HP HP3000/9x9KS Kurzanleitung
I/O Upgrade Manual
HP3000/9x9KS and HP9000 K-Class
Enterprise Servers
A2375-90027
Printed in U.S.A. January 1998
Edition 6 E0198
ii
Legal Notices
Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not
be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages
in connection with the furnishing, performance, or use of this material.
Warranty. A copy of the specific warranty terms applicable to your Hewlett-Packard product and
replacement parts can be obtained from your local Sales and Service Office.
Restricted Rights Legend. All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent of Hewlett-Packard
Company. The information contained in this document is subject to change without notice.
Use, duplication or disclosure by the U.S. Government is subject to restrictions as set forth in
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS
252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the Commercial Computer
Software Restricted Rights clause at FAR 52.227-19 for other agencies.
Use of this manual and flexible disk(s), tape cartridge(s), or CD-ROM(s) supplied for this pack is
restricted to this product only. Additional copies of the programs may be made for security and back-up
purposes only. Resale of the programs in their present form or with alterations, is expressly prohibited.
Copyright Notices. ©copyright 1983-97 Hewlett-Packard Company, all rights reserved.
Reproduction, adaptation, or translation of this document without prior written permission is prohibited,
except as allowed under the copyright laws.
iii
Printing History
New editions of this manual incorporate all material updated since the previous edition. The manual
printing date and part number indicate its current edition. The printing date changes when a new edition
is printed. (Minor corrections and updates which are incorporated at reprint do not cause the date to
change.) The manual part number changes when extensive technical changes are incorporated.
February 1995..................................................................................................................... Edition 1
September 1995.................................................................................................................. Edition 2
January 1996 ....................................................................................................................... Edition 3
June 1996 ............................................................................................................................ Edition 4
July 1997 ............................................................................................................................Edition 5
January 1998........................................................................................................................ Edition 6
Change Narrative
• Edition 6 technical changes include the addition of HP9000/K380/K580 information throughout the manual.
• Minor changes and updates were also incorporated.
Reader Comments
Reader Comments. We welcome your comments about our documentation. If you have editorial
suggestions or recommend improvements for this document, please write to us. You can reach us
M/S 5657, Hewlett-Packard Company, 8000 Foothills Blvd., Roseville, CA 95747-5657 USA. Please
include the following information in your message:
• Title of the manual you are referencing.
• Manual part number (from the title page).
• Edition number or publication date (from the title page).
• Your name.
• Your company’s name.
SERIOUS ERRORS, such as technical inaccuracies that may render a program or a hardware device
inoperative, should be reported to your HP Response Center or directly to a Support Engineer.
iv
1-1
1I/O Upgrade
This I/O Upgrade manual provides information for expanding the I/O capability of the HP 3000/9x9KS
and HP 9000/K2x0, K3x0, K4x0, and K5x0 computer systems.
Introduction
The Upgrades available are shown in Table 1-1.
Table 1-1 Available Upgrades
HP-HSC I/O upgrades are achieved by the addition of an expansion card with two or four slots.
However, two and four slot Primary I/O expansion cards cannot be installed in the same computer. The
HP9000/K5x0 systems allow the addition of a secondary I/O expansion.
a. HP9000/K5x0 only
Available Upgrades Computer Systems
Upgrade
Type Product
No. HP3000/
9x9KS HP9000/
K4x0 HP9000/
K3x0/K5x0
Add 4 HP-PB slots A3185A Yes Yes No
Add 2 Primary
HP-HSC slots A3186A No Yes No
A3696A No No Yes
Add 4 Primary
HP-HSC slots A2990A No Yes No
A3695A No No Yesa
Add 4 Secondary
dual-bus HP-HSC
slots
A3694A No No Yesa
1-2
I/O Upgrade
Electrostatic Discharge
Backplane Card Slot Color Codes
The following color bars appear above the slots on the system backplane:
Table 1-2 Color Codes
I/O and processor cards have matching color codes to assist in correctly matching the cards to the right
slots.
Electrostatic Discharge
Computer systems contain assemblies and components that are sensitive to electrostatic discharge
(ESD). Carefully observe the precautions listed in this section and use the ESD wrist strap, ESD sheet,
and ESD foam pad provided in the ESD kit (part number A3024-80004). The following precautions can
significantly reduce the risk of system failure or component damage due to ESD.
• Always wear a grounded wrist strap when working around a system or handling any assembly, component, or
card.
• Treat all assemblies, components, cards, and connections as sensitive.
• When unpacking cards or components to the system, keep the item in it's conductive bag until it is ready to be
installed.
• Keep body movement to a minimum, this generates static electricity that causes ESD.
• Avoid working in carpeted areas.
• Try to select a work area where potential static sources are minimized.
a. HP9000/K3x0/K5x0 systems.
b. HP9000/K5x0 systems only.
Color Slot
Yellow HP-PB0
Green HP-PB1
Blue Core/IO
Orange HP-HSC Expansion I/O (primary)
Split Magenta/PurpleaOptional HP-HSC Secondary I/Obor additional Processor slots.
Purple Processor slots.
1-3
I/O Upgrade
Tools required
Anti-Static Wrist Strap
The anti-static wrist strap is a bracelet like strip that goes around either wrist. The other end of the strap
connects to a convenient metal surface on the computer cabinet.
Anti-Static Mat
The anti-static mat can be either the conductive bag, the ESD sheet, or the ESD foam pad. The anti-static
mat does not have to be connected to the cabinet. It should be placed close to the computer while
performing the upgrade tasks.
Tools required
To accomplish the upgrade procedures to the computer the following tools are required:
• A Torx #10 driver. (This is the preferred tool)
• A flat blade screw driver. (this can be used if a Torx driver is not available)
• A3204-80004 ESD Kit
• Chip extraction tool (HP part number 8710-1982)
• Flashlight or alternate light source (recommended but not required)
1-4
I/O Upgrade
HP-PB Upgrade
HP-PB Upgrade
CAUTION The procedures outlined in the HP-PB UPGRADE section are to be performed by trained
and experienced Field Service personnel. If you have not received Hewlett Packard Service
Training or do not have the equivalent hardware experience, DO NOT attempt these
procedures.
To expand the HP-PB I/O capability of the computer, the Programmable Array Logic (PAL) chip on the
system board has to be changed. The PAL chip is accessed from the back of the computer and is located
in the same place for either the HP 3000 or the HP 9000 systems. Figure 1-1, item 1, shows the PAL
location with all components removed from the back of the computer.
Figure 1-1 PAL Chip Location
HP-PB Upgrade Procedures
Be sure to observe all ESD precautions. The suggested time to perform the upgrade is at a non-peak
usage for the computer. To accomplish the upgrade, perform the following steps:
1. Log Off all users and stop all active applications that may be running.
2. Perform a system backup of the entire Operating System and data base. If this is not feasible, perform a backup
of the data base. (This should be done at a scheduled interval as common practice for protecting any new data or
changes to the existing data base.)
3. Perform a system shutdown. Enter "/etc/shutdown -h" at the prompt.
4. Turn the computer key switch to the STANDBY position.
5. At the rear of the computer, unplug the power cord.
6. Loosen the four (two top and two bottom) captive screws on the power supply, then grasp the extractor levers
and pull them out.
1-5
I/O Upgrade
HP-PB Upgrade
NOTE On HP9000/K250/K260/K450/K460/K370/K380/K570/K580 and 979KS systems, the
power supply has six captive screws, three each on the top and bottom.
7. Grasp the handle on the power supply and pull it out of the computer.
CAUTION The power supply may weigh as much as 26.5 lbs (12 kg). Be careful lifting it and be
careful where you put it down.
8. Remove the back CPU cover plate by loosening the two (one top and one bottom) captive mounting screws and
pulling the cover plate away.
9. Carefully remove the CPU cards (if they are present) and place them on the anti-static sheet.
10. Reach into the computer and insert the tapered end of the extraction tool (8710-1982) into one of the extraction
slots (Figure 1-2, item 1) in the PAL socket (U30).
Figure 1-2 PAL Chip Socket
11. Gently pry up on the corner of the PAL chip (each side) until you can safely remove it. Be careful not drop the
chip inside the computer cabinet, because it could fall into the fan compartment.
12. Match the beveled corner (Figure 1-2, item 2) of the PAL socket to the beveled corner of the PAL chip
(A2375-81801).
13. Place the PAL chip into the socket and gently push until it fully seats.
14. Remove the HP-PB1 cover plate, and install the HP-PB card guides (5062-9367) and single high bulkheads
(5062-3343).
15. Replace the power supply and CPU card(s) that were removed.
16. Connect the power cord to the rear of the computer.
17. Turn the computer key switch to the ON position.
18. Observe the Front Panel Display and Console for any error or fault (FLT) messages.
Figure 1-3 shows the added HP-PB I/O slots. The four slots under the HP-PB 1 title are the additional
I/O slots. Any supported HP-PB I/O cards can now be installed into the computer.
1-6
I/O Upgrade
HP-PB Upgrade
Figure 1-3 HP-PB I/O Slot Locations - HP9000/K4x0 System
Although Figure 1-3 shows an HP 9000/K4x0 computer, the HP-PB locations are the same for the HP
3000/ 9x9KS computer. The Slot path addresses are also the same as shown in Table 1-3.
Table 1-3 HP-PB Address Path
Location Device Type Address Path
HP-PB 1, slot 1 HP-PB I/O card 10/16/4 (device addr.)
HP-PB 1, slot 2 HP-PB I/O card 10/16/8(device addr.)
HP-PB 1, slot 3 HP-PB I/O card 10/16/12(device addr.)
HP-PB 1, slot 4 HP-PB I/O card 10/16/16(device addr.)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere HP Server Handbücher
HP
HP t5335 - Thin Client Bedienungsanleitung
HP
HP T5720 - Compaq Thin Client Bedienungsanleitung
HP
HP Apollo 4200 Gen10 Montageanleitung
HP
HP t5400 - Thin Client Montage- und Bedienungsanleitung
HP
HP ProLiant DL580 Gen9 Handbuch
HP
HP ProLiant DL985 Bedienungsanleitung
HP
HP ProLiant SL4545 G7 Handbuch
HP
HP ProLiant ML310e Gen Montageanleitung
HP
HP ProLiant DL380 G6 Server Bedienungsanleitung
HP
HP ProLiant DL360p Gebrauchsanweisung
HP
HP Integrity rx2660 Bedienungsanleitung
HP
HP ProLiant ML310e Bedienungsanleitung
HP
HP 3020 Bedienungsanleitung
HP
HP ProLiant DL140 - G2 Server Bedienungsanleitung
HP
HP DL360 - ProLiant - Photon Bedienungs- und Sicherheitshinweise
HP
HP D7171A - NetServer - LPr Bedienungsanleitung
HP
HP 3020 Installationsanleitung
HP
HP 127695-B21 - Smart Array 431 RAID Controller Bedienungsanleitung
HP
HP ProLiant ML150 G6 Handbuch
HP
HP DL385 - ProLiant - G5 Gebrauchsanweisung
