HP 3C509B ISA Bedienungsanleitung

3COM Etherlink III 3C509B ISA

10BT Network Adapter

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

General information to read before installing

• On all systems : Before installing LAN card, go into Bios setup and set PnP

OS field to NO.

• How to change LAN card configuration if needed (Advanced users only)

This is a general advisory on how to forcibly modify resources for ISA and PCI network

cards.

ISA cards:

• For ISA network adapters, start the configuration tool provided in driver

kit (See install documentation)

• Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu-

sion > reserve an IRQ for the adapter.

PCI cards:

• For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA

IRQ Resource Exclusion > reserve the IRQ for Legacy ISA.

ISA cards can’t use IRQ9

• IRQ 9 is reported as being used by ACPI during POST. This is due to ISA’s

inability to share IRQs.

• Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this:

1Install the NIC then power up the system.

2Press F2 to go to CMOS setup.

3Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation

section)

4Save the configuration settings and boot to the applicable OS.

5Follow installation steps.

Sound conflict under Win 95 on VLi8 only

• On VLi8, LAN cards cause an IRQ conflict with the embedded sound de-

vice under Win95.

• To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this:

1Install the NIC then power up the system

General information to read before installing

2Press F2 to go to CMOS setup.

3Set PNP OS to NO and reserve IRQ 5.

4Save settings and boot to applicable OS.

1 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter

Microsoft Windows 95 SR2.5

1 Installing the 3COM EtherLink III 3C509B ISA 10BT

Network Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 3.51 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and driver

disk version 6.0.

• Driver File: ELNK3ND3.SYS, version 5.26.31

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT 3.51 Server system that supports NetBEUI,

NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network

protocols.

Device Configuration

Procedure

1Power on the system and start Windows 95SR2.5.

2From the 3COM 3C509B driver disk, run PREINSTL.EXE.

3Shutdown and power down the system. With the HP Vectra turned off,

install the 3COM 3C509B network adapter into an ISA slot.

4Connect network cable media to the 3COM 3C509B network adapter.

5Power on the system and press “SHIFT-<F5>” to boot to Windows 95

command prompt.

6Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.

7Select “CONFIGURE NIC” and verify the resource settings listed above

under the heading “Device Configuration”.

8If changes are required, save those changes and exit.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 5 03 07

I/O Address 210 210 210

1 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter

Connecting to a Windows NT 3.51 Server

9Remove the 3COM 3C509B driver disk and reboot the system to Windows

95SR2.5.

10 Windows 95SR2.5 will automatically recognize the 3COM 3C509B

network adapter as “3Com 3C509B EtherLink III”.

11 Insert the 3COM 3C509B driver disk in the floppy drive and click on

“Next” from the Update Device Driver Wizard dialog box.

12 When Windows 95 detects the updated driver, “3Com EtherLink III ISA

(3C509b-TP) in PnP mode”, click on “Finish”.

13 During the Update Device Driver process, point to the appropriate file

locations (i.e. drivers disk or Windows 95 CD) to install the necessary

files. Keep newer files when a file being copied is older than the file

currently on your computer.

14 Click on “OK” when the system prompts for the computer and workgroup

names.

15 Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

NOTE According to 3COM, click on “OK” to ignore the error message indicating

“Error enumerating cards. The NIC specific DLL TCAUM509 did not find any

NICs present.”

16 Click on “YES” to restart the system when prompted.

17 Right-click on the “Network Neighborhood” icon and select “Properties”.

18 Accept the default Network Protocols and the Primary Network Logon

(Client for Microsoft Networks) as seen below and click on “OK”. (If you

do not have the required information, contact your network

administrator)

19 Client for Microsoft Networks

Client for Microsoft Networks

3Com EtherLink III ISA (3C509b-TPO) in PnP mode

3Com TCAATDI Diagnostic TDI

IPX/SPX-compatible Protocol

NetBEUI

20 Click on “OK” to accept the configuration.

21 When prompted, specify the path to your Windows 95 files.

22 Click on “Yes” when prompted to restart the system.

2 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter

Microsoft Windows 95 SR2.5

2 Installing the 3COM EtherLink III 3C509B ISA 10BT

Network Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 4.0 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and drivers

disk version 6.0.

• Driver File: ELNK3ND3.SYS, version 5.26.31

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink

IPX/SPX Compatible Transport and NWLink NetBIOS network protocols.

• Device Configuration

Procedure

1Power on the system and start Windows 95SR2.5.

2From the 3COM 3C509B driver disk, run PREINSTL.EXE.

3Shutdown and power down the system. With the HP Vectra turned off,

install the 3COM 3C509B network adapter into an ISA slot.

4Connect network cable media to the 3COM 3C509B network adapter.

5Power on the system and press “SHIFT-<F5>” to boot to Windows 95

command prompt.

6Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.

7Select “CONFIGURE NIC” and verify the resource settings listed above

under the heading “Device Configuration”.

8If changes are required, save those changes and exit.

9Remove the 3COM 3C509B driver disk and reboot the system to Windows

95SR2.5.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

2 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter

Connecting to a Windows NT 4.0 Server

10 Windows 95SR2.5 will automatically recognize the 3COM 3C509B

network adapter as “3Com 3C509B EtherLink III”.

11 Insert the 3COM 3C509B driver disk in the floppy drive and click on

“Next” from the Update Device Driver Wizard dialog box.

12 When Windows 95 detects the updated driver, “3Com EtherLink III ISA

(3C509b-TP) in PnP mode”, click on “Finish”.

13 During the Update Device Driver process, point to the appropriate file

locations (i.e. drivers disk or Windows 95 CD) to install the necessary

files. Keep newer files when a file being copied is older than the file

currently on your computer.

14 Click on “OK” when the system prompts for the computer and workgroup

names.

15 Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

16 Note: According to 3COM, click on “OK” to ignore the error message

indicating “Error enumerating cards. The NIC specific DLL TCAUM509

did not find any NICs present.”

17 Click on “YES” to restart the system when prompted.

18 Right-click on the “Network Neighborhood” icon and select “Properties”.

19 Accept the default Network Protocols and the Primary Network Logon

(Client for Microsoft Networks) as seen below and click on “OK”. (If you

do not have the required information, contact your network

administrator)

20 Client for Microsoft Networks

Client for Microsoft Networks

3Com EtherLink III ISA (3C509b-TPO) in PnP mode

3Com TCAATDI Diagnostic TDI

IPX/SPX-compatible Protocol

NetBEUI

21 Click on “OK” to accept the configuration.

22 When prompted, specify the path to your Windows 95 files.

23 Click on “Yes” when prompted to restart the system.

3 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter

Microsoft Windows 95 SR2.5

3 Installing the 3COM EtherLink III 3C509B ISA 10BT

Network Adapter

Microsoft Windows 95

SR2.5

Connecting to a NetWare

3.12 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• 3COM EtherLink III 3C509B-TP ISA 10BT network adapter and drivers

disk version 6.0.

• Driver File: ELNK3ND3.SYS, version 5.26.31

• Microsoft Windows 95 SR2.5 media.

• Novell NetWare 3.12 Server that supports IPX network protocol.

• Novell Client for Windows 95 v2.5 installation media.

Device Configuration

Procedure

1Power on the system and start Windows 95SR2.5.

2From the 3COM 3C509B driver disk, run PREINSTL.EXE.

3Shutdown and power down the system. With the HP Vectra turned off,

install the 3COM 3C509B network adapter into an ISA slot.

4Connect network cable media to the 3COM 3C509B network adapter.

5Power on the system and press “SHIFT-<F5>” to boot to Windows 95

command prompt.

6Insert the 3COM 3C509B driver disk and execute “3C5X9CFG.EXE”.

7Select “CONFIGURE NIC” and verify the resource settings listed above

under the heading “Device Configuration”.

8If changes are required, save those changes and exit.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 5 03 07

I/O Address 210 210 210

3 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter

Connecting to a NetWare 3.12 Server

9Remove the 3COM 3C509B driver disk and reboot the system to Windows

95SR2.5.

10 Windows 95SR2.5 will automatically recognize the 3COM 3C509B

network adapter as “3Com 3C509B EtherLink III”.

11 Insert the 3COM 3C509B driver disk in the floppy drive and click on

“Next” from the Update Device Driver Wizard dialog box.

12 When Windows 95 detects the updated driver, “3Com EtherLink III ISA

(3C509b-TP) in PnP mode”, click on “Finish”.

13 During the Update Device Driver process, point to the appropriate file

locations (i.e. drivers disk or Windows 95 CD) to install the necessary

files. Keep newer files when a file being copied is older than the file

currently on your computer.

14 Click on “OK” when the system prompts for the computer and workgroup

names.

15 Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

NOTE According to 3COM, click on “OK” to ignore the error message indicating

“Error enumerating cards. The NIC specific DLL TCAUM509 did not find any

NICs present.”

16 Click on “YES” to restart the system when prompted.

17 From the location of the “Novell Client for Windows 95 v.2.5” installation

files, execute “Setup.exe”.

18 Click on “Yes” to accept the License Agreement.

19 Select “Custom” installation and click on “Next”.

20 Select “Bindery (NetWare 3.x)” and click on “Next”.

21 Click on “Install” to start the installation.

22 Click on “Yes” to set the Preferred Server. (If you do not have the

required information, contact your network administrator).

23 Click on “Reboot” to complete the installation.

24 Right-click on the “Network Neighborhood” icon and select “Properties”.

25 Accept the default Network Protocols and the Primary Network Logon to

(Novell NetWare Client) as seen below and click on “OK”. (If you do not

have the required information, contact your network administrator)

Dieses Handbuch passt für folgende Modelle

Andere HP Adapter Handbücher

HP Model 744 - VME Workstation Referenzhandbuch

HP Bt500 Bedienungsanleitung

HP Model 744 - VME Workstation Montage- und Wartungsanleitung

HP P3410A - NetRAID 1M RAID Controller Bedienungsanleitung

HP P Class 733/800/866MHz / 1GHz Service-Handbuch

HP NC380T Bedienungsanleitung

HP FlexFabric 534M Bedienungsanleitung

HP 273914-B21 - Smart Array 6404/256 RAID... Bedienungsanleitung

HP Flex-10 10Gb 2-port 552M Gebrauchsanweisung

HP e3000 Bedienungsanleitung

HP NC550m Gebrauchsanweisung

HP BladeSystem Dual NC370i - Multifunction Network... Bedienungsanleitung

HP StorageWorks A7298A Bedienungsanleitung

HP StorageWorks XP10000 - Disk Array Service-Handbuch

HP 665243-B21 Bedienungsanleitung

HP TouchSmart 300-1000 - Desktop PC Bedienungsanleitung

HP 347786-B21 - 8 Internal Port SAS HBA Bedienungsanleitung

HP NC7170 Bedienungsanleitung

HP NC7771 Bedienungsanleitung

HP NC1020 Bedienungsanleitung

HP 332T Bedienungsanleitung

HP NC364m Gebrauchsanweisung

HP Integrity BL860c Bedienungsanleitung

HP ScanJet 100 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung