Huawei UPS5000-E-200K-SM Bedienungsanleitung

Issue: 08

Part Number: 31507655

Date: 2019-10-16

UPS5000-E-(50 kVA-200 kVA)

Quick Guide (50 kVA Power Modules)

1Overview

UPS Model Capacity Weight Dimensions (H x W x D)

UPS5000-E-200K-SM 50 kVA, 100 kVA,

150 kVA, 200 kVA

330 kg 2000 mm x 600 mm x 850 mm

UPS5000-E-200K-FM 390 kg

UPS5000-E-200K-SM UPS5000-E-200K-FM

(1) Power distribution

subrack cover (2) Bypass input switch

(3) Maintenance

bypass switch (4) Main input switch

(5) Output switch (6) CM

(7) Bypass module (8) Power modules

(9) MDU (10) Filler panels

(1) Power modules (2) Bypass module

(3) Control module

(CM) (4) Power distribution

subrack cover

(5) Filler panels (6) Monitor display unit

(MDU)

(7) Maintenance

bypass switch

2Installing the UPS

2. Use a hammer drill to drill four holes for installing

expansion bolts and then install four expansion

bolts in the holes. Remove the bolt, spring washer,

and flat washer.

3. Slide the cabinet on its castors to the installation

position.

4. (Optional) If the castors of the UPS need to be

lifted from the ground, perform Step 1 to Step 2 in

Non-Secured Installation.

5. Remove the rear panel of the cabinet, and then

open the front door.

Secured Installation

1. Determine the position for installing the cabinet. Mark mounting holes based on the drawings.

(unit: mm)

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools during installation and operation.

3. Only Huawei engineers or engineers certified by Huawei are allowed to install, commission, and

maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the

resulting UPS faults are beyond the warranty scope of Huawei.

4. This document describes how to install a single UPS. For details about how to install parallel

systems, contact Huawei technical support.

2. Check whether the bottom of the cabinet is horizontal by using a level. If the cabinet is not

leveled, adjust the leveling feet.

1. Lower the four leveling feet at the bottom of the cabinet by using a wrench until all the four

castors at the bottom hang in the air and the leveling feet bear the whole cabinet weight.

7. Insert four M12x115 expansion bolts into

the expansion bolt holes in the floor, and

tighten the expansion bolts.

6. Remove the four rubber plugs from the

bottom of the cabinet (two on the front and

two at the back).

Non-Secured Installation

3Connecting Cables

1. This document describes cable routing by removing the top cover when there are two mains

inputs.

2. In the case of single mains, you do not need to connect bypass input power cables and remove

short-circuit copper bars.

UPS Cable Connection Reference

3.1

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets and

surrounding environment clean and tidy.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

The cabling route is for reference only. Connect cables based on site requirements.

NOTE

2. Remove the cover from the power

distribution subrack.

3. Remove the copper bars between mains

input terminals and bypass input terminals.

(If the mains input and bypass input share

a power source, skip this step.)

The cover can be opened only if the

maintenance bypass switch is OFF.

4. Connect the ground cable to the UPS.

In the preceding figure, circled wiring

terminals are primary ones and must

connect to the ground cable.

1. Remove the small covers of the cabinet top.

Connecting Cables

3.2

Connecting Cables to the UPS5000-E-200K-SM

Scenario 1: Routing Cables from the Top

6. Connect the output power cable.

5. Connect the mains input cables to mains input

power distribution terminals 1L1, 1L2, and 1L3,

respectively.

Connect the bypass input cables to bypass

input power distribution terminals 2L1, 2L2, and

2L3, respectively.

Connect the N wires of the mains and bypass

input cables to the input power distribution

terminal N.

Route a neutral wire from the middle of

the positive and negative battery strings.

Take a battery string consisting of 40

batteries as an example. A neutral wire

is routed from the middle of positive and

negative battery strings, each consisting

of 20 batteries.

NOTE

7. Connect the battery cable.

8. Connect signal cables.

NOTE

The number and

color of signal

cables in the figure

are for reference

only. Signal cables

can be routed along

the left or right side

of the cabinet.

Route signal cables

based on the actual

situation.

NOTE

For the cable

connection method

for the TN-C system,

see the user manual.

Scenario 2: Routing Cables from the Bottom

1. Remove the cover from the power

distribution subrack.

2. Remove the copper bars between mains

input terminals and bypass input terminals.

3. Remove small covers from the bottom

based on site requirements.

4. Connect power cables.

For the screw specifications and torque used

for connecting cables in a bottom cable

routing scenario, refer to the top cable

routing scenario. This section only shows the

cable routes in the bottom cable routing

scenario.

NOTE

5. Connect signal cables.

The number and color of signal cables in

the figure are for reference only. Signal

cables can be routed along the left or

right side of the cabinet. Route signal

cables based on the actual situation.

NOTE

Connecting Cables to the UPS5000-E-200K-FM

2. Remove the cover from the power

distribution subrack.

Scenario 1: Routing Cables from the Top

1. Remove a certain number of small covers

from the top of the cabinet based on site

conditions.

4. Connect the ground cable to the UPS.3. Remove the copper bars between mains

input terminals and bypass input terminals.

5. Connect the mains input power cable. 6. Connect the bypass input power cable.

Route a neutral wire from the middle of the

positive and negative battery strings.

Take a battery string consisting of 40 batteries as

an example. A neutral wire is routed from the

middle of positive and negative battery strings,

each consisting of 20 batteries.

NOTE

7. Connect the battery cable.

8. Connect the output power cable. 9. Connect signal cables.

Scenario 2: Routing Cables from the Bottom

A cable entry cabinet needs to be installed when cables are routed from the bottom. This

document uses the cable entry cabinet installed on the right of the UPS cabinet as an example.

1. (Optional) Determine the installation

position for the cable entry cabinet, and

draw mounting holes in the installation

position based on drawings.

2. Remove the right and rear covers from the

UPS cabinet, and remove the front and rear

covers from the cable entry cabinet. Put away

the removed screws and covers.

3. Adjust the anchor bolts of the cable entry

cabinet to make it flush with the UPS cabinet.

4. Install equipotential plate mounting kits on the

same horizontal plane of the UPS cabinet and

cable entry cabinet.

Andere Handbücher für UPS5000-E-200K-SM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei UPS Handbücher

Huawei

Huawei UPS5000-A-200K-ST Bedienungsanleitung

Huawei

Huawei UPS5000-E-40 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-S-880K-SM Bedienungsanleitung

Huawei

Huawei UPS2000-G-2KRTL Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei FusionPower6000 Betriebsanleitung

Huawei

Huawei UPS2000-A-6KTTS-S Bedienungsanleitung

Huawei

Huawei UPSJZ-T Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-30KTTL Bedienungsanleitung

Huawei

Huawei UPS5000-H Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-30 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-S-600 Bedienungsanleitung

Huawei

Huawei UPS5000-A-400K-SL Bedienungsanleitung

Huawei

Huawei UPS2000-G-6KRTLL Bedienungsanleitung

Huawei

Huawei UPS5000-S200K-SM Bedienungsanleitung

Huawei

Huawei SUN2000-250KTL Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-30 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-E-BF Series Bedienungsanleitung

Huawei

Huawei PowerCube 500 Bedienungsanleitung

Huawei

Huawei UPS5000-E-400K-FMS Bedienungsanleitung

Huawei

Huawei SmartLi 2.0 Bedienungsanleitung

Huawei

Huawei SmartLi 2.0 Bedienungsanleitung

Huawei

Huawei PDC-0038V4ACIOA-V2 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung