Honeywell VisionPRO TH8000 Series Bedienungsanleitung

VisionPRO®TH8000 Series

Touch-screen Programmable Thermostat

® U.S. Registered Trademark.

Installation

Guide

69-2693-01

System Types

• Gas,oil,orelectricheatwithair

conditioning

• Warmair,hotwater,

highefficiencyfurnaces,heat

pumps,steam,gravity

• Heatonly—two-wiresystems,

power to open and close zone

valves(Series20),andnormally

open zone valves

• Heatonlywithfan

• Coolonly

• 750mVheatingsystems

This manual covers the following models

• TH8110U:For1Heat/1Coolsystems

• TH8320U:Forupto3Heat/2Coolsystems

• TH8321U:Forupto3Heat/2Coolsystemswithdehumidification

(Pull thermostat from wallplate and turn over to find model number)

Need Help?

Forassistancewiththisproductpleasevisithttp://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

This thermostat contains a Lithium battery which may contain Perchlorate material.

PerchlorateMaterial—specialhandlingmayapply,

Seewww.dtsc.ca.gov/hazardouswaste/perchlorate

Installation Guide

69-2693—01

ENGLISH

MCR29481

MCR29480

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

MERCURY NOTICE

Ifthisproductisreplacingacontrolthatcontainsmercuryinasealedtube,donot

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Grasptopandbottomofwallplate

and pull to remove from thermostat.

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

Drill3/16”holesfordrywall.

Drill7/32”holesforplaster.

Wallanchors

Wirehole Mounting screws

Must be installed by a trained, experienced technician

• Readtheseinstructionscarefully.Failuretofollowtheseinstructions

can damage the product or cause a hazardous condition.

VisionPROTM TH8000 Series

369-2693—01

ENGLISH

NOT

USED

MCR29483

NOT

USED

MCR29482

For24VACprimarypower,connectcommon

sideoftransformerto“C”terminal.

Insert supplied batteries for

primary or backup power.

Power options

Push excess wire back into the wall opening. Plug

wall opening with non-flammable insulation.

Remove factory-installed jumper

only for two-transformer systems.

Conventional Terminal Letters:

RHeating power. Connect to secondary

side of heating system transformer.

Rc Cooling power. Connect to secondary

side of cooling system transformer.

CCommon wire from secondary side of

cooling transformer (if 2 transformers).

W1st stage heat relay.

W2 2nd stage heat relay.

Y1st stage compressor contactor.

Y2 2nd stage compressor contactor.

G Fanrelay.

S1 Optional outdoor or remote sensor.

S2 Optional outdoor or remote sensor.

Heat Pump Terminal Letters:

RHeating power. Connect to secondary

side of heating system transformer.

Rc Cooling power. Connect to secondary

side of cooling system transformer.

CCommon wire from secondary side of

cooling system transformer.

Y1st stage compressor contactor.

Y2 2nd stage compressor contactor.

Aux/E

Auxiliary/Emergencyheatrelay.

G Fanrelay.

LHeat pump reset (powered continuously

whenSystemissettoEmHeat;system

monitorwhensettoHeat,CoolorOff).

O/B Changeover valve for heat pumps.

S1 Optional outdoor or remote sensor.

S2 Optional outdoor or remote sensor.

Terminal Designations Shaded areas below apply only to TH8320/TH8321.

Wiring

Installation Guide

69-2693—01

ENGLISH

Wiring guide—conventional systems

Wiring

1H/1C System (1 transformer)

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

Y Compressor contactor

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

Heat Only System

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

Heat Only System (Series 20)

Rc [R+Rc joined by jumper]

R Series20valveterminal“R”[1]

W Series20valveterminal“B”

Y Series20valveterminal“W”

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

2H/2C System (1 transformer)

Y2 Cool relay 2

W2 Heat relay 2

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay 1

Y Cool relay 1

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

1H/1C System (2 transformers)

Rc Power (cooling transformer) [1,2]

R Power (heating transformer) [1,2]

W Heat relay

Y Compressor contactor

G Fanrelay

C 24VACcommon[3,4]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

Heat Only System With Fan

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

Cool Only System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

2H/2C System (2 transformers)

Y2 Cool relay 2

W2 Heat relay 2

Rc Power (cooling transformer) [1,2]

R Power (heating transformer) [1,2]

W Heat relay 1

Y Cool relay 1

G Fanrelay

C 24VACcommon[3,4]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

See [notes] below

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Remove jumper for 2-transformer systems.

