HP ZX2000 Bedienungsanleitung

installing Linux®

January 2004

start here

hp enablement kit

on hp Itanium®

2-based servers

for Linux®

and workstations

Notices

The information in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held

liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection

with the furnishing, performance, or use of this material.

Warranty. A copy of the specific warranty terms applicable to your Hewlett-Packard product and replacement

parts can be obtained from your local Sales and Service Office.

Restricted Rights Legend. Use, duplication, or disclosure by the U.S. Government Department is subject to

restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause

at DFARS 252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the Commercial Computer

Software Restricted Rights clause at FAR 52.227-19 for other agencies.

HEWLETT-PACKARD COMPANY

3000 Hanover Street

Palo Alto, California 94304 U.S.A.

Reproduction, adaptation, or translation of this document without prior written permission is prohibited, except

as allowed under the copyright laws.

Trademark Notices.

Debianis a registered trademark of Software in the Public Interest, Inc.

Linuxis a registered trademark of Linus Torvalds.

Itaniumis a registered trademark of Intel.

SystemImageris a trademark of Brian Finley.

Contents

Overview............................................................................ 4

Configuring Your Console.................................................. 6

Getting Started With The HP Enablement Kit for Linux.... 12

Information to Know Before You Select a Menu Option 16

Enablement Kit Menu Options ..........................................

Executing a Menu Option.............................................................

HP Enablement Kit for Linux CD Contents....................... 25

Frequently Asked Questions/Troubleshooting................... 26

Appendix A - Using Smart Array with Linux on

Itanium® 2-based Servers.................................................. 34

Web Resources................................................................... 38

Overview

Use the HP Enablement Kit for Linux® CD with your Itanium® 2-

based system to facilitate installation or recovery of your Linux

operating system, install a golden image on one or more systems,

use tools to evaluate and repair your system, and access the Debian

GNU/Linux Installer.

Note If Linux was pre-installed on your Itanium 2-based

system, power on your machine and configure as

prompted. The functionality provided by the

installation kit has already been applied.

The enablement kit automates the following processes:

• Hardware discovery

• Disk partitioning

• Configuration of storage controllers

• Linux installation from distributor media (e.g. CD-ROM)

• Recovery of a pre-installed operating system.

This booklet provides:

• Instructions for configuring your console and getting started

with the enablement kit

• An explanation of the enablement kit’s menu options

•HP Enablement Kit for Linux CD content list

• An appendix with directions for using Smart Array with Linux

on Itanium 2-based servers

• Answers to frequently asked questions

• Web resources for Linux.

Note For latest updates to this document, please see

http://www.docs.hp.com/linux.

Configuring Your Console

The default console configuration for the Itanium 2-based system is

a local graphics display using a USB keyboard and requires no

setup.

The display screen can also be a remote serial console connected

through a serial port or through a terminal attached to a serial port.

Examples include a management processor’s serial port or a net-

work connection through a management processor that the system

treats like a serial port. If you plan to use a serial console, configure

it using the directions in this section before using the HP Enable-

ment Kit for Linux.

Note The management processor is part of the management

card. It monitors system status and can control aspects

of system operation such as power, resets,

software/firmware upgrades, and cooling.

See http://h20000.www2.hp.com/bizsupport

for documentation about the management processor.

Select manuals from the support services link on the

right side of the page. Select workstations under the

personal computing link or Itanium®-based servers

under the servers link to access the appropriate

manual.

Configuring Serial Console

Before Linux boots, all console interaction is through firmware. To

modify the default local graphics display to a serial console path,

configure a single serial port (UART) for both Console In and

Console Out in the boot manager interface. When the Linux

kernel boots, it interprets the UART as ttyS0 and sends the com-

puter output to the chosen display screen.

To begin:

1. When your system boots, select the Boot option

maintenance menu from the EFI Boot Manager

screen and press Enter.

2. From the menu, highlight Select Active Console

Output Devices and press Enter.

3. The resulting screen displays a list of UARTs and PCI devices

available for console input/output.

• UART identifiers of PNP0501 describe modes available for the

"Serial A" or "Serial 1" built-in UART.

• UART identifiers of HWP0002 describe modes available for

the "Console" UART on the management processor.

Highlight a UART and press Enter. On the same screen,

highlight Save Settings to NVRAM and press Enter. The

system prompts you to save NVRAM if you omit this step.

4. Highlight Select Active Console Input Device

from the main menu and press Enter.

5. From the list on the resulting screen, highlight the same UART

you selected as your output device and press Enter. Next

highlight Save Settings to NVRAM and press Enter.

6. To apply the changes you have selected, highlight Cold Reset

from the main menu and press Enter.

7. Select Reboot the System and OK. The firmware and serial

console are configured after reboot.

8. Complete the steps listed in the “Getting Started with the HP

Enablement Kit for Linux” section of this booklet to make a

selection from the enablement kit main menu.

Note Though the enablement kit software works with serial

as well as keyboard and VGA consoles, use a VGA

font with serial consoles for optimal screen rendering

and consistent arrow key function.

For information on Linux UART discovery order and specifying a

serial console to the Linux kernel, please see the “Frequently Asked

Questions/Troubleshooting” section in this booklet.

Reverting to VGA from Serial Console

If you’re on serial console and want to revert to VGA:

1. Login to the system

a. Bring up the elilo.conf file to edit.

b. In the append line, remove console=ttyS0 parameters in any

stanza in which you want to use VGA only and save your

changes.

Note If you are using a Debian operating system, the file is

/etc/elilo.conf. Once this file is saved, type

/usr/sbin/elilo at the prompt and press Enter.

2. Edit /etc/securetty.

a. Ensure you have an entry with tty1 for VGA functionality

before completing Step 3.

b. (Optional. Perform only if you want to remove the login

prompt from the serial port.) From the list of terminals on

which root is allowed to login, remove ttyS0 and and save.

3. Bring up the /etc/inittab file:

a. Ensure you have a getty with tty1 for VGA functionality.

b. (Optional. Perform only if you want to remove the login

prompt from the serial port.) Delete the getty that runs on the

serial port in ttyS0.

4. (Optional) If you want your system to start up X instead of text

Andere Handbücher für ZX2000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP elitebook folio g1 Bedienungsanleitung

HP Sprout Pro G2 Montageanleitung

HP Compaq Evo d500 SFF Bedienungsanleitung

HP dx6120 - Microtower PC Gebrauchsanweisung

HP FM064UT#ABA Bedienungsanleitung

HP 8000 - Elite Convertible Minitower PC Gebrauchsanweisung

HP MP9 G4 Handbuch

HP Pavilion a6410t Bedienungsanleitung

HP Z420 Series Bedienungsanleitung

HP 24 Montageanleitung

HP Visualize J280 - Workstation Handbuch

HP A1210n - Pavilion - 512 MB RAM Bedienungsanleitung

HP Pavilion a400 - Desktop PC Technisches Datenblatt

HP Presario SR1200 - Desktop PC Bedienungsanleitung

HP Compaq Elite 8300 All-in-One Bedienungsanleitung

HP dx2358 - Microtower PC Bedienungs- und Wartungshandbuch

HP s5160f - Pavilion - Slimline Bedienungsanleitung

HP 3000 Series 37 Bedienungsanleitung

HP EliteDesk 700 G1 Small Form Factor Bedienungs- und Wartungshandbuch

HP Pro G2 SFF Bedienungsanleitung

HP VECTRA XW Bedienungsanleitung

HP ProDesk 400 G1 Bedienungsanleitung

HP dx2420 - Microtower PC Bedienungsanleitung

HP TV Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung