Huawei UPS5000-S-600 Bedienungsanleitung
1
Issue: 04
Part Number: 31509969
Date: 2019-06-20
UPS5000-S-600 kVA
Quick Guide (Three-phase, Three-wire)
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
1Overview
UPS Model Weight Dimensions (H x W x D)
UPS5000-S-600K-NN 950 kg 2000 mm x 1400 mm x 850 mm
(1) Power modules
(2) Control module
(3) Mains surge protection box
(4) Bypass surge protection box
(5) Fan power module
(6) Bypass module
2
1. Before installation, read the user manual carefully to get familiar with product information and
safety precautions.
2. Use insulated tools during installation.
3. Only engineers certified by Huawei or its agents are allowed to install, commission, and
maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the UPS
faults caused are beyond the warranty scope of Huawei.
2Installing the UPS
The UPS can be installed on channel steel or the floor. Install the UPS based on site requirements.
Floor installation: Determine the UPS mounting holes using the marking-off template, drill holes,
and install the expansion sleeves of the M12x60 expansion bolts in the mounting holes.
Channel steel installation: Ensure that the distance between the outer surfaces of two pieces of
channel steel is 800 mm and secure the channel steel to the floor using expansion bolts.
Huawei does not provide channel steel or expansion bolts used for securing channel steel. The
customer should purchase channel steel (recommended width: 50 mm or more) and expansion
bolts.
Determining the UPS Installation Position
2.1
A: mounting holes on the channel steel
B: mounting holes on the floor
Unit: mm
3
•Floor mounting: Use eight M12x60 expansion bolts to secure the cabinet to the ground.
•Channel steel mounting: Use eight M12x60 common bolts to secure the cabinet to channel
steels.
Securing the UPS
2.2
(1)
Cabinet mounting holes (ground installation mode)
(2)
Cabinet mounting holes (channel steel installation mode)
Installing the Front, Rear, Left, and Right Anchor Baffle Plates
2.3
3Connecting Cables
1. This document uses dual mains as an example.
2. Single mains does not need bypass input power cables connected or connecting copper bars
removed.
3. During cable installation, reserve the removed screws, front power distribution covers, and rear
cover. Reinstall them after connecting cables.
NOTE
4
UPS Cable Connection Reference
3.1
•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may
ignite and cause personal injury or device damage.
•After cables have been installed, clean the cabinet in a timely manner. Ensure that there is no
foreign matter inside and around the cabinet.
Installing Cables
3.2
2. Remove the cover from the top of the bypass
cabinet based on the cable route and cable
dimensions.
1. Open the front door of the bypass cabinet,
and remove front power distribution covers.
(1) Cover for power cables
(2) Signal cable hole
2
1
5
3. Remove the rear cover from the bypass cabinet,
and then remove the connecting copper bars
between the mains input terminals and bypass
input terminals. (If the mains input and bypass
input share a power source, skip this step.)
4. Connect the ground cable to the UPS.
6. Connect the output power cables.5. Connect the mains input power cables.
6
7. Connect bypass input power cables. 8. Connect the battery cables.
9. Connect signal cables.
The figure shows the signal cable routing and is for reference only. Connect the cable based on
the actual situation.
NOTE
7
4Installation Verification
1. Check that there is no foreign matter at the top and bottom of the cabinet, copper bars, and the
rear of modules.
2. (Remove the paper protective film from the
sealing putty.) After routing cables and
verifying cable connections, seal the gap
between cables and the cabinet using sealing
putty.
Dustproof cover
3. After verifying the installation, reinstall all
the covers. After the installation is complete,
reinstall the dustproof cover to prevent dust
inside if the UPS is not to be powered on
immediately.
Bottom
Copper bars
Top
Sealing putty
Sealing putty must be used as a whole and the
gap can be sealed only from the top.
Paper
protective film
8
5Powering On and Starting the UPS
1. Before powering on the UPS, ensure that all the items in the UPS5000 Commissioning and
Acceptance Report and Chapter 4 have been checked.
2. Measure the voltage and frequency where the external input switch is located. 380 V AC/400 V
AC/415 V AC/420 V AC voltage system: 138–485 V AC (line voltage), 480 V AC voltage system:
192–528 V AC (line voltage), and the frequency range is 40–70 Hz.
3. Before you power on the UPS, check that all external switches are OFF.
Powering On the UPS
5.1
Close the external bypass and mains input switches.
After the UPS is powered on, it starts initialization. The LCD
displays the Huawei logo and an initialization progress bar.
Initial Startup
5.2
Download and install the Service Expert app.
After login, tap Power-on password activation
on the screen. A message is displayed,
indicating whether to start the UPS. Tap OK.
Insert the WiFi module into the USB port on the
MDU. Enable the mobile phone WLAN, search
for the UPS_WIFI signal, and connect to the
WiFi signal. The password is Changeme.
Set the Site and Device Type as required, and
connect the device. Set IP to 192.168.0.10, Port
to 443, Username to admin, Password to
Changeme, and click Login.
Enter Bar code and Verification code
obtained from the LCD on the Offline
Activation screen. Tap Generate PWD to
generate a startup password.
Set Site and Device Type as required,
and tap Offline Activation.
Enter the generated password in the
password textbox on the LCD to start the
UPS.
Use the app to
start the UPS
online?
Yes
No, start the
UPS offline
On the app home screen, tap StartUp to access the Set Startup screen.
•If the UPS is powered on for the first time, you need to obtain the startup password from the
Service Expert app. Skip this step if the UPS is not powered on for the first time.
•The Service Expert app can be downloaded from Google Play Store and can run on Android.
1. Obtain the startup password.
9
2. Set the language, time, date, network parameters, and system parameters on the Settings
Wizard screen.
3. After you perform the settings, the Bypass mode and No battery alarms are reported by the
MDU and do not need to be cleared. If there is any other alarm, you need to rectify the fault.
4. View the system running status diagram on the MDU to check that the UPS is working in bypass
mode.
1. Set system parameters with caution because normal UPS operation depends on correct settings.
Set Single/Parallel with caution. Incorrect setting may affect the normal UPS operation.
Output Voltage level refers to the line voltage level. Set it based on site requirements.
Set Output frequency correctly. Otherwise, the UPS may not work properly and loads may be
affected.
2. Battery parameter settings have great impact on battery maintenance, battery lifespan, and
discharge time.
10
System User LCD Preset Password WebUI Preset Password
admin (system administrator) 000001 Changeme
operator (common user) 000001 Changeme
To ensure system security,
change the LCD and WebUI
passwords after the first login.
NOTE
1. On the main menu, choose Common Functions and tap
Inv. ON.
2. In the displayed login window, enter the user name and
password, and tap .
3. In the displayed dialog box, tap Yes to start the inverter.
1. After the inverter starts, the UPS works in normal mode. The Bypass mode alarm disappears.
Check that the UPS has transferred to normal mode by viewing the system running status
diagram. Check that the UPS three-phase output voltage and frequency are normal by viewing
AC Output on the MDU. Use a multimeter to check that the valid three-phase output voltage
and frequency are normal.
2. After confirming that the battery strings are properly connected, close the battery string input
circuit breaker. If there are multiple battery strings, close the circuit breaker for each battery
string and then the general circuit breaker between battery strings and the UPS. The No battery
alarm disappears from the MDU.
3. Close the external output switches to supply power to loads.
Powering On Loads
5.4
(Optional) Setting Parameters for the BCB Box
5.5
(Optional) If a BCB box is configured, choose Settings > Dry Contact Set, set MUE05A
connection to Enable, and then set BCB connection [OL] and Battery breaker [STA] to Enable.
Starting inverter
5.3
Andere Handbücher für UPS5000-S-600
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Huawei UPS Handbücher
Huawei
Huawei UPS5000-S-1600KVA-FP Bedienungsanleitung
Huawei
Huawei UPS5000-E-600K-SC Bedienungsanleitung
Huawei
Huawei iBAT 2.0-CIM01C2 Bedienungsanleitung
Huawei
Huawei UPS2000-G-6 kVA Bedienungsanleitung
Huawei
Huawei UPS2000-G-2KRTL Bedienungsanleitung
Huawei
Huawei UPS2000-A-6KTTS-S Bedienungsanleitung
Huawei
Huawei FusionPower6000 Betriebsanleitung
Huawei
Huawei UPS2000-H Bedienungsanleitung
Huawei
Huawei UPS5000-H-600 kVA Bedienungsanleitung
Huawei
Huawei UPS2000-G Series Bedienungsanleitung
Huawei
Huawei UPS5000-S-600 Bedienungsanleitung
Huawei
Huawei UPS5000-A-400K-SL Bedienungsanleitung
Huawei
Huawei UPS2000-G-3KRTLL Bedienungsanleitung
Huawei
Huawei UPS2000-G1-6 kVA Bedienungsanleitung
Huawei
Huawei PDU8000-0630ACV4-SCA108 Bedienungsanleitung
Huawei
Huawei UPS5000-A-H Series Bedienungsanleitung
Huawei
Huawei UPS5000-E Series Bedienungsanleitung
Huawei
Huawei UPS5000-E Series Bedienungsanleitung
Huawei
Huawei UPS5000-E Series Bedienungsanleitung
Huawei
Huawei UPS5000-S-400K-SM Bedienungsanleitung
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
