HP VS160 - StorageWorks DLT Tape Drive Bedienungsanleitung

Internal drives - contents

Pre-Installation

Before you start page 3

Backup software and drivers page 5

Using the CD-ROM page 7

Installing the tape drive

Step 1: Check the SCSI connection page 9

Step 2: Check the drive’s SCSI ID page 11

Step 3: Prepare the mounting bay page 13

Step 4: Attach mounting hardware page 15

Step 5: Install the drive page 17

Step 6: Attach power and SCSI cables page 19

Step 7: Secure the drive page 21

Step 8: Verify installation page 23

Using the tape drive

Your HP StorageWorks VS160 tape drive page 25

Use the correct media page 27

Diagnostic tools page 30

Optimizing performance page 31

Troubleshooting page 33

Understanding the LEDs page 38

Problems with cartridges page 42

Other sources of information page 43

Replacing your tape drive page 44

dltvs160_master.fm Page 1 Monday, November 22, 2004 10:30 AM

December 2004

Part Number: A7569-96001

Hewlett-Packard Company makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and fitness for a

particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use

of this material.

This document contains proprietary information, which is protected by copyright. No part of

this document may be photocopied, reproduced, or translated to another language without

the prior written consent of Hewlett-Packard. The information contained in this document is

subject to change without notice.

Microsoft®, MS-DOS®, MS Windows®, Windows®and Windows NT®are U.S.

registered trademarks of Microsoft Corporation.

DLTtape, the DLTtape logo, Super DLTtape and the Super DLTtape logo are trademarks of

Quantum Corporation registered in the U.S.A. and other countries.

Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions

contained herein. The information is provided ”as is” without warranty of any kind and is

subject to change without notice. The warranties for Hewlett-Packard Company products are

set forth in the express limited warranty statements for such products. Nothing herein should

be construed as constituting an additional warranty.

Printed in the U.K.

Product Details

Write your tape drive details here so you can find them easily if you need them. The model name is on the

front of the drive and the product and serial numbers are on a label on the bottom of the drive.

Model (type of drive):

Model (number):

Serial (number):

Date purchased/installed:

SCSI ID:

dltvs160_master.fm Page 2 Monday, November 22, 2004 10:30 AM

Before you start

The HP StorageWorks VS160 tape drive is a high-capacity, high-performance streaming tape

drive. It is installed into a spare drive bay in your server. Before starting to install your tape

drive, you should consider the following.

Which operating systems are supported?

HP StorageWorks VS160 drives can be connected to servers running under Windows®.

Refer to the “HP StorageWorks Tape Software Compatibility” topic on our World Wide Web

site (www.hp.com/go/connect) for more information about the operating system versions

that are supported.

.How do I the connect the tape drive to my server’s SCSI bus?

Your tape drive is attached to the SCSI bus of the host server via a spare connection on the

internal SCSI ribbon cable. You will need a properly installed and configured SCSI host bus

adapter (HBA) or a built-in SCSI controller on your server. For optimum performance your tape

drive should be connected to an Ultra 160 or Ultra 320 host bus adapter or SCSI controller

using a correctly terminated, LVDS-compatible ribbon cable with a spare 68-pin, high-density

(HD), wide SCSI connector.

For most servers we recommend that you use the terminated SCSI ribbon cable supplied with

the drive, see page 19. We also recommend that the drive is the only device on the SCSI bus.

Do not connect more than two tape drives per SCSI controller. Do not attach the drive to the

same SCSI bus as your disk drive or to a RAID controller, unless it is a ProLiant server with a

Smart Array 6i RAID controller.

Why is the SCSI bus type important?

The SCSI bus type determines the speed at which data can be transferred between devices on

the bus and the maximum length of cable that can be used. HP StorageWorks VS160 tape

drives are high performance Ultra 160 SCSI devices with a maximum burst transfer speed of

160 MB/second. To benefit from this level of performance, it is important to ensure that the

drives are connected to a SCSI bus of a similar or higher specification. This means that you

need:

•An Ultra 160 or Ultra 320 SCSI bus. Ultra 160 SCSI supports the maximum bus speed of

160 MB per second; Ultra 320 SCSI exceeds this.

•LVD-rated SCSI cabling and terminators. The LVD interface and cable supplied with the drive

enable the data to be transferred at the drive's maximum rate and provide a maximum cable

length of 12 meters.

If you attach the drive to a lower specification SCSI bus, it may still work, but data will not be

transferred as quickly. For example, on a single-ended (SE) Ultra 2 SCSI bus the maximum

burst transfer speed of the drive is 40 MB/second and the maximum cable length is restricted

to 3 meters. See also Table 1, “supported SCSI bus types,” on page 9.

Note The drives are not compatible with high voltage differential (HVD) SCSI devices.

How can I check the SCSI bus type?

We strongly recommend that you use HP Library & Tape Tools to check your server’s current

SCSI configuration. This will provide information about the SCSI bus and the SCSI IDs in use.

dltvs160_master.fm Page 3 Monday, November 22, 2004 10:30 AM

HP Library & Tape Tools is the recommended diagnostic and support tool for your HP tape

storage product. It is available as a free download from the HP web site and is supported on

nearly all major operating systems.

See www.hp.com/support/tapetools for compatibility information, updates and the

latest version of the tool.

What are the mounting requirements for the tape drive?

Mounting bay

You need one industry standard, 5¼-inch, half-height bay in which to install the

HP StorageWorks VS160 tape drive. Maximum power requirements are 2.1 A at 5 V and

2.7 A at 12 V.

Mounting hardware

Note M3 screws are supplied with the tape drive to secure it to the mounting bay.

For many servers, no mounting tray or rails are required. Devices simply slide into the server’s

chassis and are fixed with screws. Other servers have built-in trays or rails. Rail kits for a

number of industry-standard servers may be available. For more details refer to:

www.hp.com/go/connect.

Some servers use non-standard mounting rails and do not include spares. If this is the case

with your system, you will have to order these accessories from the server manufacturer before

you can install the tape drive.

Air flow requirements

The server must provide forced cooling and be capable of drawing 3 cfm (0.08 m3/minute

or 5.1 m3/hour) of air through the tape drive at 40oC ambient operation. Always operate

the tape drive within an ambient air temperature of no more than 40oC.

It is important to keep the cooling holes in the rear and the grill in the front of the tape drive

clear of any obstructions that may hinder the air flow and to ensure that all fans in your server

are in place and operational. Make sure that empty bays have the appropriate blanking

plates installed so that airflow is maintained.

Do I need additional items for installation?

• You may need mounting hardware. See “What are the mounting requirements for the tape

drive?” above.

• If you do not have a spare, suitably rated SCSI connector on your server, a new HBA (also

known as a SCSI card) will be required. The SCSI bus rating should match or be higher than

the SCSI rating of your tape drive. See Table 1, “supported SCSI bus types,” on page 9 for

recommended HBAs. For specific details relevant to your server model please refer to

www.hp.com/go/connect. You will need to purchase and install the new HBA into an

unused, 64-bit PCI expansion slot within your server before installing your tape drive. (The

kit can also be installed in a 32-bit PCI expansion slot, but performance may be degraded.)

Refer to our World Wide Web site for recommended products, configurations and ordering

information: www.hp.com/go/connect or www.hp.com/support/dlt.

dltvs160_master.fm Page 4 Monday, November 22, 2004 10:30 AM

Backup software and drivers

Backup software

For optimum performance it is important to use a backup application that is appropriate for

your system’s configuration. In a direct attach environment, where the tape drive is attached to

a standalone server, you can use backup software that is designed for a single server

environment. In network configurations you will need backup software that supports enterprise

environments. HP, Veritas, Legato, Yosemite and Computer Associates all provide suitable

products. Further details about these and other products that may be appropriate can be

found on our connectivity web site.

1Go to our connectivity web site: www.hp.com/go/connect and select tape backup.

2Select software compatibility.

3Select your combination of operating system and tape drive model in the table. A list of

supported backup applications is displayed.

4Make sure you have a backup application that supports HP StorageWorks VS160 tape drives

and download any upgrades or patches, if required.

Drivers

Windows users

After you connect the tape drive, download the HP driver from our web site: www.hp.com/

support, see “Step 8: Verify installation” on page 23.

Refer to the accompanying README file for specific installation instructions for Windows

2000, Windows XP and Windows Server 2003 drivers.

Note: We recommend that you install drivers from the web rather than the Windows

Hardware Installation Wizard, because the HP drivers fully support the performance of your

tape drive.

dltvs160_master.fm Page 5 Monday, November 22, 2004 10:30 AM

install your

product

buy media

online

troubleshoot

with L&TT

learn about your

product

Figure 1: the

HP StorageWorks Tape

CD-ROM

dltvs160_master.fm Page 6 Monday, November 22, 2004 10:30 AM

Using the CD-ROM

The HP StorageWorks Tape CD-ROM is a central source of information about your tape drive

with utilities for getting the best performance from your tape drive.

Use the HP StorageWorks Tape CD-ROM to check installation, as described in this guide, and

to verify and troubleshoot performance after installation. It helps you to:

• Install your product, which includes access to drivers, an installation check, and

performance information and tools

• Learn about your product

• Register your product

•Buymediaonline

• Troubleshoot with HP Library & Tape Tools.

dltvs160_master.fm Page 7 Monday, November 22, 2004 10:30 AM

Figure 2: checking the SCSI connection

SCSI ribbon

cable

68-pin internal

LVD/SE connector

(Use this connector)

SCSI HBA

SCSI ribbon

cable

50-pin internal SE

connector

(Do not use)

68-pin internal

SE connector

(Do not use)

tape drive

The example shows an

Ultra 160 HBA

dltvs160_master.fm Page 8 Monday, November 22, 2004 10:30 AM

Step 1: Check the SCSI connection

Use the following questions to help you check your SCSI connection. As long as you have a

spare drive bay in your server you should have a spare connection on the internal SCSI bus.

You need to ensure it is the correct SCSI bus type. Windows users can use HP Library & Tape

Tools to check the SCSI bus type, see page 30. If you answer ‘Yes’ to all these questions, you

are ready to install your tape drive. If you answer ‘No’, you will probably need to purchase

and install additional items. For product details, go to www.hp.com/go/connect.

table 1: supported SCSI bus types

SCSI Bus Type Transfer Speed Supported

Ultra 160 LVD Up to 160 MB/s Yes. This is a recommended configuration.

Ultra 320 LVD Up to 320 MB/s Yes. This is a recommended configuration.

Ultra 2 LVD Up to 80 MB/s Yes, but this is not recommended

Ultra single-ended,

wide

Up to 40 MB/s Yes, but this is not recommended as it will restrict

performance. Do not connect to a narrow SCSI bus.

High Voltage

Differential

Up to 40 MB/s No. The drive will not work and you may damage

the drive or controller

1Is there a spare SCSI port on

the server’s internal SCSI

bus?

3Will the drive be the only

device on the bus? This is the

recommended configuration.

Do not connect to a RAID

controller channel.

2Are the SCSI ribbon cable

and HBA card rated at Ultra

160 or higher? (Make sure

the ribbon cable is

terminated. See page 19.)

Performance may be impaired.

Consider installing (if you have a spare

PCI slot) or replacing your card with an

Ultra 320 HBA. Make sure the last

device on the bus is terminated.

See table below. If the SCSI bus differs

from the recommended specification for

the drive, performance of either the

drive or the bus may be impaired.

Consider replacing your card with one

of the recommended HBAs.

Purchase and install one of the

recommended HBAs into an unused

64-bit PCI expansion slot. See table

below.

No?

Yes?

No?

4You are ready to install the

drive.

Yes

dltvs160_master.fm Page 9 Monday, November 22, 2004 10:30 AM

Figure 3: checking the SCSI ID

Example

SCSI IDs

dltvs160_master.fm Page 10 Monday, November 22, 2004 10:30 AM

Andere Handbücher für VS160 - StorageWorks DLT Tape Drive

Inhaltsverzeichnis

Andere HP Software Handbücher

HP HP Integrated Lights-Out Bedienungsanleitung

HP TR3271 Betriebsanleitung

HP C7791C - DesignJet 130 Color Inkjet Printer Konfigurationshandbuch

HP Designjet T1300 Bedienungsanleitung

HP StorageWorks 2/64 - Core Switch Bedienungsanleitung

HP BB118BV - StorageWorks Data Protector Express... Betriebsanleitung

HP 742n - Pavilion - 512 MB RAM Montage- und Bedienungsanleitung

HP C7791C - DesignJet 130 Color Inkjet Printer Konfigurationshandbuch

HP Neoview SQL Bedienungsanleitung

HP StorageWorks 1606 - Extension SAN Switch Bedienungsanleitung

HP JetCAPS Bedienungsanleitung

HP BACKCOPY Bedienungsanleitung

HP 8/20q Bedienungsanleitung

HP Configuring Arrays Bedienungsanleitung

HP e-diagtools 3.5x Bedienungsanleitung

HP ActivCard Smart Card Kurzanleitung

HP Rx2620-2 - Integrity - 0 MB RAM Bedienungsanleitung

HP BL680c - ProLiant - G5 Bedienungsanleitung

HP VL400 - Vectra - 64 MB RAM Bedienungsanleitung

HP LASERJET ENTERPRISE 500 Service-Handbuch

HP 742n - Pavilion - 512 MB RAM Kurzanleitung

HP Integrity BL860c Bedienungsanleitung

HP Kayak XU700 Bedienungsanleitung

Beliebte Software Handbücher anderer Marken

COMPRO

COMPRO COMPROFM Bedienungsanleitung

Muratec

Muratec OFFICEBRIDGE ONLINE Bedienungsanleitung

Oracle

Oracle Contact Center Anywhere 8.1 Bedienungsanleitung

Adobe

Adobe 65007312 - Photoshop Lightroom Handbuch

Avaya

Avaya NULL One-X for RIM Blackberry Bedienungsanleitung

PS Audio

PS Audio PowerPlay Betriebsanleitung

Brady

Brady LOCKOUT PRO 3.0 Service-Handbuch

Avaya

Avaya Interaction Center Bedienungsanleitung

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Handbuch

Novell

Novell GROUPWISE 8 - INTERNET AGENT Bedienungsanleitung

Oracle

Oracle Application 9i Bedienungsanleitung

Acer

Acer RDM Bedienungsanleitung

Canon

Canon Vixia HF21 Bedienungsanleitung

Canon

Canon ZR950 Bedienungsanleitung

Samsung

Samsung Auto Backup Bedienungsanleitung

Polycom

Polycom Vortex EF2201 Montage- und Bedienungsanleitung

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Bedienungsanleitung

Novell

Novell SP2 - S Bedienungsanleitung