Hubbell GAI-Tronics HUBBCOM GSC1100 Bedienungsanleitung

Pub. 42004-532E 
 
G A I - T R O N I C S ®
A H U B B E L L C O M P A N Y 
HUBBCOM™ GSC1100/GSC2100  
Dual-Port DT/WM Smart Controllers 
TA B L E O F CO N T E N T S 
GAI-Tronics 3030 Kutztown Road Reading, PA 19605 USA 
610-777-1374 ◼800-492-1212 ◼Fax: 610-796-5954 
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS 
Confidentiality Notice.....................................................................................................................1 
General Information.......................................................................................................................1 
Important Safety Instructions.........................................................................................................1 
Installation ......................................................................................................................................3 
Desktop Units ..........................................................................................................................................3 
Wall Mounting ........................................................................................................................................4 
Single or double gang electrical box mounting: ...................................................................................4 
Surface mounting with toggle bolts or wall anchors:............................................................................5 
Wiring......................................................................................................................................................6 
Handset .................................................................................................................................................6 
RTU Input/Output................................................................................................................................. 6 
RS-485 and External Speaker Connections ..........................................................................................6 
Ethernet.................................................................................................................................................7 
24 V DC Power.....................................................................................................................................7 
Antenna.................................................................................................................................................7 
Activation.........................................................................................................................................8 
Activation with DHCP............................................................................................................................8 
Activation without DHCP ......................................................................................................................9 
Service and Spare Parts................................................................................................................10 
Reference Documents...................................................................................................................10 
Specifications ................................................................................................................................10 
Approvals.......................................................................................................................................10 

Pub. 42004-532E

G A I - T R O N I C S ®

A H U B B E L L C O M P A N Y

HUBBCOM™ GSC1100/GSC2100

Dual-Port DT/WM Smart Controllers

GAI-Tronics 3030 Kutztown Road Reading, PA 19605 USA

610-777-1374 ◼800-492-1212 ◼Fax: 610-796-5954

VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

Confidentiality Notice

This manual is provided solely as an installation, operation, and maintenance guide and contains sensitive

business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics

retains all intellectual property and other rights in or to the information contained herein, and such

information may only be used in connection with the operation of your GAI-Tronics product or system.

This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third

party.

General Information

This manual covers the installation of HUBBCOM Dual-Port Desktop/Wall-Mount Smart Controllers,

Models GSC1100 and GSC2100. The Model GSC1100 Smart Controller includes a handset and is only

suitable for horizontal (landscape) installation. The Model GSC2100 Smart Controller does not include a

handset and is suitable for vertical (portrait) or horizontal (landscape) use (see Figure 1). See the GAI-

Tronics website at https://www.gai-tronics.com for system applications, system specifications, warranty

information, and the GUDA (GAI-Tronics Universal Device Application).

HUBBCOM smart controllers require activation and configuration when placed into service (see the

Activation section). Use the GUDA (GAI-Tronics Universal Device Application) software to configure

the smart controller for its intended purpose. Pub. 42004-531 provides instructions to obtain, install, and

run the GUDA software. Refer to Pub. 42004-551 for information on HUBBCOM smart controller

configuration parameters (see the Reference Documents section).

Important Safety Instructions

•Read, follow, and retain instructions—All safety and operating instructions should be read and

followed before operating the unit. Retain instructions for future reference.

•Heed warnings—Adhere to all warnings on the unit and in the operating instructions.

•Attachments—Attachments not recommended by the product manufacturer should not be used, as

they may cause hazards.

•Servicing—Do not attempt to service this unit by yourself. Opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

•HUBBCOM Smart Controllers are for indoor use only.

ATTENTION

—Install equipment without modification and according to all applicable local,

national, and international electrical codes. North America—Consult the

National Electrical Code (NFPA 70), Canadian Standards Association (CSA

22.1), and local codes for specific requirements regarding your installation.

Install Class 2 circuit wiring must in accordance with the NEC.

Pub. 42004-532E

HUBBCOM™GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 2 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

Only trained, qualified, and competent personnel must install these enclosures. Installation must comply

with state and national regulations, as well as safety practices for this type of equipment.

WARNING

—Use only 24 V dc power supplies that conform to UL/CSA/CE Class II, Double

Insulated supplies with over voltage and short circuit protection. Use only a dc

source with a 50-watt maximum output or fuse the supply with a 2-amp fuse.

EMI standards to Class B.

•Onderhoud—Probeer dit apparaat niet zelf te repareren. Het openen of verwijderen van afdekkingen

kan u blootstellen aan gevaarlijke spanning of andere gevaren. Laat alle onderhoud over aan bevoegd

onderhoudspersoneel.

•HUBBCOM Smart Controllers zijn alleen bedoeld voor gebruik binnenshuis.

AANDACHT

—Gebruik alleen 24 VDC-voedingen die voldoen aan UL/CSA/CE Klasse II,

dubbel geïsoleerde voedingen met overspanning en kortsluitbeveiliging.

Gebruik alleen een DC-bron met een maximale output van 50 W of fuseer de

voeding met een 2-ampère zekering. EMI-normen voor klasse B.

•Dépannage—N'essayez pas de réparer cet appareil vous-même. Ouvrir ou retirer les capots peut

vous exposer à des tensions dangereuses ou à d'autres dangers. Confiez toute réparation à un

personnel qualifié.

•Les contrôleurs intelligents HUBBCOM sont conçus pour une utilisation en intérieur uniquement.

ATTENTION

—Utilisez uniquement des alimentations 24 Vcc conformes à UL/CSA/CE Classe

II, des alimentations à double isolation avec protection contre les surtensions et

les courts-circuits. Utilisez uniquement une source cc avec une sortie maximale

de 50 watts ou fusionnez l’alimentation avec un fusible de 2 ampères. Normes

EMI à la classe B.

•Manutenzione—non tentare di riparare l'unità da soli. L'apertura o la rimozione dei coperchi

potrebbero esporre a tensioni pericolose o altri rischi. Rivolgersi a personale qualificato per

l'assistenza.

•Gli HUBBCOM Smart Controller sono progettati esclusivamente per uso interno.

AVVERTIMENTO

—Utilizzare solo alimentatori a 24 V cc conformi a UL/CSA/CE Classe II,

alimentatori a doppio isolamento con protezione da sovratensione e

cortocircuito. Utilizzare solo una fonte di corrente continua con un'uscita

massima di 50 watt o collegare l'alimentazione con un fusibile da 2 A.

Standard EMI per la classe B.

•Mantenimiento—no intente reparar esta unidad por sí mismo. Abrir o quitar las cubiertas puede

exponerlo a un voltaje peligroso u otros peligros. Remita todo el servicio a personal de servicio

calificado.

•Los controladores inteligentes HUBBCOM están diseñados para uso en interiores solamente.

ADVERTENCIA

—Utilice solo fuentes de alimentación de 24 V cc que cumplan con

UL/CSA/CE Clase II, fuentes con doble aislamiento con sobretensión y

protección contra cortocircuitos. Utilice solo una fuente de CC con una

salida máxima de 50 vatios o fusione la fuente con un fusible de 2 amperios.

Estándares EMI a Clase B.

Pub. 42004-532E

HUBBCOM™ GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 3 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

Installation

Mount the HUBBCOM Model GSC1100 or Model GSC2100 to a wall or use them as desktop units.

NOTE: HUBBCOM devices require access to an SNTP (simple network time protocol) server.

Figure 1. HUBBCOM Model GSC1100 (horizontal) and Model GSC2100 (vertical) Smart Controllers

Desktop Units

Use the HUBBCOM smart controller as a desktop station by installing the included kickstand (see Figure

2). Handset units must be setup horizontally. Configure hands-free units vertically or horizontally (based

on programming).

1. Remove the cable termination cover and set it aside.

2. Complete the necessary cable terminations as described in the Wiring section.

3. Route the terminated wires through the half round access holes and secure with a tie wrap to the

integrated anchors.

4. Replace the cable termination cover by hooking the two tabs into the slots and rotating the cover

downward until it clicks into place.

5. Install the kickstand:

The kickstand provides four positions in

both orientations to suit the situation

where it is used (see Table 1 and Figure

4).

1. Determine the orientation of the unit.

2. Insert one side of the kickstand, with

the flange properly oriented, into the

desired position in the rear cutout (see

Figure 4).

3. Press the other side into place and

compress firmly to snap it into place.

Figure 2. Smart Controlle

Kickstan

Pub. 42004-532E

HUBBCOM™ GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 4 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

Table 1. Smart Controller Kickstand Positions

Orientation/

Position

Horizontal

(Models GSC1100 & GSC2100)

Vertical

(Model GSC2100)

1 (flange up) 75° 75°

2 (flange up) 60° 60°

2 (flange down) 45° 45°

3 (flange up) 30° 30°

Wall Mounting

Wall mount HUBBCOM smart controllers on a single or double gang electrical box or directly to a wall

surface using wall anchors or toggle bolts.

Single or double gang electrical box mounting:

1. Orient the wall-mount bracket (see

Figure 3) over the electrical box with

the small flanges on top and the large

flanges on the bottom.

2. Use #8-32 flathead machine screws

(not included) to attach the mounting

bracket to the electrical box using

holes A-A for a double gang (four

screws), or B-B for a single gang

electrical box (two screws).

3. Feed the cable(s) into the electrical box

and through the mounting bracket

center hole.

4. Remove and discard the cable

termination cover from the back of the

unit.

5. Remove the two #8 × ½-inch mounting

bracket screws from the bottom of the

rear panel and set aside (see Figure 4).

6. Complete all necessary cable

terminations (see the Wiring section).

7. With the proper orientation for the unit’s configuration, angle the unit to hook it onto the top flange

brackets (D-D or E-E, see Figure 4), then rotate and slide it downward until it rests on the mounting

bracket.

8. Secure the unit to the support bracket using the two #8 × ½-inch screws previously removed by

screwing them into the unit’s chassis through the holes in the bottom flanges.

Figure 3. Smart Controller Wall-Mount Bracket

Pub. 42004-532E

HUBBCOM™ GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 5 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

Surface mounting with toggle bolts or wall anchors:

1. Orient the support bracket on the wall with the small flanges on top and the large flanges on the

bottom.

Suggested mounting height is 48 inches from the floor to the bottom of the mounting bracket.

2. Mark the locations (C) for the four wall anchors or toggle bolts (not included) and the area in the

center of the bracket where the cable(s) come through the wall using the support bracket as a template

(see Figure 3).

3. Drill the necessary holes for the toggle bolts or wall anchors and cut or drill a hole in the center area

for the smart controller’s cables.

4. Attach the mounting bracket to the wall using toggle bolts or wall anchors (not included).

5. Bring the cable(s) out through the support bracket center cutout.

6. Remove and discard the cable termination cover from the back of the unit.

7. Remove the two #8 × ½-inch mounting bracket screws from the bottom of the rear panel and set aside

(see Figure 4).

Figure 4. HUBBCOM Smart Controller—Rear View

8. Complete all necessary cable terminations (see the Wiring section).

9. With the proper orientation for the unit’s configuration, angle the unit to hook it onto the top flange

brackets (D-D or E-E, see Figure 4), then rotate and slide it downward until it rests on the mounting

bracket.

10. Secure the unit to the support bracket using the two #8 × ½-inch screws previously removed by

screwing them up into the unit’s chassis through the holes in the bottom flanges.

Pub. 42004-532E

HUBBCOM™GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 6 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

Wiring

HUBBCOM smart controllers have quick release terminal blocks that accept 18–24 AWG wires. Release

wires from the terminal block by pressing the quick release button above the terminal.

NOTE:Two clamp on ferrite cores are supplied with the unit. Double wrap all wires terminating to

terminal blocks TB1 and/or TB2 around a ferrite core. Install the clamp on ferrite cores as close

as possible to the terminal blocks.

Handset

1. Plug the RJ12 handset connector into the RJ12 jack on the back of the unit.

2. Wall-mount installations—Tuck the handset cord into the channel to provide strain relief for the

RJ12 plug.

RTU Input/Output

Terminal Block TB1 is for optional RTU I/O (Remote Terminal Unit Input/Output) functionality.

Complete the following steps to terminate the RTU I/O cables:

1. Install appropriately sized ferrules onto the wire ends.

2. Install a clamp on ferrite core around all wires (double wrap) terminating to TB1 as close as possible

to the terminal block.

3. Insert each wire into the correct quick release terminal (see Table 2).

Table 2. Terminal Block TB1—RTU I/O

Purpose

Term-Block Pin

Label

RTU Input One Ground

TB1-1

GND

RTU Input One

TB1-2

IN1

RTU Input Two Ground

TB1-3

GND

RTU Input Two

TB1-4

IN2

RTU Output One +

TB1-5

OUT1+

RTU Output 1 −

TB1-6

OUT1(−)

RTU Output 2 −

TB1-7

OUT2(−)

RTU Output 2 +

TB1-8

OUT2+

RS-485 and External Speaker Connections

Terminal Block TB2 is for optional RS-485 and external speaker connections. Complete the following

steps to terminate the RS-485 and external speaker connections:

NOTE:Smart controllers with external speaker hook-ups require a separate 24 V dc power supply.

1. Install appropriately sized ferrules onto the wire ends.

2. Install a clamp on ferrite core around all wires (double wrap) terminating to TB2as close as possible

to the terminal block.

3. Insert each wire into the correct quick release terminal (see Table 3).

Pub. 42004-532E

HUBBCOM™GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 7 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

Table 3. Terminal Block TB2—RS-485 and External Speaker

Purpose

Term-Block Pin

Label

RS485 Ground

TB2-1

GND

RS485 B

TB2-2

RS485B

RS485 A

TB2-3

RS485A

External Speaker −

TB2-4

SPKR−

External Speaker +

TB2-5

SPKR+

Ethernet

HUBBCOM smart controllers have dual Ethernet ports. Use the RJ45 jack furthest from the USB port to

connect to the Ethernet network. The RJ45 jack closest to the USB port can be used to connect a PC (see

Figure 4).

1. Plug the Ethernet cable from the network into the RJ45 port furthest from the USB port.

2. (Optional) Plug an Ethernet cable from a PC into the remaining RJ45 jack(see Figure 4).

24 V DC Power

Use external 24 V dc power in place of POE (optional) or for units with external speaker hook-ups

(required). Complete the following steps to terminate the 24 V dc power source to the smart controller:

1. Install ferrules onto the wire ends.

2. Insert each wire into the correct quick release terminal (see Table 4).

Table 4. Terminal Block TB3—24 V DC Power

Purpose

Term-Block Pin

Label

24 V dc Positive

TB3-1

+24V

Ground

TB3-2

GND

Antenna

Use the provided SMA (Sub-Miniature connector A) coaxial connector to connect an antenna.

NOTE:Connecting a HUBBCOM smart controller via WiFi disables the secondary Ethernet port.

NOTE:Use a customer-supplied antenna in flush-mount installations. FCC, IC, ETSI/CE, and TELEC

Certified with PCB, Dipole, Chip, and PIFA Antennae. GAI-Tronics Kit No. 12840-001

(purchased separately) meets the antenna requirements.

Pub. 42004-532E

HUBBCOM™GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 8 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

Activation

HUBBCOM smart controllers

require activation on first power-on

and after installing any purchased

upgrades. Activate a smart

controller with or without the

presence of a DHCP server.

The GUDA is available on GAI-

Tronics’ website at https://www.gai-tronics.com. Refer to Pub. 42004-531 for information on using the

GUDA software. Refer to Pub. 42004-551 for information on HUBBCOM smart controller parameters

(see the Reference Documents section).

Activation with DHCP

1. Complete all installation steps for the HUBBCOM smart controller.

2. Apply power to the

HUBBCOM smart controller.

The HUBBCOM smart

controller takes 40–50 seconds

to boot to the device activation

screen (see Figure 5). The

screen may flicker several

times during boot-up.

3. Touch the screen in the

ACTIVATION KEY field to

display the onscreen keyboard.

4. Enter the device key provided

on the smart controller’s activation label (see Figure 6 and Figure 7).

5. Press the SUBMIT ACTIVATION KEY button on the screen (see Figure 7).

The HUBBCOM smart controller reboots to activate. The smart controller takes 40–50 seconds to

reboot. The screen may flicker several times during boot-up.

Upon reboot: smart controllers with the telephone option will display the DEVICE CONFIGURATION

INCOMPLETE screen (see Figure 8); smart controllers without the telephone option will boot to the

home screen.

6. Use the GUDA to complete the configuration of the HUBBCOM smart controller.

Figure 7. Device License Key Entered

Figure 8. Activation Complete

Figure 5. HUBBCOM Device Activation Screen

Figure 6. Device Activation Label

Pub. 42004-532E

HUBBCOM™GSC1100/GSC2100 Dual-Port DT/WM Smart Controllers Page 9 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-532E.docx

11/20

NOTE:Enter additional station parameters while activating the smart controller to save time. The

smart controller accepts and sets all entered parameters regardless of correct activation code

entry. Changing the network parameters of a HUBBCOM smart controller prevents the PC

from connecting to the smart controller until the PC’s IP address is on the same subnet as

that smart controller.

Activation without DHCP

Activate a HUBBCOM smart controller on a network without a DHCP server as follows:

1. Connect the HUBBCOM smart controller to the network.

2. Apply power to the smart controller.

•The smart controller displays the HUBBCOM screen but does not continue to the activation

screen.

•The smart controller assigns itself an APIPA (automatic private IP address) after approximately

one minute.

3. Configure a PC, with the GUDA installed, for DHCP, or manually assign a static IP address in the

APIPA range.

•A PC configured for DHCP will assign itself an APIPA after approximately one to two minutes.

•A PC configured with a static IP address in the APIPA range will boot normally.

4. Run the GUDA software.

5. Select the PC’s APIPA assigned network interface from the SELECT NETWORK INTERFACE

dropdown list.

6. Click the FIND DEVICES button to perform a device discovery in the GUDA.

An ICON for the new HUBBCOM smart controller appears when the PC can connect to it.

7. Click on the ICON for the HUBBCOM smart controller.

8. Click the CONNECT AND CONFIGURE button for the HUBBCOM smart controller.

9. Login:

•Username: gai-tronics

•Password: pageparty

10. Create a new username and password.

11. Login to the HUBBCOM smart controller with the new username and password.

12. Scroll down in the left pane and click on ACTIVATION.

13. Enter the smart controller’s activation code on the activation screen.

14. Click the APPLY button to confirm the activation code.

A REBOOT button appears next to the APPLY button.

15. Click REBOOT and confirm it.

The smart controller will reboot and will display the HUBBCOM splash screen again.

16. Verify the smart controller activates and the model number is correct

1. Click the Menu button.

2. Click the Settings button.

•The model number is on the left side above the volume controls.

•The model will show NOT SPECIFIED if the smart controller did not activate correctly.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hubbell Controller Handbücher

Hubbell

Hubbell Reversing-Plugging Control 4010 Bedienungsanleitung

Hubbell

Hubbell EnergyHUBB NX Energy Dashboard Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2200 Bedienungsanleitung

Hubbell

Hubbell Chance CRS Bedienungsanleitung

Hubbell

Hubbell Fire Pump Controller LX-1500 Bedienungsanleitung

Hubbell

Hubbell Diesel Engine Fire Pump Controller LX3000 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2100 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-2700 Bedienungsanleitung

Hubbell

Hubbell 31.130 Bedienungsanleitung

Hubbell

Hubbell Silicon Controlled Rectifier 4922c Bedienungsanleitung

Hubbell

Hubbell HBL1372D Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1800 Bedienungsanleitung

Hubbell

Hubbell CHANCE Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1900 Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics HUBBCOM GSC3100 Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence Room Controller Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence NXRCFX Series Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1700 Bedienungsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4291 Bedienungsanleitung

Hubbell

Hubbell CHANCE BPRS Bedienungsanleitung

Hubbell

Hubbell LXi-2300 Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics 013-02-0095-005 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-1200 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-2400 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung