HP JG560A Bedienungsanleitung

Andere HP Computerhardware Handbücher

HP

HP P Class 450/500/550/600/650/700/750 Handbuch

HP

HP 3000 Series Handbuch

HP

HP Integrity rx1600 Bedienungsanleitung

HP

HP A3550A - High Availability Disk Arrays Model 20 Storage... Bedienungsanleitung

HP

HP 381513-B21 - Smart Array P800 Controller... Bedienungsanleitung

HP

HP Model 744 - VME Workstation Bedienungsanleitung

HP

HP A58 0AF Series Montageanleitung

HP

HP RDX USB 3.0 Bedienungsanleitung

HP

HP 5930-4Slot Bedienungsanleitung

HP

HP GbE2c - Blc Layer 2/3 Fiber SFP Option Anleitung zur Verwendung

HP

HP Z400 - Workstation Bedienungsanleitung

HP

HP ML570 - ProLiant - G2 Bedienungsanleitung

HP

HP HPE SimpliVity 325 Bedienungsanleitung

HP

HP Xw4600 - Workstation - 2 GB RAM Bedienungsanleitung

HP

HP 98625A Bedienungsanleitung

HP

HP D7171A - NetServer - LPr Bedienungsanleitung

HP

HP A3550A - High Availability Disk Arrays Model 20 Storage... Bedienungsanleitung

HP

HP E3473A Bedienungsanleitung

HP

HP AB479A Bedienungsanleitung

HP

HP QMH2672 Bedienungsanleitung

HP

HP NC550SFP Bedienungsanleitung

HP

HP Xw8400 - Workstation - 4 GB RAM Bedienungsanleitung

HP

HP 64751 Bedienungsanleitung

HP

HP Pavilion xl700 - Desktop PC Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Installation tools

Introduction to the opacity shield kit

The installation tools are not provided with the switch. Prepare them yourself.

Phillips

screwdriver

ESD-preventive wrist

strap

Spanner

Applicable products

Alcohol-based

cleaning pad

Two-holed mounting bracket

(2 in total)

Hex bolt

(3 in total)

M3 countersunk-head screw (used to

secure the opacity shield, 3 in total)

Tamper evidence

label (30 in total)

Opacity shield

(1 in total)

HP 5800-24G-PoE+ Switch (JC099A/JC099B)

HP 5800-24G-PoE+ TAA Switch (JG254A/JG254B)

HP 5800-48G-PoE+ Switch with 1 Interface Slot (JC104A/JC104B)

HP 5800-48G-PoE+ TAA Switch with 1 Interface Slot (JG257A/JG257B)

M4 countersunk-head screw (used to

secure the mounting brackets, 4 in total)

Installation preparation

HP 5800 switches meet the requirement of FIPS security level 2.

The installation procedures must be performed by qualified personnel.

Installing the opacity shield

Before installation, read the Compliance and Safety Manual for the compatible switch

of the opacity shield kit.

Make sure the operating temperature is not higher than 40°C (104°F).

Wear an ESD-preventive wrist strap, and make sure the wrist strap makes good skin

contact and is well grounded.

The two-holed mounting brackets are not designed to support the weight of the switch.

To mount the switch to the rack, install a rack shelf in a proper position of the rack,

place the switch on the rack shelf, and use screws to secure the two-holed mounting

brackets to the rack posts.

Applying tamper evidence labels

The mounting bracket is installed

at the port side of the chassis.

The mounting bracket is installed at

the power supply side of the chassis.

Make sure the chassis temperature is above 10°C (50°F).

Before applying tamper evidence labels, use alcohol-based cleaning pads to clean the

chassis and air dry the cohesive areas.

Apply tamper evidence labels to all field replacement units

(for example, opacity shields and interface cards), USB ports, and any M3

countersunk-head screw on an opacity shield.

The methods for applying tamper evidence labels are the same when the mounting

brackets are installed at the port side and the power supply side. In the following

example, the mounting brackets are installed at the port side.

M3 countersunk-

head screw

M4 countersunk-

head screw

Hex bolt M4 countersunk-head screw

Hex bolt

countersunk-

head screw

The methods for installing the opacity shields to an HP 5800-24G-PoE+ Switch and an

HP 5800-48G-PoE+ Switch with 1 Interface Slot are the same. This section uses an HP

5800-24G-PoE+ Switch as an example.

Only use the screws and hex bolts that are supplied in the opacity shield kit to secure

the opacity shield.

© Copyright 2015 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice.

Applying tamper evidence labels (chassis front view)

Applying tamper evidence labels (chassis rear view)

5998-3560a