Honeywell Wi-Fi Thermostat 9000 Bedienungsanleitung

Wi-Fi Thermostat 9000

Colour Touchscreen

Installation Guide

HOME: Touch to display Home screen.

FAN: Select fan mode.

SYSTEM: Select system mode (heat/cool).

MENU: Touch to display options. Start

here to set a program schedule.

CURRENT SCHEDULE: Change temperature

setting and select temporary or permanent hold.

INDOOR CONDITIONS: Shows indoor

temperature and humidity.

CURRENT DATE AND TIME.

CURRENT STATUS: Shows system

mode (heat/cool).

OUTDOOR CONDITIONS:

Shows outdoor

temperature and humidity (post registration).

33-00235 2

Wallplate Installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

CAUTION: ELECTRICAL HAZARD

Can cause electric shock or equipment damage. Disconnect power supply before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash.

Drill 3/16" holes for drywall. Drill 7/32" holes for plaster.

Wall

anchors

Wallplate

Wire hole

Mounting

screws

Wallplate

Back of

Thermostat

3 33-00235

CCommon wire from secondary side of cooling transformer (in case of two transformers)

KOptional wire save module.

Rc Cooling power. Connect to secondary side of cooling system transformer.

RHeating power. Connect to secondary side of heating system transformer.

WO/B 1st stage heat relay. Or changeover valve for heat pumps.

Y1st stage compressor contactor.

GFan relay.

W2Aux/E 2nd stage heat relay. Or heat pump auxiliary/Emergency heat relay.

Y2 2nd stage compressor contactor.

LHeat pump system monitor.

Jumper Loop - a plug with a wire loop used to connect the Rto the RC terminals, Leave jumper loop

in place in single transformer systems. Remove (unplug) jumper loop in the two transformer systems.

Terminal Designations

Wiring

Remove

jumper loop

ONLY if you

have both R

and RC wires.

Terminal

release

Terminal

holes accept

one wire

33-00235 4

1H/1C System

(1 transformer)

Rc Power [1]

R[R+Rc joined by jumper loop]

YCompressor contactor

C24VAC common

WHeat relay

GFan relay

Heat-only System

Rc Power [1]

R[R+Rc joined by jumper loop]

C24VAC common

WHeat relay

1H/1C System

(2transformers)

Rc Power (cooling transformer) [1, 2]

RPower (heating transformer) [1, 2]

YCompressor contactor

C24VAC common [3]

WHeat relay

GFan relay

Heat-only System

with Fan

Rc Power [1]

R[R+Rc joined by jumper loop]

C24VAC common

WHeat relay

GFan relay

Wiring

Wiring Guide — Conventional Systems

NOTES

Wire specifications: Use 18 to 22-gauge thermostat wire. Shielded cable is not required.

[1] For power supply, provide a means of disconnection and overload protection.

[2] Remove jumper loop for 2-transformer systems.

[3] Common connection must come from cooling transformer.

Wiring Instructions

1. This thermostat requires a 24VAC common wire to power-up. The K terminal is available

for Wiresaver module (THP9045A1023).

2. Straighten the wire. Using a pen’s tip, hold down the terminal and gently slide the wire

into the terminal hole.

Note: Terminal hole will only accept one wire.

Jumper Loop

Cool-only System

Rc Power [1]

R[R+Rc joined by jumper loop]

YCompressor contactor

C24VAC common

GFan relay

2H/2C System

(1 transformer)

Rc Power [1]

R[R+Rc joined by jumper loop]

YCompressor contactor (stage 1)

C24VAC common

WHeat relay (stage 1)

GFan reay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers)

Rc Power (cooling transformer) [1, 2]

RPower (heating transformer) [1, 2]

YCompressor contactor (stage 1)

C24VAC common [3]

WHeat relay (stage 1)

GFan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

See [notes] below

5 33-00235

Wiring

Wiring Guide — Heat Pump Systems

NOTES

Wire specifications: Use 18 to 22-gauge thermostat wire. Shielded cable is not required.

[1] For power supply, provide a means of disconnection and overload protection.

[2] In Setup, set changeover valve to O or B.

Wiring Instructions

1. This thermostat requires a 24VAC common wire to power-up. The K terminal is available for

Wiresaver module (THP9045A1023).

2. Straighten the wire. Using a pen’s tip, hold down the terminal and gently slide the wire into

the terminal hole.

Note: Terminal hole will only accept one wire.

1H/1C Heat

Pump System

Rc Power [1]

R[R+Rc joined by jumper loop]

YCompressor contactor

C24VAC common

O/B Changeover valve [7]

GFan relay

2H/1C Heat

Pump System

Rc Power [1]

R[R+Rc joined by jumper loop]

YCompressor contactor

C24VAC common

O/B Changeover valve [2]

GFan relay

Aux/E Auxiliary/Emergency heat relay

LHeat pump system monitor

Jumper Loop

3H/2C Heat

Pump System

Rc Power [1]

R[R+Rc joined by jumper loop]

YCompressor contactor (stage 1)

C24VAC common

O/B Changeover valve [2]

GFan relay

Aux/E Auxiliary/Emergency heat relay

Y2 Compressor contactor (stage 2)

LHeat pump system monitor

See [notes] below

33-00235 6

Initial Setup

Upon initial power up, or after being reset to factory defaults, the initial thermostat options

(language, location, and system type) must be set to deﬁne the heating/cooling system.

Other options can be customised later.

Follow prompts on the screen to select appropriate options.

1. Select the language of your choice, then

touch Next.

2. Select Home or Business installation,

then touch Next.

Touch Next, or name the thermostat

location - touch THERMOSTAT and follow

the instructions.

3. Select what the thermostat will control

and touch Next.

Note:Touch the orange Help button on the

screen for more information.

4. Select the system type and touch Next.

(The system type determines other

selections for completing the initial setup.)

5. Touch Next after making selections on

each screen.

6. Touch Done on the last screen. The

thermostat displays an option to connect

to the WiFi network.

Next Next

7 33-00235

System Setup

System Setup Options (MENU > System Setup)

Screen Title Settings and Options

Language English/Français/Español.

Thermostat installed in Home/Business (Thermostat is used in a residential (default) or commercial setting).

Your thermostat location

Touch THERMOSTAT button to display the screen where you can enter a custom

name using a keypad. If you have only one thermostat, you can leave the name as

THERMOSTAT. For business installations you can check a box to display the thermostat

name on the home screen.

Your thermostat controls Select Heating or Cooling or both (default).

Your system type Select Forced Air (default), Heat Pump, or Hot Water or Steam. Each option offers

different choices on the following screens.

Your forced air heating

system type Select how your forced air system is powered: Gas/Oil (default) or Electric.

Efﬁciency of your heating

system Select Standard Efﬁciency Forced Air (default) or High Efﬁciency Forced Air.

Your heating system type If you selected Hot Water or Steam on “Your system type,” select the speciﬁc heating

system here.

Number of cooling stages Select 1 Stage (default) or 2 Stages. If you are unsure, note which wires are connected: ‘Y’

wire only (1 stage) or ‘Y’ and ‘Y2’.

Number of heating stages Select 1 Stage (default) or 2 Stages. If you are unsure, note which wires are connected: ‘W’

wire only (1 stage) or ‘W’ and ‘W2’.

Your fan control Select whether your thermostat (default) or heating system controls the fan.

Type of changeover valve If you selected ‘Heat Pump’ on “Your system type,“ select whether it uses a cooling

changeover valve (default) or heating changeover valve.

Number of heat pump

compressor stages

Select 1 Stage (default) or 2 Stages. If you are unsure, note which wires are connected: ‘Y’

wire only (1 stage) or ‘Y’ and ‘Y2’.

Your backup heat No or Yes (default)

On the home screen, touch Menu > System Setup to modify the initial system setup.

System Setup

33-00235 8

Connecting to the Wi-Fi Network

Yes

Your Network

Done

After the initial setup, walk the homeowner

through connecting to a WiFi network. Or,

refer the homeowner to the User’s Guide,

so that the homeowner can connect the

thermostat to the WiFi network later.

1. Connect the WiFi network.

Touch Yes to connect the thermostat to

the WiFi network. The screen displays the

message “Searching for wireless networks.

Please wait...” after which it displays a list

of all WiFi networks it can find.

Note: If you cannot complete this step now,

touch I’ll do it later. The thermostat will

display the home screen. Complete this

process by selecting MENU > Wi-Fi Setup.

Continue with Step 2.

2. Select the network.

2a Touch the name of the homeowner’s

network. The thermostat displays a

password page.

Note: If the home network is not shown on

the list, touch Rescan.

2b Using the keyboard enter the

password for the home network.

2c Touch Done. The thermostat displays

“Connecting to your network. Please

wait...” then shows a “Connection

Successful” screen.

2d Touch Next to display the registration

information screen.

2e Have the homeowner register the

thermostat by going to http://www.

mytotalconnectcomfort.com

Note the Thermostat’s MAC and

CRC; they’ll be needed during

registration. Or, refer the homeowner

to the User’s Guide.

Note: The Register Online screen remains

active until you complete registration and/or

touch Done.

3. For remote access, the homeowner or

end-user must register at

mytotalconnectcomfort.com

9 33-00235

Setting Advanced Preferences

1. Touch MENU. The thermostat displays a

list of options.

2. Select Preferences > Advanced

Preferences. The thermostat displays the

first screen of options that you can change.

3. On each screen, make changes as

needed, then touch Next to display new

options. Repeat this step until you have

made all changes.

4. After making all necessary changes,

touch Done to save and exit.

Preferences

Advanced Preferences

Screen Title Settings and Options

Scheduling Options

Select Non-programmable or Programmable. Programmable uses default or

customised programming to automatically raise and lower temperature settings for

different times of the day.

Temperature Indication Scale Select Fahrenheit or Celsius.

Heating and Cooling System

Changeover Select Manual or Automatic.

Number of Schedule Periods Select 2 Periods Per Day or 4 Periods Per Day.

Pre-occupancy Purge Duration * Select how long the fan will run before each occupied period: Off, 1, 2, or 3 hours.

Type of Override * Select Standard to maintain the programmed periods or Initiate Occupancy to use

energy-saving settings until a user presses Start Occupancy.

Override Duration * Select how long to maintain temperature during an override: 110 hours or No Limit.

Early Recovery for Heating * Select No to begin recovery on schedule or Yes to ramp up temperature early.

Early Recovery for Cooling * Select No to begin recovery on schedule or Yes to ramp down temperature early.

Temperature Limits Select the Minimum Cool and Maximum Heat Limit.

Keypad Lockout Select Unlocked/Partially Locked/Locked.

Clock Format Select 12 Hour or 24 Hours.

Daylight Saving Time Select Off or On. If set to On, the system will automatically change time/date to account

for daylight saving.

Indoor Display Offsets Select the number of degrees to offset indoor temperature or percentage to offset

indoor humidity.

*Available when thermostat is installed in Business mode.

33-00235 10

Troubleshooting

If you are facing difﬁculties with your thermostat, please try the following suggestions. Most

problems can be corrected easily through these.

Display is blank • Check circuit breaker and reset if necessary.

• Make sure power switch at heating and cooling system is on.

• Make sure furnace door is closed securely.

• Make sure C wire is connected.

Cannot change

system setting to

Cool

• Check at the System Setup screen “Your thermostat controls” or “Your system type” is set to

match your heating and cooling equipment.

Fan does not turn

on when heat is

required

• Check that System Setup screen “Your fan control” is set to match your heating equipment.

“Wait” appears on

the screen • Compressor protection feature is engaged. Wait for 5 minutes for the system to restart

safely, without causing damage to the compressor.

Heat pump issues

cool air in heat

mode, or warm air in

cool mode

• Check your setting for System Setup screen “Type of changeover valve” to make sure it is

properly conﬁgured for your system (see page 66).

Heating or cooling

system does not

respond

• Touch SYSTEM to set system to Heat. Make sure the temperature is set higher than the

room temperature.

• Touch SYSTEM to set system to Cool. Make sure the temperature is set

lower than the Inside temperature.

• Check circuit breaker and reset if necessary.

• Make sure power switch at heating and cooling system is on.

• Make sure furnace door is closed securely.

• If “Wait” is displayed, the compressor protection timer is on. Wait for 5 minutes for the

system to restart safely, without damaging the compressor.

Heating system

is running in cool

mode

• Check that on the System Setup screen “Your thermostat controls” or “Your system type” is

set to match your heating and cooling equipment .

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell T8131A Bedienungsanleitung

Honeywell

Honeywell PRO 1000 Series Bedienungsanleitung

Honeywell

Honeywell RTH7400D Bedienungsanleitung

Honeywell

Honeywell T8011F Bedienungsanleitung

Honeywell

Honeywell PRO TH1000 Series Bedienungsanleitung

Honeywell

Honeywell FocusPRO Bedienungsanleitung

Honeywell

Honeywell Perfect Climate Comfort Center PC8900 Bedienungsanleitung

Honeywell

Honeywell PC8900A Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Bedienungsanleitung

Honeywell

Honeywell T8112 Bedienungsanleitung

Honeywell

Honeywell PRO TH4110D Bedienungsanleitung

Honeywell

Honeywell TB7600 Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell RTH2310 Bedienungsanleitung

Honeywell

Honeywell CMT707 Bedienungsanleitung

Honeywell

Honeywell RTH7000 Bedienungsanleitung

Honeywell

Honeywell resideo TH6320U2008 Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5000 Series Bedienungsanleitung

Honeywell

Honeywell Chronotherm IV T8611G Bedienungsanleitung

Honeywell

Honeywell RTH2310 Bedienungsanleitung

Honeywell

Honeywell RTH7600 Series Bedienungsanleitung

Honeywell

Honeywell Chronotherm III T8602A Bedienungsanleitung

Honeywell

Honeywell T4360G Bedienungsanleitung

Honeywell

Honeywell CT50A Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung