HP ProLiant DL100 G2 DPSS Bedienungsanleitung

*372017-003*

This document is for the person who installs, administers, and

troubleshoots servers and storage systems. HP assumes that you are

qualified in servicing computer equipment, and trained in recognizing

hazards in products with hazardous energy levels.

Operating System

The HP ProLiant DL100 G2 Storage Server is preloaded with the

Windows® Storage Server 2003 operating system. Prior to power up,

deployment instructions found in the HP ProLiant Storage Server user

guide should be followed to enable the successful configuration of the

storage server.

Product Documentation

Contents

1DL100 G2 Storage Server

2Documentation CD

3Quick Restore CD

4Service Release CD

5Bezel

6Power cord

7Slide rail assembly1

8Thumbscrew brackets and screws

Front and Rear Views

1Slim DVD-ROM

2Individual HDD status LED

32 USB ports

4Overall HDD activity LED

5Overall HDD fault LED

6NIC LEDs

7UID LED

8Power LED

9UID button

10 Power button

11 HDD bays (0-3)

1Dual USB port

2PS/2 mouse port

3NIC connectors (RJ45)(1-2)

4UID LED

5Low profile, half length PCI-X slot

6Full height, full length PCI-X slot

7AC power connector

8PS/2 keyboard port

9Serial port

10 D-sub VGA port

Warnings and Cautions

WARNING! Before you begin, make sure that the rack is

sufficiently stable. If provided, lower the rack leveler feet and make

sure any required stabilizers are installed. If provided, extend the rack

anti-tip device. Failure to extend the anti-tip device could result in

personal injury or damage if the rack tips over.

CAUTION: Make sure that the rack and all equipment mounted

in the rack have a reliable ground connection. Verify that the total

current of the rack components does not exceed the current rating of

the power distribution unit or outlet receptacles.

Rack planning procedures

The rack resource kit ships with all HP branded or Compaq branded

9000, 10000, and H9 series racks. For more information on the

content of each resource, see the rack resource kit documentation.

If you intend to deploy and configure multiple servers in a single rack,

refer to the white paper on high-density deployment at the following

HP web site:

www.hp.com/products/servers/platforms

Installation Instructions Rack installation

instructions

User Guide Requirements and

configuration options

Administration Guide Provides administrative

and procedural

instructions to manage

the storage server

Documentation CD Contains electronic ver-

sions of:

Administration guide

User guide

Rack installation

instructions

HP Warranty fulfillment document Provides instructions to

obtain a printed

warranty

HP Important Safety Information booklet Safety information for

HP storage, power,

networking and rack

products

5200a

1. Slide rail assemblies vary. The click-and-snap assemblies hook onto the

rack. The hardware-mounted assemblies attach to the rack using supplied

screws, star washers, and locator washers.

10699

3 4 8 10

5 7 9

1 2

10700

8 9

531 42 6 7

HP ProLiant

DL100 G2 Storage Server

installation instructions

Windows® is a U.S. registered trademark of Microsoft Corporation.

Third edition September 2005

Product names mentioned herein may be trademarks of their respective

companies as reflected by an associated footnote.

The information in this document is subject to change without notice.

www.hp.com

*372017-003*

This document is for the person who installs, administers, and

troubleshoots servers and storage systems. HP assumes that you are

qualified in servicing computer equipment, and trained in recognizing

hazards in products with hazardous energy levels.

Operating System

The HP ProLiant DL100 G2 Storage Server is preloaded with the

Windows® Storage Server 2003 operating system. Prior to power up,

deployment instructions found in the HP ProLiant Storage Server user

guide should be followed to enable the successful configuration of the

storage server.

Product Documentation

Contents

1DL100 G2 Storage Server

2Documentation CD

3Quick Restore CD

4Service Release CD

5Bezel

6Power cord

7Slide rail assembly1

8Thumbscrew brackets and screws

Front and Rear Views

1Slim DVD-ROM

2Individual HDD status LED

32 USB ports

4Overall HDD activity LED

5Overall HDD fault LED

6NIC LEDs

7UID LED

8Power LED

9UID button

10 Power button

11 HDD bays (0-3)

1Dual USB port

2PS/2 mouse port

3NIC connectors (RJ45)(1-2)

4UID LED

5Low profile, half length PCI-X slot

6Full height, full length PCI-X slot

7AC power connector

8PS/2 keyboard port

9Serial port

10 D-sub VGA port

Warnings and Cautions

WARNING! Before you begin, make sure that the rack is

sufficiently stable. If provided, lower the rack leveler feet and make

sure any required stabilizers are installed. If provided, extend the rack

anti-tip device. Failure to extend the anti-tip device could result in

personal injury or damage if the rack tips over.

CAUTION: Make sure that the rack and all equipment mounted

in the rack have a reliable ground connection. Verify that the total

current of the rack components does not exceed the current rating of

the power distribution unit or outlet receptacles.

Rack planning procedures

The rack resource kit ships with all HP branded or Compaq branded

9000, 10000, and H9 series racks. For more information on the

content of each resource, see the rack resource kit documentation.

If you intend to deploy and configure multiple servers in a single rack,

refer to the white paper on high-density deployment at the following

HP web site:

www.hp.com/products/servers/platforms

Installation Instructions Rack installation

instructions

User Guide Requirements and

configuration options

Administration Guide Provides administrative

and procedural

instructions to manage

the storage server

Documentation CD Contains electronic ver-

sions of:

Administration guide

User guide

Rack installation

instructions

HP Warranty fulfillment document Provides instructions to

obtain a printed

warranty

HP Important Safety Information booklet Safety information for

HP storage, power,

networking and rack

products

5200a

1. Slide rail assemblies vary. The click-and-snap assemblies hook onto the

rack. The hardware-mounted assemblies attach to the rack using supplied

screws, star washers, and locator washers.

10699

3 4 8 10

5 7 9

1 2

10700

8 9

531 42 6 7

HP StorageWorks

DL100 G2 Storage Server

installation instructions

Windows® is a U.S. registered trademark of Microsoft Corporation.

Third edition September 2005

Product names mentioned herein may be trademarks of their respective

companies as reflected by an associated footnote.

The information in this document is subject to change without notice.

www.hp.com

1Slide rail installation

NOTE: Depending on the rail kit provided, your slide rail

assemblies may vary slightly from those in the following illustrations.

1. Install the slide rails to the rack as shown.

• For hardware-mounted rails (A), mount the rails onto the rack

using the supplied screws and star washers. For square-hole

racks, use the provided locator washers.

• For click-and-snap rails (B), hook the rails onto the rack. At both

ends of the rail, push the outer spring latch 1, and then slide

the spring mechanism toward the rail end until the rail is

secure 2.

IMPORTANT: For hardware-mounted assemblies, HP

recommends leaving the screws loose until the server is completely

installed. This eases installation by preventing binding of the server in

the rack.

2. Locate the inner slide rails:

• On hardware-mounted assemblies, remove the inner slide rails

from the outer slide rails. To do so, extend the inner slide rails

from the front of the rack until they lock in place. Then, press the

inner slide lock down, as shown, and pull the inner slide rails

straight out.

• On click-and-snap assemblies, the inner slide rails arrive

separately from the outer slide rails.

2Server preparation

1. Attach the two thumbscrew brackets to the server using the supplied

bracket screws, as shown 1.

2. Attach a slide rail (lock facing out) to each side of the server, insert

the slide rail screws through the slide rails, and then tighten, as

shown 2.

3. Attach the bezel 3to the thumbscrew brackets, and then lock bezel

to server (if desired).

3Server installation

1. With the outer slide rails extended a short distance from the rack,

insert the inner slide rails (with the server attached) into the outer

slide rails, as shown 1. Press the inner slide lock 2, and then push

the server all the way into the rack, making sure that the inner slide

rails lock into place.

2. Slide the server in and out of the rack several times, allowing the

rails to position properly 1.

3. Lock the server in place using the thumbscrews 2.

4. If installing a hardware-mounted rail assembly, tighten all the slide

rail screws.

4Cables

1. Install the cables.

2. Plug the power cord into the rack power strip.

5201

10685

5202

5203A

5204

5205

1Slide rail installation

NOTE: Depending on the rail kit provided, your slide rail

assemblies may vary slightly from those in the following illustrations.

1. Install the slide rails to the rack as shown.

• For hardware-mounted rails (A), mount the rails onto the rack

using the supplied screws and star washers. For square-hole

racks, use the provided locator washers.

• For click-and-snap rails (B), hook the rails onto the rack. At both

ends of the rail, push the outer spring latch 1, and then slide

the spring mechanism toward the rail end until the rail is

secure 2.

IMPORTANT: For hardware-mounted assemblies, HP

recommends leaving the screws loose until the server is completely

installed. This eases installation by preventing binding of the server in

the rack.

2. Locate the inner slide rails:

• On hardware-mounted assemblies, remove the inner slide rails

from the outer slide rails. To do so, extend the inner slide rails

from the front of the rack until they lock in place. Then, press the

inner slide lock down, as shown, and pull the inner slide rails

straight out.

• On click-and-snap assemblies, the inner slide rails arrive

separately from the outer slide rails.

2Server preparation

1. Attach the two thumbscrew brackets to the server using the supplied

bracket screws, as shown 1.

2. Attach a slide rail (lock facing out) to each side of the server, insert

the slide rail screws through the slide rails, and then tighten, as

shown 2.

3. Attach the bezel 3to the thumbscrew brackets, and then lock bezel

to server (if desired).

3Server installation

1. With the outer slide rails extended a short distance from the rack,

insert the inner slide rails (with the server attached) into the outer

slide rails, as shown 1. Press the inner slide lock 2, and then push

the server all the way into the rack, making sure that the inner slide

rails lock into place.

2. Slide the server in and out of the rack several times, allowing the

rails to position properly 1.

3. Lock the server in place using the thumbscrews 2.

4. If installing a hardware-mounted rail assembly, tighten all the slide

rail screws.

4Cables

1. Install the cables.

2. Plug the power cord into the rack power strip.

5201

10685

5202

5203A

5204

5205

Andere Handbücher für ProLiant DL100 G2 DPSS

Inhaltsverzeichnis

Andere HP Netzwerkspeicherserver Handbücher

HP ProLiant ML110 G5 Bedienungsanleitung

HP ML350 - ProLiant - G2 Bedienungsanleitung

HP MediaSmart EX495 Anleitung zur Verwendung

HP LeftHand P4000 - SAN Solutions Bedienungsanleitung

HP NetStorage 6000 Gebrauchs- und Pflegehandbuch

HP StorageWorks NAS e7000 v2 Bedienungsanleitung

HP 3PAR StoreServ 7000 Bedienungsanleitung

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Bedienungsanleitung

HP ML110 - ProLiant G5 2TB Storage Server NAS Anleitung zur Verwendung

HP X1800sb Gebrauchsanweisung

HP J3278B - SureStore CD-ROM Server/Tower 7 NAS... Bedienungsanleitung

HP ProLiant ML30 Gen10 Bedienungsanleitung

HP ML110 - ProLiant G5 2TB Storage Server NAS Bedienungsanleitung

HP J3278B - SureStore CD-ROM Server/Tower 7 NAS... Bedienungsanleitung

HP 345646-001 - StorageWorks NAS 2000s External Storage... Bedienungsanleitung

HP NetStorage 6000 Gebrauchs- und Pflegehandbuch

HP NetStorage 6000 Bedienungsanleitung

HP ProLiant ML310 G3 1TB Bedienungsanleitung

HP ML110 - ProLiant G5 2TB Storage Server NAS Bedienungsanleitung

HP ProLiant ML350 G4p Bedienungsanleitung

HP ProLiant DL180 G Gebrauchsanweisung

HP StorageWorks NAS 500s Service-Handbuch

HP NetStorage 6000 Bedienungsanleitung

HP NAS 4000s Bedienungsanleitung

Beliebte Netzwerkspeicherserver Handbücher anderer Marken

Seagate

Seagate U10 ST320423A Bedienungsanleitung

Synology

Synology RackStation RS816 Handbuch

D-Link

D-Link ShareCenter Pro DNS-1200-05 Bedienungsanleitung

Avid Technology

Avid Technology VideoRAID ST Sicherheitsleitfaden

Western Digital

Western Digital My Cloud Home Duo Bedienungsanleitung

PrimeArray

PrimeArray 4xxx Bedienungsanleitung

Buffalo

Buffalo TeraStation WSS WSH5010N6 Bedienungsanleitung

Planex

Planex MZK-NAS01SG Bedienungsanleitung

Intel

Intel SS4000-E - Entry Storage System NAS Server Bedienungsanleitung

Synology

Synology RS2212+ Bedienungsanleitung

Allnet

Allnet ALL69000 Bedienungsanleitung

Adaptec

Adaptec 5325301580 Bedienungsanleitung

Motorola

Motorola EXORdisk II Bedienungsanleitung

Sony

Sony XDAAI1PK Bedienungsanleitung

Cisco

Cisco Linksys NAS200 Original Betriebsanleitung

Sans Digital

Sans Digital MR4UT6G Bedienungsanleitung

AIC

AIC FB128-LX Bedienungsanleitung

Dell

Dell PowerVault NX3500 Gebrauchsanweisung