: Optional accessories must be linked

to each thermostat separately.

Français : voir la page 17 • Español: vea la página 33

Mount and wire thermostat

Pull wiring through hole in wallplate and install as shown below.

Wiring

Wiring must comply with local electrical codes.

Drywall: 3/16” hole

Plaster: 7/32” hole

Wall anchor

Mounting screw

Strip 1/4” insulation and connect wires to screw terminals as shown below

(see wiring guides on following pages).

Factory-installed jumper System wiring

Prestige™ Installation Guide

Wiring guide

See detailed wiring guides for specific system types on following pages.

Conventional Terminal Letters:

CCommon wire from secondary side of

cooling transformer.

Rc Cooling power. Connect to secondary

side of cooling system transformer.

RHeating power. Connect to secondary

side of heating system transformer.

WHeat relay (stage 1).

W2 Heat relay (stage 2).

YCompressor contactor (stage 1).

Y2 Compressor contactor (stage 2).

GFan relay.

KTHP9054 connection (see note below)

Heat Pump Terminal Letters:

CCommon wire from secondary side of

cooling system transformer.

Rc Cooling power. Connect to secondary

side of cooling system transformer.

RHeating power. Connect to secondary

side of heating system transformer.

O/B Changeover valve for heat pumps.

Aux/E Auxiliary/Emergency heat relay.

YCompressor contactor (stage 1).

Y2 Compressor contactor (stage 2).

GFan relay.

LHeat pump reset (powered continuously

when System is set to Em Heat; system

monitor when set to Heat, Cool or Off).

KTHP9054 connection (see note below)

Note: Use the Kterminal in place of the Yand Gterminals to provide full fan and com-

pressor control though a single wire. The K terminal must be connected to the THP9045

Wiresaver module (see page 14). The K terminal can not be used in heat-only applications.

Note: Do not connect wires to terminals marked “Not Used.”

Français : voir la page 17 • Español: vea la página 33

Conventional systems

System-specific wiring guides

1H/1C System (2 transformers)

C24VAC common

RPower (heating) [1]

Rc Power (cooling) [1, 2]

WHeat relay

YCompressor contactor **

GFan relay **

2H/2C System (1 transformer) [6]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

WHeat relay (stage 1)

W2 Heat relay (stage 2)

YCompressor contactor (stage 1) **

Y2 Compressor contactor (stage 2)

GFan relay **

2H/2C System (2 transformers) [6]

C24VAC common

RPower (heating) [1]

Rc Power (cooling) [1, 2]

WHeat relay (stage 1)

W2 Heat relay (stage 2)

YCompressor contactor (stage 1) **

Y2 Compressor contactor (stage 2)

GFan relay **

1H/1C System (1 transformer)

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

WHeat relay

YCompressor contactor **

GFan relay **

Heat Only System [3]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

WHeat relay

Heat Only System With Fan [4]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

WHeat relay

GFan relay

Cool Only System [5]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

YCompressor contactor **

GFan relay **

See [notes] below.

** [See note on page 4]

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Remove jumper (R to Rc) for systems with two transformers. Common connection

must come from cooling transformer.

[3] In Installer Setup, set system type to Heat Only, No Fan.

[4] In Installer Setup, set system type to Conventional with zero cooling stages.

[5] In Installer Setup, set system type to Conventional with zero heat stages.

[6] In Installer Setup, set system type to Conventional with 2 heat AND 2 cool stages.

[7] In Installer Setup, set changeover valve to O or B.

[8] In Installer Setup, set to Heat Pump with 1 compressor stage and no auxiliary heat stages.

[9] In Installer Setup, set to Heat Pump with 1 compressor stage and 1 auxiliary heat stage.

[10] In Installer Setup, set to Heat Pump with 2 compressor stages and no auxiliary heat stages.

[11] In Installer Setup, set to Heat Pump with 2 compressor stages and 1 auxiliary heat stage.

[12] “L” terminal sends a continuous output when thermostat is set to Em. Heat, and acts

as a system monitor when in Heat, Cool or Off modes.

Prestige™ Installation Guide

System-specific wiring guides

Heat pump systems

2H/2C Heat Pump [10]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

O/B Changeover valve [7]

YCompressor contactor (stage 1) **

Y2 Compressor contactor (stage 2)

GFan relay **

3H/2C Heat Pump [11]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

O/B Changeover valve [7]

Aux Auxiliary heat relay

YCompressor contactor (stage 1) **

Y2 Compressor contactor (stage 2)

GFan relay **

LRelay [12]

** [See note on page 4]

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Remove jumper (R to Rc) for systems with two transformers. Common connection

must come from cooling transformer.

[3] In Installer Setup, set system type to Heat Only, No Fan.

[4] In Installer Setup, set system type to Conventional with zero cooling stages.

[5] In Installer Setup, set system type to Conventional with zero heat stages.

[6] In Installer Setup, set system type to Conventional with 2 heat AND 2 cool stages.

[7] In Installer Setup, set changeover valve to O or B.

[8] In Installer Setup, set to Heat Pump with 1 compressor stage and no auxiliary heat stages.

[9] In Installer Setup, set to Heat Pump with 1 compressor stage and 1 auxiliary heat stage.

[10] In Installer Setup, set to Heat Pump with 2 compressor stages and no auxiliary heat stages.

[11] In Installer Setup, set to Heat Pump with 2 compressor stages and 1 auxiliary heat stage.

[12] “L” terminal sends a continuous output when thermostat is set to Em. Heat, and acts

as a system monitor when in Heat, Cool or Off modes.

1H/1C Heat Pump [8]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

O/B Changeover valve [7]

YCompressor contactor **

GFan relay **

2H/1C Heat Pump [9]

C24VAC common

RPower [1]

Rc [R+Rc joined by jumper]

O/B Changeover valve [7]

Aux Auxiliary heat relay

YCompressor contactor **

GFan relay **

LRelay [12]

See [notes] below.

Français : voir la page 17 • Español: vea la página 33

System-specific wiring guides

Humidification systems

Bypass, flow-through humidifier (or

any humidifier that uses the system

transformer) [3]

Rc Power [1]

R[R+Rc joined by jumper] [2]

HUM1 Field jumper R to HUM 1 [5]

HUM2 Humidifier relay [5]

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Remove jumper (R to Rc) for systems with two transformers. Common connection

must come from cooling transformer.

[3] If using a humidifier that is wired directly to the thermostat, set humidification control

to Wired in Installer Setup.

[4] If using a wireless adapter (THM4000R) with a TrueSTEAM humidifier, set humidification

control to Wireless in Installer Setup. Connect nothing to thermostat HUM terminals.

[5] Terminals are normally open dry contacts.

[6] In Installer Setup, set dehumidification setting to Whole House Dehumidifier.

[7] In Installer Setup, set dehumidification setting to Dehumidify with Air Conditioner.

[8] Terminals are normally closed dry contacts.

[9] Equipment must include dehumidification terminal for low-speed fan.

Steam humidifier (or any humidifier with

its own transformer) [3, 4]

Rc Power [1]

R[R+Rc joined by jumper] [2]

HUM1 Humidifier relay [5]

HUM2 Humidifier relay [5]

See [notes] below.

Dehumidification systems

A/C with low-speed fan [7]

Rc Power [1]

R[R+Rc joined by jumper] [2]

DHM1 Field jumper Rc to DHM 1 [8]

DHM2 Dehumidifier relay [8, 9]

Whole house dehumidifier [6]

Rc Power [1]

R[R+Rc joined by jumper] [2]

DHM1 Dehumidifier relay [5]

DHM2 Dehumidifier relay [5]

See [notes] below.

Prestige™ Installation Guide

Press MENU.

Customize thermostat (installer options)

Press ▼to scroll down, then press INSTALLER

OPTIONS. Enter security code when prompted.

Security code is the thermostat date code

(printed on back of wallplate). Or press

MENU > EQUIPMENT STATUS to find code.

Installer Options

Press CREATE SETUP to configure all system

settings one by one.

Press VIEW/EDIT to select a specific function

and make quick changes. (See complete

list of system settings on pages 12-13.)

Press INSTALLER TEST to run system tests. You

should always test the system after

making changes to settings.

Note: Press HELP for more

information on these and

other options.

Install batteries in wireless accessories

Remote control (optional) Outdoor air sensor (optional)

Install 3 fresh AA

batteries

Install 2 fresh AA

lithium batteries

HELP

Français : voir la page 17 • Español: vea la página 33

Press MENU.

Link wireless accessories to thermostat (optional)

Press ▼to scroll down, then press INSTALLER

OPTIONS. Enter security code when prompted.

Security code is the thermostat date code

(printed on back of wallplate). Or press

MENU > EQUIPMENT STATUS to find code.

Installer Options

Press ▼to scroll down, then press WIRELESS

DEVICE MANAGER.

Wireless Device

Manager

Press ADD DEVICE to start timer, then press

buttons on wireless accessories to link

them to the thermostat (see next page).

Add Device

Timer will re-set to 15 minutes after each

accessory is linked. Thermostat will exit

link mode after 15 minutes if there is no

activity.

Press VIEW CONNECTED DEVICES to verify that all

wireless accessories have been linked to

the thermostat

Press DONE when finished.

Note: If you are installing more than one thermostat, repeat steps above and on page 10

for each thermostat.

If you are installing multiple thermostats, you must press DONE to exit “Add Device” mode

at each thermostat before linking wireless accessories to the next thermostat.

View Connected Devices

Link remote control to thermostat (optional)

1Make sure the thermostat displays

the “Add Device” timer (see page 9).

2Press CONNECT at the remote. There will

be a short delay as the remote seeks

a signal from the thermostat.

3When the screen displays

“Connected,” press DONE.

4Press NO at the next screen to save

and exit. (Or press YES and repeat

steps 1-4 to link another thermostat.)

WIRELESS SETUP

CONNECT

Link outdoor sensor to thermostat (optional)

1Make sure the thermostat displays

the “Add Device” timer (see page 9).

2Press the CONNECT button on the back

of the sensor.

3Check thermostat to verify that the

outdoor sensor is working. After

about 15 seconds, the thermostat

should display outdoor temperature

and humidity.

Press and release

Prestige™ Installation Guide

YES NO

CONNECT MORE?

The linking procedure at the remote may time

out if there is no keypress within 30 minutes.

To begin again, press and hold the blank

space (or arrow if present) in the lower right

corner of the screen until the display changes

(about 3 seconds).

Press to link to

another thermostat

Press to save

and exit

Andere Handbücher für THX9000 Prestige HD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell Chronotherm III T8602A Bedienungsanleitung

Honeywell

Honeywell THX9000 Prestige HD Bedienungsanleitung

Honeywell

Honeywell T8034C Bedienungsanleitung

Honeywell

Honeywell RTHL3550 Bedienungsanleitung

Honeywell

Honeywell S963D Bedienungsanleitung

Honeywell

Honeywell FOCUSPRO TH6320R Bedienungsanleitung

Honeywell

Honeywell SUITEPRO TB6575 Bedienungsanleitung

Honeywell

Honeywell TH114-AF-GA Bedienungsanleitung

Honeywell

Honeywell Lutron LR-HWLV-HVAC TouchPRO Wireless Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8000 Series Bedienungsanleitung

Honeywell

Honeywell TB7220U Bedienungsanleitung

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell CM67 Bedienungsanleitung

Honeywell

Honeywell CM900 Bedienungsanleitung

Honeywell

Honeywell T8000C Bedienungsanleitung

Honeywell

Honeywell CM900 Bedienungsanleitung

Honeywell

Honeywell 8160 Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell TRADELINE T8011R Bedienungsanleitung

Honeywell

Honeywell PRO 1000 Series Bedienungsanleitung

Honeywell

Honeywell TH9000 Series Bedienungsanleitung

Honeywell

Honeywell Braukmann T104F Bedienungsanleitung

Honeywell

Honeywell PRO 3000 Bedienungsanleitung

Honeywell

Honeywell Magic Stat MS3000 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung