Hotone Binary IR Bedienungsanleitung
DESIGN INSPIRATION
Binary IR Cab Owner's Manual
DESIG N IN SP IRATION
Congratulations on your new Hotone Binary pedal! You have just added some serious power to your pedalboard.
The Binary series lets loose versatile pro effects in compact cases. A dual-DSP powered platform and CDCM modeling system
ensure a realistic playing experience, dual-footswitch design and variable I/Os make it easy to use, and an OLED screen offers
clear, detailed display.
Binary IR Cab is an Impulse Response based cabinet simulator delivering precise legendary vintage/modern guitar/bass cab sounds
along with CDCM powered legendary studio microphone/power amp simulations.
Welcome
DESIG N IN SP IRATION
✪ Grown out of next-gen XTOMP technology
✪ Compact, easy-to-use dual footswitch IR cabinet simulator pedal
✪ Advanced CDCM modeling system ensures realistic playing experience
✪ Dual DSP-powered platform ensures high sound quality
✪ 24-bit A/D/A conversion, up to 110dB S/N ratio
✪ 100 legendary cab models
✪ 10 CDCM based legendary studio microphone simulations
✪ Detailed mic position (X, Y, Z) and room simulations
✪ 8 CDCM based power amp simulations with presence control
rd
✪ Supports 3 party IR files
✪ USB jack for firmware upgrading, loading/managing IRs with free PC/Mac software
✪ Aux in and headphone output for practicing and jamming
✪ 100 Presets
✪ Built-in OLED screen with clear display
✪ 5 transparent knobs with LEDs
✪ 9V DC power supply
Features
DESIG N IN SP IRATION
1-2. ▽/△: For selecting presets, bypass/mute, and other parameters.
3. +/- buttons: For selecting effects and adjusting parameters.
4. GLOBAL: For power amp and room control settings.
5. SAVE/EXIT button: For saving or canceling parameter changes.
6. OLED screen: Shows bank/patch numbers, setting values and other operation info.
7. VOL: Controls effect output level.
8-10. MIC POSITION X/Y/Z: Controls the mic position simulations.
11. MIC POSITION: Selects (or turns off) different microphone simulations.
12. INPUT: 1/4” (6.35mm) mono jack, for plugging in instruments or other effects.
13. AUX: 1/4” (6.35mm) stereo jack, for plugging in audio players.
Note: You can hear only left channel signal when using along with OUTPUT jack.
14. PHONES: 1/4” (6.35mm) stereo jack, for connecting headphones.
15. OUTPUT: 1/4” (6.35mm) mono jack, for connecting to audio interfaces, mixers or
other effects.
16. USB jack: Mini USB jack, for effects editing, firmware updates, and factory reset.
17. DC 9V: Plug in your power supply here (DC 9V, center negative).
Panel Introduction
DESIG N IN SP IRATION
Note: TURN ON FIRST, TURN OFF LAST. Always mute the mixer/audio interface before plugging or unplugging power jacks, cables, etc. When you're
using a mixer or an audio interface, please adjust the onboard knobs carefully to avoid signal clipping.
Connections
DESIG N IN SP IRATION
Display
Plugging in your power supply will turn on the device. The main display will come up as shown below:
1 - Current bank/patch number
2 - Indicates the cab model you’re using in current patch
DESIG N IN SP IRATION
Select a Patch
Tap either ▽/△ footswitch once to change patches (hold one footswitch to switch patches quickly). Tap △ footswitch repeatedly
to cycle through patches in the order 00, 01, 02,03, …, 99, then 00. Tap ▽ footswitch to change patches in the opposite order.
DESIG N IN SP IRATION
Bypass/Mute
Tap both ▽/△ footswitches at the same time.
To set the unit to bypass: release the footswitches within 2 seconds.
To set the unit to mute: hold the footswitches more than 2 seconds until “MUTE” appears on the screen.
Tap both ▽/△ footswitches again to go back to normal.
In Bypass/Mute status, all the LED knobs will go out.
Note: AUX IN will not be muted in MUTE status.
DESIG N IN SP IRATION
Edit
1. Adjust the parameters
Use the onboard knobs to adjust the effect parameters. The screen display will be shown as below when adjusting:
1 - Current parameter value you’re adjusting (shown: volume)
2 - Saved parameter value in the current patch (PREV. = Previous value)
The MIC POSITION X/Y controls the microphone horizontal/vertical position, set X=Y=0 to set the microphone on axis; Z controls
the distance between microphone and speaker cap.
The MIC TYPE lets you select a microphone type you like. Turn this knob to minimum to turn off microphone simulation.
x
y
0
z
x
0
DESIG N IN SP IRATION
Edit
2. Select a different effect
Use the +/- button to change to another cab sim (hold for fast changing):
The inverted bank/patch number indicates that the current patch has been edited.
Inhaltsverzeichnis
Andere Hotone Musikpedal Handbücher
Hotone
Hotone PRESS Series Kurzanleitung
Hotone
Hotone Binary Mod Bedienungsanleitung
Hotone
Hotone BINARY Bedienungsanleitung
Hotone
Hotone Binary Eko Bedienungsanleitung
Hotone
Hotone Binary Amp Bedienungsanleitung
Hotone
Hotone Ampero Bedienungsanleitung
Hotone
Hotone A STATION Bedienungsanleitung
Hotone
Hotone JOGG Montageanleitung
Hotone
Hotone Skyline Wally Bedienungsanleitung
Hotone
Hotone AMPERO II STAGE Bedienungsanleitung
Beliebte Musikpedal Handbücher anderer Marken
Matthews Effects
Matthews Effects Whaler V2 Bedienungsanleitung
Grid 1
Grid 1 Pedal Jeanie Bedienungsanleitung
Amptweaker
Amptweaker tightboost Bedienungsanleitung
Ibanez
Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung
PuzzleSounds
PuzzleSounds DR. Q ENVELOPE FILTER Bedienungsanleitung
BYOC
BYOC Analog Chorus Handbuch
