Honeywell Midas S2 Bedienungsanleitung
Midas® S2
Fixed single-point extractive gas transmitter
Product Description
The Midas® S2 is a Fixed, Extractive Single-Point Gas Transmitter that
draws a sample locally or from a remote point to a sensor cartridge. A wide
range of toxic, flammable and oxygen gas sensor cartridges are available
that enable the detection of gases used or generated in semiconductor
manufacturing operations, light manufacturing environments, and
national and university labs that specialize in semiconductor processing
research.
Features & Benefits:
lHighly modular design for easy, reliable, and trouble-free installation.
lQuick replacement of cartridges and pump parts for simple
maintenance.
lSingle, smart sensor cartridge with onboard * ‘e-calibration’ certificate
l3-built-in relays (Form C) for Alarms 1, 2, and Fault
lSupportive digital communication (Modbus/TCP ethernet/Power over
Ethernet (PoE))
lKeypad interface
lFactory-calibrated sensors to reduce the need for frequent gas testing
l4-20mA analog output with fault and event reporting
lLarge, bright, and rich TFT color LCD and extensive viewing angle.
lmA communication protocols for easy connectivity and service
interaction
lRobust extractive pump system (2-year lifetime) sampling up to 100 feet
lDesigned to ensure maximum uptime while providing a delightful user
experience while using the machine and providing a low cost of
ownership for the customers
lSupportive Digital communication (Modbus / TCP Ethernet / Power over
Ethernet (PoE) )
lBlock test to ensure sampling line connection and no leakage
2
Safety
CAUTION
RISK OF INJURY AND PROPERTY DAMAGE
lTo minimize the risk of electrostatic charging, provide a suitable
ground connection, and install the equipment in such a way
that no accidental discharges occur.
lWhen Midas S2 reaches the end of its life, it should be disposed
of by local regulations.
lDo not use cleaning solvents or abrasives to clean the gas
detector.
lDo not attempt to modify the product in any way from the
manufacturer’s design or specification. Warranty will be void
and malfunction of the gas detector may result.
lUse only genuine spare parts and accessories with Midas S2.
Malfunction may result if non-standard parts are used.
lMidas® S2 is suitable for ordinary locations only and must not
be installed in hazardous locations.
lInstallation must be by the recognized standards of the
appropriate authority in the country concerned. For Europe, see
EN60079-14, EN60079-29-2, and EN61241-14. For
installations in North America, the National Electrical Code
(NFPA 70) should be strictly observed. All the appropriate local
and national regulations should be observed.
lIndoor use only.
3
Certifications
Electrical: UL 61010-1,
CSA C22.2 No.61010-1,
IEC 61010-1,
EN 61010-1
ROHS: 3(EU 2015/863)
EMC: EN 50270:2015
What's in a full box System
lMidas® S2 transmitter
lInstallation accessories (tubes, tube adaptor or LIT check valve if
ordered)
lQuick reference guide
lROHS sheet with drill template
Hardware overview
1 Display 2 Pump door latch
3 Navigation buttons 4 Sensor cartridge
5 Sensor release latch 6 Cable gland
7 Mounting holes 8 Pump module
4
User Interface overview
14
15
13
12
11
10
8
9
7
6
5
1 2 3 4
2!
1
1- Power
LED
2- Alarm 1 3- Alarm 2
4 - Fault 5 - Tips for reset faults or alarms 8- Location label
6 - Buttons
Cancel.
Reset
alarm or
fault
Accept
Power on
Up
Down
7 - Device status icons
Network
connected
Network not
connected
Password
enabled
Inhibit mode
is enabled
Flow rate
Internal pump
running
9 - Main status icons
Normal
Alarm 1
Alarm 2
Fault
Inhibit
mode
10- Gas name 11 - Gas concentration 12 - Unit
13 - Bar graph for gas
concentration display
14 - Menu 15 - Information
5
Specifications
Transmitter Dimension
Size (unit with Cartridge) 138.6 (H) x 55 (W) x 148 (D) mm (5.46 x 2.17 x
5.83 in)
Weight - Transmitter 1.03kg (2.27lb)
Weight - Sensor cartridge 34~73 g (0.075~0.161 lb) dependent on sensor
type
Power Requirements
Operating Voltage 24 VDC Nominal, -15 to +10% (20.4 to 26.4
VDC)
Operating Voltage with Power over
Ethernet (PoE)
48 VDC PoE (IEEE 802.3af compliant)
Power Consumption
Transmitter unit (normal condition) 1Typ. <5W
Transmitter unit (full load condition) 2< 12.95W (with Pyrolyzer)
Outputs
Visuals Power, alarm Fault LEDs and color TFT LCD
Relays Alarm1, Alarm2, Fault relay rated 1.0A@30VDC or
0.5A@125VAC max
Analog Sink/Source, 4-20mA
Digital Communications Modbus/TCP Ethernet/Power over Ethernet (PoE)
Display
Size/color 2.4inch IPS panel with 16.7M display color
Viewing angle 160 or higher degree viewing angle
Operation key 4-button interface keypad
Transport System
Flow Rate 500 mL/min
Sample Line Tubing 3.18mm ID X 6.35mm OD (0.125 X 0.25in)
Sample line Length Up to 30 m (100 ft) with FEP tubing
Exhaust Line Tubing 4.76 mm ID X 6.35 mm OD (0.188 X 0.25 in)
6
Exhaust Length Up to 30 m (100 ft)
Ambient Point In line air filter required
Environmental
Operating temperature 0°C to +40°C (32°F to 104°F)
0℃to 30℃(32℉to 86℉) with Pyrolyzer
Condition Indoor only
Operating atmospheric pressure 80~120Kpa
Altitude <2000m
Overvoltage Category 1
Pollution degree 2
1Normal condition: (1) No gas alarm, (2) Without tube and pressure/vacuum.
2Full load condition: (1) Gas alarm is on, (2) Maximum tubing length and pressure/vacuum
on the inlet/exhaust line.
Cleaning the system
Clean the exterior of the instrument with a soft, damp cloth. Use only
water-based (non-alcohol) cleaners. Do not use soaps, solvents, or
polishes.
7
Mount the Device
Mounting the device on a vertical flat surface.
1. Unscrew the two screws located on the main module.
2. Remove the main module by pulling it forwards off the base
module. At this time, hold the cable gland in the base module
with one hand, and with the other hand, carefully pull the main
module.
3. Unscrew the retaining screws located at the base module, and
then, remove the back plane PCB module.
8
4. Drill two holes 2.3in (58.50mm) vertically apart for 2 x round
head M4 screws, using the separately provided drill template on
the ROHS sheet.
5. Partially screw the fixings into the mounting surface.
6. Place the mounting bracket assembly over the screws, so they
pass through the mounting holes and then slide down to locate
in the slots.
7. Tighten the screws to secure the mounting bracket assembly.
9
8. Align the RJ45 socket of the power PCB module in the hole of the
mounting bracket to refit the PCB.
1
2
9. Tighten the retaining screw to secure the power PCB module.
10. Wire the device as described in the "Wiring" section.
11. Place the main module back into the base module.
12. Screw the two screws located on the main module, as identified
in Step 1.
10
Andere Handbücher für Midas S2
1
Inhaltsverzeichnis
Andere Honeywell Sender Handbücher
Honeywell
Honeywell ADEMCO 5869 Bedienungsanleitung
Honeywell
Honeywell STD110 Bedienungsanleitung
Honeywell
Honeywell SMV 3000 Bedienungsanleitung
Honeywell
Honeywell XNX Benutzerhandbuch
Honeywell
Honeywell STT850 SMARTLINE Bedienungsanleitung
Honeywell
Honeywell OELD Bedienungsanleitung
Honeywell
Honeywell ADEMCO 5818MNL Montageanleitung
Honeywell
Honeywell oneWireless XYR 6000 Bedienungsanleitung
Honeywell
Honeywell 5815-1 Bedienungsanleitung
Honeywell
Honeywell XNX Universal Transmitter Bedienungsanleitung
Honeywell
Honeywell 5816 Montageanleitung
Honeywell
Honeywell TCC800MS Bedienungsanleitung
Honeywell
Honeywell SMV 3000 Bedienungsanleitung
Honeywell
Honeywell ADEMCO 5801 Montageanleitung
Honeywell
Honeywell ADEMCO 5811 Bedienungsanleitung
Honeywell
Honeywell SmartLine ST700 Bedienungsanleitung
Honeywell
Honeywell SmartLine ST 800 Bedienungsanleitung
Honeywell
Honeywell ST 800 Series Bedienungsanleitung
Honeywell
Honeywell oneWireless XYR 6000 Bedienungsanleitung
Honeywell
Honeywell Ademco 5817CBXT Montageanleitung
Beliebte Sender Handbücher anderer Marken
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
MG
MG 10JRE Bedienungsanleitung