[3] Optional24VACcommonconnection.

[4] Common connection must come from cooling transformer.

Shaded areas below apply only to TH8320/TH8321.

VisionPROTM TH8000 Series

569-2693—01

ENGLISH

1H/1C Heat Pump (no auxiliary heat)

Rc Power [1]

R [R+Rc joined by jumper]

O/B Changeover valve [5]

Y Compressor relay

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

2H/1C Heat Pump (with auxiliary heat)

L Equipmentmonitor[6,7]

Aux/E Auxiliary/Emergencyheatrelay(Heat2)

Rc Power [1]

R [R+Rc joined by jumper]

O/B Changeover valve [5]

Y Compressor relay

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

2H/2C Heat Pump (no auxiliary heat)

Y2 Compressor 2 relay

Rc Power [1]

R [R+Rc joined by jumper]

O/B Changeover valve [5]

Y Compressor 1 relay

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

3H/2C Heat Pump (with auxiliary heat)

Y2 Compressor 2 relay

L Equipmentmonitor[6,7]

Aux/E Auxiliary/Emergencyheatrelay(Heat2)

Rc Power [1]

R [R+Rc joined by jumper]

O/B Changeover valve [5]

Y Compressor 1 relay

G Fanrelay

C 24VACcommon[3]

S1 Optionaloutdoor/remotesensor

S2 Optionaloutdoor/remotesensor

Shaded areas below apply only to TH8320/TH8321.

Wiring guide—heat pump systems

Wiring

See [notes] below

[1] Power supply. Provide disconnect means and overload protection as required.

[3] Optional24VACcommonconnection.

[5] O/B set to control as either Oor Bin installer setup.

[6] If Lterminalisused,24VACcommon(terminalC)must be connected.

[7] Heatpumpreset(poweredcontinuouslywhenthermostatissettoEm.Heat;systemmonitor

whensettoHeat,Cool,orOff).

Installation Guide

69-2693—01

ENGLISH

SCHEDHOLD

TUE

FAN

AUTO

Inside

6:00

SYSTEM

HEAT

DONE

0120

DONE CANCEL

6:00

SYSTEM

HEAT

MCR29486

DONE

TUE

2012

DONE

TUE

1:00

MCR29485

MCR29484

Remove tab.

Align pins on back of thermostat with

slotsinwallplate,thenpushgently

until thermostat snaps into place.

Remove tab and mount thermostat

Set date and time

Press st

to set time

Press st

to set date

Press st

to set month

Press st

to set year

Installer setup

Press DONE to save changes. Press DONE to save and exit.

1. Press SYSTEM.2. Press and hold

these two buttons

until the display

changes.

3. Changesettings

as required (see

pages7-9).

VisionPROTM TH8000 Series

769-2693—01

ENGLISH

DONE

0120

DONE

0120

MCR29486

Installer setup

SettingFunction

Press DONE to exit & save settings.

Press st to

select function

Press st to

change setting

Setup functions Settings & Options (factory default in bold)

Shaded areas below apply only to TH8320/TH8321.

0120 Year

(rst two digits)

20 (2001-2099)

21 (2100-2178)

0130 Year

(second two digits)

12 (2012)

 [Otheroptions:00-99]

0140 Month 6 [Otheroptions:1-12]

0150 Date 15 [Otheroptions:1-31]

0160 Schedule format 4 7-day programming

0 Non-programmable

0170 System type 1 1 heat/1 cool conventional

2 1heat/1coolheatpump(noaux.heat)

3 Heatonly(2-wiresystems)

4 Heatonlywithfan

5 HotwaterSeries20system(powertoopen&closezone

valves/normallyopenzonevalves)

6 Coolonly

7 2heat/1coolheatpump(withaux.heat)

8 2heat/2coolmultistageconventional

9 2heat/1coolmultistageconventional

10 1heat/2coolmultistageconventional

11 2heat/2coolheatpump(noaux.heat)

12 3heat/2coolheatpump(withaux.heat)

0180 Fan control

(heating)

0 Gas/Oil heat (equipment controls heating fan)

1 Electricfurnace(thermostatcontrolsheatingfan)

0190 Changeover valve

(O/B terminal)

0 O/B terminal controls valve in cooling

1 O/Bterminalcontrolsvalveinheating

0200 Auxiliary heat 0 Electric backup heat

1 Fossilfuelbackupheat

0210 External fossil

fuel kit

1 External fossil fuel kit controls backup heat

0 Thermostat controls backup heat (outdoor sensor required)

0220 1st stage com-

pressor cycle rate

3 Recommended for most compressors

 [Otheroptions:1,2,4,5or6CPH]

0230 2nd stage com-

pressor cycle rate

3 Recommended for most compressors

 [Otheroptions:1,2,4,5or6CPH]

Continued on next page

Installation Guide

69-2693—01

ENGLISH

Setup functions Settings & Options (factory default in bold)

Shaded areas below apply only to TH8320/TH8321.

0240 First stage heat

cycle rate (CPH=

cycles per hour)

5 Gas or oil furnaces of less than 90% efciency

1 Steam or gravity systems

3 Hotwatersystems&furnacesof90%+efciency

9 Electricfurnaces

 [Otheroptions:2,4,6,7,8,10,11,12CPH]

0250 Second stage heat

cycle rate (CPH)

5 Gas or oil furnaces of less than 90% efciency

1Steam or gravity systems

3Hotwatersystems&furnacesof90%+efciency

9Electricfurnaces

[Otheroptions:2,4,6,7,8,10,11,12CPH]

0260 Third stage heat

cycle rate (CPH)

9 Electric auxiliary heat or electric furnaces

1Steam or gravity systems

3Hotwatersystems&furnacesof90%+efciency

5Gasoroilfurnacesoflessthan90%efciency

[Otheroptions:2,4,6,7,8,10,11,12CPH]

0280 Backlight 0 Backlight on for approx. 8 seconds after keypress

1Backlightalwaysonlowintensity,fullbrightafterkey-

press(requires24VACconnection)

0300 Manual/Auto

changeover

0 Manual changeover (Heat/Cool/Off)

1Automaticchangeover(Heat/Cool/Auto/Off)

0310 Auto changeover

deadband

3 Heat/cool temperature 3°F apart (1.5°C) ** See page 11

[Otheroptions:2-9(2°Fto9°F/1.5°Cto5°C)]

0320 Temperature

display

0 Fahrenheit

1Celsius

0330 Daylight savings 2 Auto-change to daylight savings time(2007andbe-

yond,forareasthatusethenew2007DSTcalendar)

1 Auto-changetodaylightsavingstime(through2006,and

for areas that do notusethenew2007DSTcalendar)

0Daylight savings time is turned off

0340 Remote sensor 0 No remote sensor

1Outdoor sensor (display only)

2Outdoor control sensor (select heat pumps) ** See page 11

3Indoor sensor

0350 Heat pump

compressor lockout

0 No heat pump compressor lockout

[Otheroptions:15,20,25,30,35,40°F(-9.5°Cto7°C)]

0360 Heat pump

auxiliary lockout

0 No heat pump auxiliary lockout

[Otheroptions:40,45,50,55,60°F(4.5°Cto15.5°C)]

0380 Dehumidication

control

0 No dehumidication control

1Thermostatcontrolsdehumidicationwithairconditioner

** See page 11

Installer setup

Continued on next page

VisionPROTM TH8000 Series

969-2693—01

ENGLISH

Setup functions Settings & Options (factory default in bold)

0500 Furnace lter

change reminder

0 Off

1 10-day run time (about 1 month)

2 30-dayruntime(about3months)

3 60-dayruntime(about6months)

4 90-dayruntime(about9months)

5 120-dayruntime(about1year)

6 365-dayruntime(about3years)

0510 Humidier pad

change reminder

0 Off

1 90calendardays

2 180calendardays

3 365calendardays

0520 UV lamp change

reminder

0 Off

1 365calendardays

0530 Adaptive Intelligent

Recovery™

1 On ** See page 11

0 Off

0540 Program periods 4 4 program periods (Wake, Leave, Return, Sleep)

2 2programperiods(Wake,Sleep)

0580 Compressor

protection

5 5 minute compressor off time ** See page 11

 [Otheroptions:0,1,2,3or4-minuteofftime]

0600 Heat temperature

range stop

90 Max. heat temperature setting is 90°F (32°C)

 [Otheroptions:40-89°F(4.5°Cto32°C)]

0610 Cool temperature

range stop

50 Min. cool temperature setting is 50°F (10°C)

 [Otheroptions:51-99°F(10.5°Cto37°C)]

0640 Clock format 12 12-hour time (i.e., “3:30 pm”)

24 24-hourtime(i.e.,“15:30”)

0650 Extended fan

timer (heat)

0 Off

90 Fanrunsfor90secondsaftercallforheatends

0660 Extended fan

timer (cool)

0 Off

90 Fanrunsfor90secondsaftercallforcoolingends

0670 Keypad lock 0 Keypad unlocked (fully functional)

1 Partially locked (access to temperature settings only)

2 Fullylocked

0680 Heat temperature

control

2 Standard temperature control (recommended)

1 Choose if room is warmer than set temperature

3 Chooseifroomdoesnotreachsettemperature

0690 Cool temperature

control

2 Standard temperature control (recommended)

1 Choose if room is cooler than set temperature

3 Chooseifroomdoesnotreachsettemperature

0700 Temperature

display offset

0 Thermostat displays actual room temperature

 [Otheroptions:-3,-2,-1,1,2,3°Foffset(-1.5°Cto1.5°C)

0710 RESET 0 No reset

1 Reset installer options & program schedule to factory

default (only date and time settings are retained)

Installer setup

Installation Guide

69-2693—01

ENGLISH

DONE

0120

DONE

TEST

MCR29488

Duringinstallersetup,presst

repeatedlyuntil“Test”appears.

Test

number

System

status

Press st to

select test

Press st to

change status

Press DONE to terminate testing.

Shaded areas below apply only to TH8320/TH8321.

1Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Second stage compressor turns on

2Fan system 0 Fanturnsoff

1 Fanturnson

3Heating system 0 Heat and fan turn off

1 Heatturnson(fanonifFunction0170issetforheatpump,

orifFunction0180issetto“1”)**Seepage6

2 Second stage heat turns on

3 Thirdstageheatturnson

4Emergency

heating system

0 Heat and fan turn off

1 Heat and fan turn on

System test System status

CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed

duringtesting.Topreventequipmentdamage,avoidcyclingthecompressorquickly.

Installer system test

Andere Handbücher für VisionPRO TH8000 Series

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T827B Bedienungsanleitung

Honeywell

Honeywell ZIO TR70-H Bedienungsanleitung

Honeywell

Honeywell EConnect TL9160AR Bedienungsanleitung

Honeywell

Honeywell Q7300A Bedienungsanleitung

Honeywell

Honeywell Q682B Bedienungsanleitung

Honeywell

Honeywell T4 Pro Bedienungsanleitung

Honeywell

Honeywell Easy-To-See TRADELINE T841B Bedienungsanleitung

Honeywell

Honeywell T8611G Chronotherm Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell TH8110U1003 - VisionPro Thermostat Bedienungsanleitung

Honeywell

Honeywell RTH7600D Bedienungsanleitung

Honeywell

Honeywell PRO 1000 Series Bedienungsanleitung

Honeywell

Honeywell TB7200 Series Bedienungsanleitung

Honeywell

Honeywell RTH7000 Bedienungsanleitung

Honeywell

Honeywell lyric round Bedienungsanleitung

Honeywell

Honeywell Lyric Enrollment Bedienungsanleitung

Honeywell

Honeywell lyric round Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell INNCOM E529 Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell Chronotherm III Bedienungsanleitung

Honeywell

Honeywell T4360G Bedienungsanleitung

Honeywell

Honeywell RTHL2510 series Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung