Honeywell VisionPRO TH8000 Series Bedienungsanleitung

VisionPRO®TH8000 Series

Touch-screen Programmable Thermostat

® U.S. Registered Trademark.

US Patent No. 6595430, D509151 and other patents pending.

Installation

Guide

69-2389-03

This manual covers the following models

• TH8321U1097: For up to 3 Heat/2 Cool heat pump or up to 2 Heat/2 Cool

conventional systems with dehumidification, humidification, or ventilation

(Pull thermostat from wallplate and turn over to find model number)

Need Help?

For assistance with this product please visit http://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

This thermostat contains a Lithium battery which may contain Perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

Must be installed by a trained, experienced technician

• Readtheseinstructionscarefully.Failuretofollowtheseinstructions

can damage the product or cause a hazardous condition.

Installation Guide

69-2389—03

ENGLISH

MCR29481

MCR29480

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

Grasp top and bottom of wallplate

and pull to remove from thermostat.

Drill 3/16” holes for drywall.

Drill 7/32” holes for plaster.

Wall anchors

Wire hole Mounting screws

VisionPROTM TH8000 Series

369-2389—03

ENGLISH

MCR29724

E/AUX

MCR29723

E/AUX

For 24VAC primary power, connect common

side of transformer to “C” terminal.

Insert supplied batteries for

primary or backup power.

Power options

Push excess wire back into the wall opening. Plug

wall opening with non-flammable insulation.

Conventional Terminal Letters:

RSystem power. Connect to secondary

side of system transformer.

CCommon wire from secondary side of

transformer.

W1st stage heat relay.

W2 2nd stage heat relay.

Y1st stage compressor contactor.

Y2 2nd stage compressor contactor.

GFan relay.

S1/S2 Optional outdoor/remote/discharge

sensor.

U1/U1 Optional IAQ device

Heat Pump Terminal Letters:

RSystem power. Connect to secondary

side of system transformer.

CCommon wire from secondary side of

system transformer.

Y1st stage compressor contactor.

Y2 2nd stage compressor contactor.

E/Aux Auxiliary/Emergency heat relay.

GFan relay.

LHeat pump reset (powered

continuously when System is set to

Em Heat; system monitor when set to

Heat, Cool or Off).

O/B Changeover valve for heat pumps.

S1/S2 Optional outdoor/remote/discharge

sensor.

U1/U1 Optional IAQ device

Terminal Designations

Wiring

Installation Guide

69-2389—03

ENGLISH

Wiring guide—conventional systems

Wiring

1H/1C System (1 transformer)

R Power [1, 6]

W Heat relay

Y Compressor contactor

G Fan relay

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

Heat Only System

R Power [1]

W Heat relay

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

Heat Only System (Series 20)

R Series 20 valve terminal “R” [1]

W Series 20 valve terminal “B”

Y Series 20 valve terminal “W”

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

2H/2C System (1 transformer)

Y2 Cool relay 2

W2 Heat relay 2

R Power [1, 6]

W Heat relay 1

Y Cool relay 1

G Fan relay

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

Heat Only System With Fan

R Power [1, 6]

W Heat relay

G Fan relay

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

Cool Only System

R Power [1]

Y Compressor contactor

G Fan relay

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

See [notes] below

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Optional 24VAC common connection.

[6] Only works with single transformer systems.

VisionPROTM TH8000 Series

569-2389—03

ENGLISH

1H/1C Heat Pump (no auxiliary heat)

R Power [1]

O/B Changeover valve [3]

Y Compressor relay

G Fan relay

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

2H/1C Heat Pump (with auxiliary heat)

L Equipment monitor [4, 5]

E/Aux Auxiliary/emergency heat relay

R Power [1]

O/B Changeover valve [3]

Y Compressor relay

G Fan relay

C 24VAC common [2, 4]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

2H/2C Heat Pump (no auxiliary heat)

Y2 Compressor 2 relay

R Power [1]

O/B Changeover valve [3]

Y Compressor 1 relay

G Fan relay

C 24VAC common [2]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

3H/2C Heat Pump (with auxiliary heat)

Y2 Compressor 2 relay

L Equipment monitor [4, 5]

E/Aux Auxiliary/Emergency heat relay

R Power [1]

O/B Changeover valve [3]

Y Compressor 1 relay

G Fan relay

C 24VAC common [2, 4]

S1/S2 Optional outdoor/remote/discharge

sensor

U1/U1 Optional IAQ relay

Steam humidifier (or any humidifier with

its own transformer)

R Power [1]

U1 Humidifier relay [7]

Bypass, flow-through humidifier (or any

humidifier that uses the system trans-

former)

R Power [1]

U1 Field jumper R to U1 [7]

U1 Humidifier relay [7]

Whole house dehumidifier

R Power [1]

U1 Dehumidifier relay [7]

A/C with low-speed fan

R Power [1]

U1 Field jumper R to U1 [7]

U1 Dehumidifier relay [8]

Whole house powered ventilator

R Power [1]

U1 Ventilator relay [7]

Non-powered ventilator

R Power [1]

U1 Field jumper R to U1 [7]

U1 Ventilator relay

Wiring guide—heat pump systems

Wiring guide—humidification systems

Wiring guide—dehumidification systems

Wiring guide—ventilation systems

Wiring

See [notes] below

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Optional 24VAC common connection.

[3] O/B set to control as either Oor Bin installer setup.

[4] If Lterminal is used, 24VAC common (terminal C) must be connected.

[5] Heat pump reset (powered continuously when thermostat is set to Em. Heat; system monitor

when set to Heat, Cool, or Off).

[7] Terminals are normally open dry contacts.

[8] Equipment must include dehumidification terminal for low-speed fan.

Installation Guide

69-2389—03

ENGLISH

DONE

TUE

2010

DONE

TUE

1:00

MCR29746

MCR29484

Remove tab.

Align pins on back of thermostat with

slots in wallplate, then push gently

until thermostat snaps into place.

Remove tab and mount thermostat

Set date and time

Press st

to set time

Press st

to set date

Press st

to set month

Press st

to set year

Installer setup

Press DONE to save changes. Press DONE to save and exit.

SCHEDHOLD

TUE

FAN

AUTO

Inside

6:00

SYSTEM

HEAT

DONE

0120

DONE CANCEL

6:00

SYSTEM

HEAT

MCR29745

DONE

0120

1Press SYSTEM Press DONE to save & exit

2Press and hold for 5 seconds

3Change settings (see p. 7-9)

Function Setting

Press stto change

VisionPROTM TH8000 Series

769-2389—03

ENGLISH

Installer setup

Setup functions Settings & Options (factory default in bold)

0120 Year

(rst two digits)

20 (2000-2099)

21 (2101-2178)

0130 Year

(second two digits)

10 (2010)

[Other options: 00-99]

0140 Month 6 [Other options: 1-12]

0150 Date 15 [Other options: 1-31]

0160 Schedule format 4 7-day programming

0 Non-programmable

0165 Restore energy saving 0 No

1 Yes

0170 System type 1 1 heat/1 cool conventional

2 1 heat/1 cool heat pump (no aux. heat)

3 Heat only (2-wire systems)

4 Heat only with fan

5 Hot water Series 20 system (power to open & close zone

valves/normally open zone valves)

6 Cool only

7 2 heat/1 cool heat pump (with aux. heat)

8 2 heat/2 cool multistage conventional

9 2 heat/1 cool multistage conventional

10 1 heat/2 cool multistage conventional

11 2 heat/2 cool heat pump (no aux. heat)

12 3 heat/2 cool heat pump (with aux. heat)

0173 Heat Pump Type 0 Air to Air heat pump

1 Geothermal heat pump

0180 Fan control

(heating)

0 Gas/Oil heat (equipment controls heating fan)

1 Electric furnace (thermostat controls heating fan)

0190 Changeover valve

(O/B terminal)

0 O/B terminal controls valve in cooling

1 O/B terminal controls valve in heating

0200 Auxiliary heat 0 Electric backup heat

1 Fossil fuel backup heat

0210 External fossil

fuel kit

1 External fossil fuel kit controls backup heat

0 Thermostat controls backup heat (outdoor sensor required)

0220 1st stage com-

pressor cycle rate

3 Recommended for most compressors

[Other options: 1, 2, 4, 5 or 6 CPH]

0230 2nd stage com-

pressor cycle rate

3 Recommended for most compressors

[Other options: 1, 2, 4, 5 or 6 CPH]

0240 1st stage heat

cycle rate (CPH=

cycles per hour)

5 Gas or oil furnaces of less than 90% efciency

1 Steam or gravity systems

3 Hotwatersystems&furnacesof90%+efciency

9 Electric furnaces

[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]

0250 2nd stage heat cycle

rate (CPH)

5 Gas or oil furnaces of less than 90% efciency

1Steam or gravity systems

3Hotwatersystems&furnacesof90%+efciency

9Electric furnaces

[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]

0260 3rd stage heat

cycle rate (CPH)

9 Electric auxiliary heat or electric furnaces

1Steam or gravity systems

3Hotwatersystems&furnacesof90%+efciency

5Gasoroilfurnacesoflessthan90%efciency

[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]

Continued on next page

Installation Guide

69-2389—03

ENGLISH

Setup functions Settings & Options (factory default in bold)

0280 Backlight 0 Backlight on for approx. 8 seconds after keypress

1Backlight always on low intensity, full bright after keypress

(requires 24VAC connection)

0300 Manual/Auto

changeover

0 Manual changeover (Heat/Cool/Off)

1Automatic changeover (Heat/Cool/Auto/Off)

0310 Auto changeover

deadband

3 Heat/cool temperature 3°F apart (1.5°C) ** See page 11

[Other options: 2-9 (2°F to 9°F/1°C to 5°C)]

0320 Temperature

display

0 Fahrenheit

1Celsius

0330 Daylight savings 2 Auto-change to daylight saving time

0Daylight saving time is turned off

0340 Remote sensor 0 No remote sensor

1Outdoor sensor (display only)

2Outdoor sensor for control (select lockouts and frost protec-

tion) ** See page 11

3Indoor sensor

4Discharge air sensor (Required for Desert humidity control)

** See page 11

0345 Dual Fuel Heat Pump

Control **

1 Droop Control

0 No droop control

2 Droop control with aux heat lockout

0346 Dual fuel heat pump

upstage to furnace

timer **

1 1 hour

0 Off

[Other options: 0.5, 1.5, 2-6, 8, 10, 12, 14, 16 hours]

0347 Droop temperature 2 2°F (1°C)

[Other options: 2-5 (2°F to 5°F/1°C to 2.5°C)]

0350 Heat pump

compressor lockout

0 No heat pump compressor lockout

[Other options: 5–60°F (-15°C to 15.5°C)] ** See page 11

0360 Heat pump

auxiliary lockout

0 No heat pump auxiliary lockout

[Other options: 5–65°F (-15°C to 18.5°C)] ** See page 11

0371 Indoor Air Quality de-

vice on U1/U1

0 None

1 Humidication

2 Dehumidication

3 Ventilation

0372 Humidication Control 0 Off

1 Humidify with no frost protection

3 Humidify with frost protection

8 Desert humidity control in heat, off, or cool; DATS required

0374 Hum fan action 0 Humidify only while fan is on

1 Humidierforcesfanon

2 Humidify only when heat it on

3 Humidieroperatesindependentoffan

0379 Dehumidication

Control

0 None

1 Air conditioning with low speed fan

3 Wholehousedehumidication

0380 Dehumidify with air

conditioner

0 No dehumidication control

1Thermostatcontrolsdehumidicationwithairconditioner

high speed fan ** See page 11

0383 Over cooling limit 3 3°F (1.5°C)

[Other options: 1-2 (1°F to 2°F/.5°C to 1°C)]

0384 Dehumidication fan

control

0 Fan turns on with dehumidier

1 Dehumidieroperatesindependentoffan

0386 Whole house dehumid-

ication lockout

0 Off

1 On

Installer setup

** See pages 11–12

Continued on next page

VisionPROTM TH8000 Series

969-2389—03

ENGLISH

Setup functions Settings & Options (factory default in bold)

0390 Dehumidication Away

Mode

0 No

1 Yes

0391 Dehumidication Away

Mode Fan Setting

0 Fan auto

1 Fan on

2 Fan circulate

0392 Dehum. Away Mode

Low Limit Temperature

Setting

76 Low limit temperature 76°F (24°C)

[Other options: 70°F to 80°F (21°C to 27°C)]

0393 Dehum. away mode

temp. setting

85 Low limit away temperature 85°F (29°C)

[Other options: 70°F to 99°F (21°C to 37°C)]

0394 Dehum. Away Mode

Dehum. Setting

65 Away humidity level 65%

[Other options: 40% to 70%]

0400 Ventilation control 0 No ventilation

1 Vent on during all periods

2 Vent off during sleep period

3 Vent on during all periods with lockouts

4 Vent off during sleep period with lockouts

0401 Number of

bedrooms

2 Two bedrooms

[Other options: 1 to 6]

0402 Size of home 10 1,000 square feet}

[Other options: 11 to 50 (1,100 to 5,000 square feet)]

0403 Ventilation level 160 CFM (cubic feet per minute)

[Other options: (30 to 195 CFM)]

0404 Max. ventilation limit 50 50% ventilation limit

[Other options: 30% to 60% or 100%]

PMeets ASHRAE 62.2 standard

FDoes not meet ASHRAE 62.2 standard

0405 Ventilation fan action 1 Ventilation on forces fan on

2 Ventilation does not force fan on

0430 Ventilation lockout 0 Off

1 Lockout for high temperatures ** See page 11

2 Lockout for low temperatures ** See page 11

3 Lockout for high and low temperatures ** See page 11

0431 Ventilation high tem-

perature lockout

100 100°F (38°C): Settings 5°F apart (3°C)

[Other options: (90°F to 110°F/32°C to 43.5°C)]

0432 Ventilation low tem-

perature lockout

-10 -10°F (-23.5°C): Settings 5°F apart (3°C)

[Other options: (-20°F to 0°F/-29°C to -18°C)]

0500 Furnace lter

change reminder

0 Off 8 365-day run time

1 10-day run time 9 30 calendar days

2 30-day run time 10 60 calendar days

3 60-day run time 11 90 calendar days

4 90-day run time 12 120 calendar days

5 120-day run time 13 180 calendar days

6 180-day run time 14 365 calendar days

7 270-day run time

0502 Furnace lter

alert options

0 Timer counts Heat & Cool run time

1 Timer counts Cool run time only

0510 Humidier pad

change reminder

0 Off

1 90 calendar days

2 180 calendar days

3 365 calendar days

0520 UV lamp change

reminder

0 Off

1 1 year

2 2 years

Installer setup

Continued on next page

Installation Guide

69-2389—03

ENGLISH

DONE

0120

DONE

TEST

MCR29488

During installer setup, press t

repeatedly until “Test” appears.

Test

number

System

status

Press st to

select test

Press st to

change status

Press DONE to terminate testing.

Installer system test

0530 Adaptive Intelligent

Recovery™

1 On ** See page 11

0 Off

0540 Program periods 4 4 program periods (Wake, Leave, Return, Sleep)

2 2 program periods (Wake, Sleep)

0580 Compressor

protection

5 5 minute compressor off time ** See page 11

[Other options: 0, 1, 2, 3 or 4-minute off time]

0600 Heat temperature

range stop

90 Max. heat temperature setting is 90°F (32°C)

[Other options: 40-89°F (4°C to 32°C)]

0610 Cool temperature

range stop

50 Min. cool temperature setting is 50°F (10°C)

[Other options: 51-99°F (11°C to 37°C)]

0640 Clock format 12 12-hour time (i.e., “3:30 pm”)

24 24-hour time (i.e., “15:30”)

0650 Extended fan

timer (heat)

0 Off

[Other options: Fan runs for 30, 60, 90, or 120 seconds after

call for heat ends]

0660 Extended fan

timer (cool)

0 Off

[Other options: Fan runs for 30, 60, 90, or 120 seconds after

call for cool ends]

0670 Keypad lock 0 Keypad unlocked (fully functional)

1 Partially locked (access to temperature settings only)

2 Fully locked

0680 Heat temperature

control

2 Standard temperature control (recommended)

1 Choose if room is warmer than set temperature

3 Choose if room does not reach set temperature

0690 Cool temperature

control

2 Standard temperature control (recommended)

1 Choose if room is cooler than set temperature

3 Choose if room does not reach set temperature

0700 Temperature

display offset

0 Thermostat displays actual room temperature

[Other options: -3, -2, -1, 1, 2, 3°F offset (-1.5°C to 1.5°C)

0701 Humidity display offset 0 0%

[Other options: -12% to 12%]

0710 RESET 0 No reset

1 Reset installer options & program schedule to factory de-

fault (only date and time settings are retained)

Setup functions Settings & Options (factory default in bold)

Installer setup

Andere Handbücher für VisionPRO TH8000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell CT8611 Bedienungsanleitung

Honeywell

Honeywell T8424C1042 Kurzanleitung

Honeywell

Honeywell RTH2510 Series Bedienungsanleitung

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell TH114-A-240D Bedienungsanleitung

Honeywell

Honeywell ST9100C Bedienungsanleitung

Honeywell

Honeywell RTH9580 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell T8602D Bedienungsanleitung

Honeywell

Honeywell HH07AT216 Bedienungsanleitung

Honeywell

Honeywell PRO TH4110B Bedienungsanleitung

Honeywell

Honeywell T8034C Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE WEB-HMI4/C Bedienungsanleitung

Honeywell

Honeywell T6 Pro Hydronic Bedienungsanleitung

Honeywell

Honeywell Comfort Window Bedienungsanleitung

Honeywell

Honeywell TB3026B Bedienungsanleitung

Honeywell

Honeywell RTH9600WF Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell T8775 Bedienungsanleitung

Honeywell

Honeywell RTH2410B Bedienungsanleitung

Honeywell

Honeywell CT3650 Bedienungsanleitung

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell DT90E Betriebsanleitung

Honeywell

Honeywell FocusPRO TH5000 Series Bedienungsanleitung

Honeywell

Honeywell T8665A Chronotherm IV Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung