HQ Power VDPLB408WL Bedienungsanleitung

VDPLB408WL

FREELED 44B

4 X 8 W RGBW WIRELESS DMX-CONTROLLED

4 X 8 W RGBW-LED MET DRAADLOZE DMX-STURING

4 X LED RGBW DE 8 W À PILOTAGE DMX SANS FIL

4 X LED RGBW DE 8 W CON CONTROL DMX INALÁMBRICO

4 X 8 W RGBW-LED MIT DRAHTLOSER DMX-STEUERUNG

USER MANUAL 4

GEBRUIKERSHANDLEIDING 12

MODE D'EMPLOI 20

MANUAL DEL USUARIO 28

BEDIENUNGSANLEITUNG 36

VDPLB408WL

V. 02 –23/04/2015 2 ©Velleman nv

VDPLB408WL

V. 02 –23/04/2015 3 ©Velleman nv

VDPLB408WL

V. 02 –23/04/2015 4 ©Velleman nv

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle

could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal

waste; it should be taken to a specialized company for recycling. This device should be returned

to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing HQPower™! Please read the manual thoroughly before bringing this device into

service. If the device was damaged in transit, do not install or use it and contact your dealer.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-threatening

electroshocks.

Always disconnect mains power when device not in use or when servicing or maintenance

activities are performed. Handle the power cord by the plug only.

Indoor use only. Keep this device away from rain, moisture, splashing and dripping

liquids. Never put objects filled with liquids on top of or close to the device.

Keep this device away from children and unauthorized users.

Caution: device heats up during use.

Do not stare directly at the light source, as this may cause

epileptic seizure in sensitive people

temporarily loss of sight (flash blindness)

permanent (irreversible) eye damage.

This device falls under protection class I. It is therefore essential that the device be

earthed. Have a qualified person carry out the electric connection.

There are no user-serviceable parts inside the device. Refer to an authorized dealer for

service and/or spare parts.

Make sure that the available voltage does not exceed the voltage stated in the specifications of this

manual.

Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if

necessary.

Use an appropriate safety cable to fix the device (e.g. VDLSC7N or VDLSC8N).

Install the device at a minimal distance of 0.5 m from flammable and explosive objects or

substances.

Respect a minimum distance of 0.5 m between the device’s light output and any illuminated surface.

The maximum ambient temperature is 40 °C. Do not operate the device at higher temperatures.

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Keep this device away from dust and extreme temperatures. Make sure the ventilation

openings are clear at all times. For sufficient air circulation, leave at least 1" (± 2.5 cm)

in front of the openings.

VDPLB408WL

V. 02 –23/04/2015 5 ©Velleman nv

Protect this device from shocks and abuse. Avoid brute force when operating the device.

Familiarise yourself with the functions of the device before actually using it. Do not allow operation

by unqualified people. Any damage that may occur will most probably be due to unprofessional use

of the device.

All modifications of the device are forbidden for safety reasons. Damage caused by user modifications

to the device is not covered by the warranty.

Only use the device for its intended purpose. All other uses may lead to short circuits, burns,

electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the

warranty.

Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and

the dealer will not accept responsibility for any ensuing defects or problems.

Mechanical wear and LEDs are not covered by warranty.

A qualified technician shall install and service this device.

Do not switch the device on immediately after it has been exposed to changes in temperature.

Protect the device against damage by leaving it switched off until it has reached room temperature.

This device is designed for professional use on stage, in discos, theatres, etc. The device shall only

be used indoors with an alternating current of 100-240 VAC, 50/60 Hz.

Lighting effects are not designed for permanent operation: regular operation breaks will prolong their

lives.

Use the original packaging if the device is to be transported.

Keep this manual for future reference.

4. Features

The FREELED 44B is a small, lithium-ion battery-powered uplighter that creates stunning colour cross-

fades controlled by DMX. With its 8 W RGBW LED, it is perfect for uplighting or creating light columns in

banquet rooms for weddings or corporate events. The angle is easy to adjust using the included bracket.

produces flicker-free light which makes it ideal for use with a camera

the rechargeable lithium battery lasts up to 20 hours from a single charge

master/slave mode for synchronized operation of multiple units linked in a chain

DMX-controlled via 4, 6 or 10 channels

o4-channel mode: RGBW

o6-channel mode: dimmer, RGBW, shutter

o10-channel mode: dimmer, RGBW, colour, shutter, auto programme, programme speed,

dimmer mode

with IR remote control

optional protection bag with 4 rain covers: VDPLB408WLB

5. Overview

Refer to the illustrations on page 2 of this manual.

microphone

DMX input

display

on-off switch

control panel

power input with fuse

AUTO button

DMX output

foot

power output

VDPLB408WL

V. 02 –23/04/2015 6 ©Velleman nv

6. Remote Control

Refer to the illustrations on page 2 of this manual.

key

step 1

step 2

step 3

description

blackout

any key

auto

+/-

Auto programme mode

speed

+/-

strobe

+/-

sound

sensitivity

+/-

Sound mode

strobe

+/-

strobe

+/-

Dimmer

speed

+/-

Auto programme speed

sensitivity

+/-

Sensitivity for sound mode

+/-

manual

Manual RGBW mode

RGBW

+/-

Value setting

strobe

+/-

Strobe speed

+/-

fade

+/-

Fading mode

speed

+/-

strobe

+/-

RGBW

+/-

Manual colour selection

strobe

+/-

function

+/-

0-9

strobe

+/-

7. Installation

Choose a suitable mounting spot. Connect the power cord to the mains and switch on [7]. Switch off and

disconnect after use.

Mounting the Device

Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable

norms.

The carrying construction must be able to support 10 times the weight of the device for 1 hour

without deforming.

The installation must always be secured with a secondary attachment e.g. a safety cable.

Never stand directly below the device when it is being mounted, removed or serviced. Have a

qualified technician check the device once a year and once before you bring it into service.

Install the device in a location with few passers-by that is inaccessible to unauthorised persons.

Overhead mounting requires extensive experience: calculating workload limits, determining the

installation material to be used… Have the material and the device itself checked regularly. Do not

attempt to install the device yourself if you lack these qualifications as improper installation may

result in injuries.

For truss mounting, use appropriate clamps and brackets.

Make sure there is no flammable material within a 0.5 m radius of the device.

Have a qualified electrician carry out the electric connection.

Connect the device to the mains with the power plug. All devices must be powered directly off a

grounded switched circuit and cannot be run off a rheostat or dimmer circuit, even if the rheostat or

VDPLB408WL

V. 02 –23/04/2015 7 ©Velleman nv

dimmer channel is used solely for 0 % to 100 % switching.

The device has a power output [10]to supply power to another device. When connecting several

devices in a daisy chain via this output, make sure that the total current does not exceed the power

line’s nominal current. Use power cables with an adequate section.

The installation has to be approved by an expert before the device is taken into service.

DMX-512 Connection

When applicable, connect an XLR cable to the female XLR output of a controller (not incl.) and the

other side to the male XLR input [6] of the device. Multiple devices can be linked through serial

linking. The linking cable shall be a dual core, screened cable with XLR input and output connectors.

Maximum recommended serial data link distance is 500 meters (1640 ft). Maximum recommended

number of devices on a serial data link is 32 devices.

A DMX terminator is recommended for installations where the DMX cable has to run a long distance

or is in an electrically noisy environment (e.g. discos). The terminator prevents corruption of the

digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω

resistor between pins 2 and 3, which is then plugged into the XLR output socket [10]of the last

device in the chain.

8. Operation

The device can be used in the following modes:

stand-alone mode: automatic or sound-activated

master/slave

with a DMX-512 controller.

8.1 Control Panel

Control Buttons

Access the control panel functions using the four panel buttons [3] located below the display [2].

Button

Function

to access the menu, quit the current function without saving the setting, or quit the

to scroll upward in a list of functions or options, or increase a value

DOWN

to scroll downward in a list of functions or options, or decrease a value

ENTER

to confirm and save a selected option or value

8.2 Menu

menu level 1

menu level 2

menu level 3

description

4-CH

d 1

Channel selection

d512

6-CH

d 1

d512

10CH

d 1

d512

C--

C 1

1: R

2: G

3: B

4: W

5: GB

6: RB

7: RG

8: RGB

9: RW

10: GW

11: BW

VDPLB408WL

V. 02 –23/04/2015 8 ©Velleman nv

12: RGW

13: RBW

14: GBW

15: RGBW

P--

P 1

Programme selection

P 2

P 3

P 4

S--

S 1

Programme speed

S100

Snd

Sound-activated mode

SenS

u 0

Sound sensitivity

u100

U--

r 0

User-programmed colours

255

g 0

255

b 0

255

W 0

255

dIM

OFF

Dimmer speed setting

dIM1

dIM2

dIM3

SET

OFF

S-tr

drAS

drAU

Automatic wireless reception

drCH

dr 1

Manual wireless reception

dtAS

dtAU

Automatic wireless transmission

dtCH

dr 1

Manual wireless transmission

8.3 Stand-Alone Mode

In stand-alone mode, the device runs one of the built-in programs: automatic or sound-activated.

Stand-Alone Mode with Built-in Programme

To set the device to stand-alone mode:

1. Unplug any connection from the DMX input [6] of the device.

2. Press MENU to open the menu.

3. Select <P-->.

4. Select one of the built-in programmes.

Sound Activation

With sound activation, the built-in program responds to sound. To use sound activation with the selected

built-in program:

1. Press MENU to open the menu.

2. Select <Snd>.

VDPLB408WL

V. 02 –23/04/2015 9 ©Velleman nv

8.4 Master/Slave Mode

The master/slave mode allows for connecting several devices to a single master device in a daisy chain.

All slave devices will then work synchronously with the master device. The first device in the daisy chain

functions as the master device.

To set the devices to master/slave mode:

1. Unplug any connection from the DMX input [6] of the master device (the first device in the chain).

2. Connect the DMX input of the first slave device to the DMX output [9] of the master device.

3. Connect the DMX input of the subsequent slave devices to the DMX output of the previous slave

device.

4. On the master device, press MENU to open the menu.

5. Select <4-CH>, <6-CH> or <10CH> to select one of the channel modes.

6. The slave devices will automatically follow the master device upon connection.

8.5 DMX Mode

This mode allows you to control the device by any universal DMX controller.

All DMX-controlled devices need a digital start address so that the correct device responds to the

signals. This digital start address is the channel number from which the device starts to “listen” to

the DMX controller. The same starting address can be used for a whole group of devices or an

individual address can be set for every device.

When all devices have the same address, all the units will “listen” to the control signal on one

particular channel. In other words: changing the settings of one channel will affect all devices

simultaneously. If you set individual addresses, each device will “listen” to a separate channel

number. Changing the settings of one channel will only affect the device in question.

DMX Starting Address

first device

second device

third device

…

4 channels

5 (1 + 4)

9 (5 + 4)

…

6 channels

7 (1 + 6)

13 (7 + 6)

…

To set the device to work with a DMX controller

1. Press MENU to open the menu.

2. Select <4-CH>, <6-CH> or <10CH>.

3. Set the DMX starting address.

DMX Channel Values

4-channel mode:

channel

function

from

description

red

000

255

from 0 to 100 %

green

000

255

from 0 to 100 %

blue

000

255

from 0 to 100 %

white

000

255

from 0 to 100 %

6-channel mode:

channel

function

from

description

dimmer

000

255

from 0 to 100 %

red

000

255

from 0 to 100 %

green

000

255

from 0 to 100 %

blue

000

255

from 0 to 100 %

white

000

255

from 0 to 100 %

strobe

000

010

no function

011

255

from slow to fast

VDPLB408WL

V. 02 –23/04/2015 10 ©Velleman nv

10-channel mode:

channel

function

from

description

dimmer

000

255

from 0 to 100 %

red

000

255

from 0 to 100 %

green

000

255

from 0 to 100 %

blue

000

255

from 0 to 100 %

white

000

255

from 0 to 100 %

manual colour

colour

temperature

000

010

no function

011

030

R 100 %, G 0-100 %, B 0 %

031

050

R 100-0 %, G 100 %, B 0 %

051

070

R 0 %, G 100 %, B 0-100 %

071

090

R 0 %, G 100-0 %, B 100 %

091

110

R 0-100 %, G 0 %, B 100 %

111

130

R 100 %, G 0 %, B 100-0 %

131

150

R 100 %, G 0-100 %, B 0-100 %

151

170

R 100-0 %, G 100-0 %, B 100 %

171

200

R 100 %, G 100 %, B 100 %, W 100 %

201

205

colour temperature 1

206

210

colour temperature 2

211

215

colour temperature 3

216

220

colour temperature 4

221

225

colour temperature 5

226

230

colour temperature 6

231

235

colour temperature 7

236

240

colour temperature 8

241

245

colour temperature 9

246

250

colour temperature 10

251

255

colour temperature 11

strobe

000

010

no function

011

255

from slow to fast

auto/sound

programmes

000

010

no function

011

060

auto programme 1

061

120

auto programme 2

121

180

auto programme 3

181

240

auto programme 4

241

255

sound show

auto speed

000

255

from slow to fast

dimmer mode

000

051

preset dimmer speed from display menu

052

101

dimmer speed mode off

102

152

dimmer speed mode 1 (fast)

153

203

dimmer speed mode 2 (middle)

204

255

dimmer speed mode 3 (slow)

9. Cleaning and Maintenance

All screws shall be tightened and free of corrosion.

The housing, the lenses, the mounting supports and the installation location (e.g. ceiling, suspension,

trussing) shall not be deformed, modified or tampered with; e.g. do not drill extra holes in mounting

supports, do not change the location of the connections…

Mechanically moving parts must not show any signs of wear and tear.

The electric power supply cables must not show any damage. Have a qualified technician maintain

the device.

Disconnect the device from the mains prior to maintenance activities. Let the device cool down.

Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

Inhaltsverzeichnis

Sprachen:

Andere HQ Power Scheinwerfer Handbücher

HQ Power

HQ Power VDPL300M Bedienungsanleitung

HQ Power

HQ Power VDLL6RL Bedienungsanleitung

HQ Power

HQ Power vdpl300DD Bedienungsanleitung

HQ Power

HQ Power VDPLP1803RGB Bedienungsanleitung

HQ Power

HQ Power VDPL310FC2 Bedienungsanleitung

HQ Power

HQ Power VDPL300MF4 Bedienungsanleitung

HQ Power

HQ Power VDPLPS36BP Bedienungsanleitung

HQ Power

HQ Power VDP575MHS20FL Bedienungsanleitung

HQ Power

HQ Power VDPLW1252 Bedienungsanleitung

HQ Power

HQ Power HQLE10017 Bedienungsanleitung

HQ Power

HQ Power VDPL304LF Bedienungsanleitung

HQ Power

HQ Power VDPL310FC Bedienungsanleitung

HQ Power

HQ Power VDPL303BS Bedienungsanleitung

HQ Power

HQ Power VDP150CC6 Bedienungsanleitung

HQ Power

HQ Power VDL15UV Bedienungsanleitung

HQ Power

HQ Power VDPLB3D Bedienungsanleitung

HQ Power

HQ Power VDLPROM1 Bedienungsanleitung

HQ Power

HQ Power VDPL300D Bedienungsanleitung

HQ Power

HQ Power XMPL8 Bedienungsanleitung

HQ Power

HQ Power VDPL300CB Bedienungsanleitung

HQ Power

HQ Power VDPL300MR ARUZO Bedienungsanleitung

HQ Power

HQ Power VDPL300CB Bedienungsanleitung

HQ Power

HQ Power HQLB10001 Bedienungsanleitung

HQ Power

HQ Power VDLLUF Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung