HP Z Turbo Drive Quad Pro Bedienungsanleitung

HP Z Turbo Drive Quad Pro installation

Printed in

*838785-002*

838785-002

Linux® is the registered trademark of Linus

Torvalds in the U.S. and other countries.

Windows is a trademark of the Microsoft group

of companies.

The information contained herein is subject to

change without notice. The only warranties for

HP products and services are set forth in the

express warranty statements accompanying

such products and services. Nothing herein

should be construed as constituting an

additional warranty. HP shall not be liable for

technical or editorial errors or omissions

contained herein.

Second Edition: October 2015

First Edition: August 2015

Document Part Number: 838785-002

HP Z Turbo Drive Quad Pro installation

Introduction

This document describes how to install the HP Z Turbo Drive Quad Pro into the HP Z440, Z640, and Z840

series workstations.

Kit contents

●HP Z Turbo Drive Quad Pro

●LED cable

●Installation instructions

●Warranty information

Before you begin

To view QuickSpecs and determine the compatibility of this product with your HP computer, see

http://www.hp.com/go/productbulletin.

The minimum BIOS revision for the HP Z440, Z640, and Z840 Workstations is 1.62. If these requirements are

not met, the computer does not recognize the drive.

If you are installing an operating system image on the drive, remove all other storage devices. Install this

drive in the primary PCIe slot indicated for your workstation and install the operating system image before

installing additional HP Z Turbo Drives or HP Z Turbo Drive Quad Pros or reinstalling the other storage devices.

The preferred slots are noted in the installation instructions for each computer. If you will be using the drive

as a data drive, you do not need to remove the other storage devices.

Introduction 1

Warnings and cautions

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a

hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of

injury from a hot component, enable the surface to cool before touching.

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an

electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed area

marked with this symbol.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper

computer setup, posture, health, and work habits for computer users, and provides important electrical and

mechanical safety information. This guide is located at http://www.hp.com/ergo and on the documentation

CD (if one is included with the product).

WARNING! If a product is shipped in packaging marked with this symbol, , the product must always be

lifted by two persons to avoid personal injury due to product weight.

CAUTION: Static electricity can damage the electronic components of the computer. Before beginning these

procedures, be sure you discharge static electricity by briey touching a grounded metal object.

CAUTION: To prevent damage to the computer, observe the following Electrostatic Discharge (ESD)

precautions while performing the system parts removal and replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to

the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat, static

strap, and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP computer products. They have been extensively tested for reliability

and are manufactured to high quality standards.

Installing additional M.2 modules in the HP Z Turbo Drive Quad

Pro

You can install up to four M.2 PCIe SSD modules in this drive. Load the modules from the cover hinge to the

PCIe edge connector in the following order.

TIP: Install all M.2 modules before installing the HP Z Turbo Drive Quad Pro assembly.

2 HP Z Turbo Drive Quad Pro installation

1. Open the drive cover.

a. Slide the latch to the left of the door to the left until the red area beneath the latch is fully exposed

(1).

b. Slide the right latch to the right and hold it (2).

c. While holding the right latch, press the center of the edge of the cover and lift it (3).

2. Loosen the two captive screws on the heat sink (1).

Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 3

3. Lift the heat sink to expose the M.2 modules (2).

NOTE: The drive comes with at least two M.2 modules preinstalled.

4. Remove the stando from the next M.2 slot.

4 HP Z Turbo Drive Quad Pro installation

5. Insert stando into the curve of the right edge of the M.2 module.

6. Slide the M.2 module into the connector (1) and then press down until the stando is aligned with the

embedded nut (2).

Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 5

7. Screw the stando into the nut.

8. Reinstall the heat sink (1) and tighten the captive screws (2).

Be sure that the tabs on the heat sink are under the metal pins and can rotate.

6 HP Z Turbo Drive Quad Pro installation

9. Close the cover (1) and slide the left latch to the right until no red is showing (2).

Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 7

Accessing the internal components of the computer

1. If you need help preparing the computer for this installation, consult the removal and replacement

procedures in the HP Customer Self Repair Services Media Library at http://www.hp.com/go/sml or in the

service guide for your computer at http://www.hp.com/support/manuals.

2. Power down the workstation, and then disconnect the power cord.

3. Power down all external devices, and then disconnect them from the workstation.

4. Remove the access panel by lifting up on the release latch and raising the panel from the chassis.

Installing the drive in an HP Z440 Workstation

If more than one of any of the following drives are to be installed in a system, a unique address for each drive

must be congured before installation:

●HP Z Turbo Drive

●HP Z Turbo Drive G2

●HP Z Turbo Quad Pro

For conguration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives

on page 14.

1. Press down on the two green PCI retention clips (1) located inside the workstation until they release,

and then rotate them down to raise the retention clamp (2).

8 HP Z Turbo Drive Quad Pro installation

Andere Handbücher für Z Turbo Drive Quad Pro

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP LeftHand P4000 - SAN Solutions Bedienungsanleitung

HP StoreOnce B6000 Bedienungsanleitung

HP Smart Array P600 Bedienungsanleitung

HP C737990900 Produkthandbuch

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Bedienungsanleitung

HP P10000 Bedienungsanleitung

HP M8501 Bedienungsanleitung

HP StoreVirtual P4000 G2 Service-Handbuch

HP StorageWorks 9000 Virtual Libr Bedienungsanleitung

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Leitfaden

HP SimpleSave Bedienungsanleitung

HP P9000 Kurzanleitung zur Einrichtung

HP StoreOnce B6000 Bedienungsanleitung

HP Brio 71xx Bedienungsanleitung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP A5585A - SureStore DLT E Tape Library 4/40 Leitfaden

HP Colorado 5GB C4354A Bedienungsanleitung

HP 157770-001 - DAT Drive 20/40 Tape Bedienungsanleitung

HP Pavilion p6000 - Desktop PC Leitfaden

HP MSL4048 - StorageWorks Ultrium 920 Tape... Bedienungsanleitung

HP StorageWorks 2300 - Disk System Bedienungsanleitung

HP 9130K Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung