Hubbell GAI-Tronics HUBBCOM GSC3100 Bedienungsanleitung

Pub. 42004-533F 
 
G A I - T R O N I C S ®
A H U B B E L L C O M P A N Y 
HUBBCOM™ GSC3100/GSC4100  
Dual-Port Flush-Mount Smart Controllers 
TA B L E O F CO N T E N T S 
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA 
610-777-1374 ◼800-492-1212 ◼Fax: 610-796-5954 
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS 
Confidentiality Notice.....................................................................................................................1 
General Information.......................................................................................................................1 
Important Safety Instructions.........................................................................................................1 
Security Hardware..........................................................................................................................3 
Installation ......................................................................................................................................3 
Flush-Mount Installations......................................................................................................................3 
Surface Mount Installations...................................................................................................................4 
Wiring......................................................................................................................................................5 
RTU Input/Output.................................................................................................................................5 
RS-485 and External Speaker Connections ..........................................................................................6 
Ethernet.................................................................................................................................................6 
24 V DC Power..................................................................................................................................... 7 
Antenna.................................................................................................................................................7 
Activation.........................................................................................................................................7 
Activation with DHCP............................................................................................................................7 
Activation without DHCP ......................................................................................................................8 
Service and Spare Parts..................................................................................................................9 
Reference Documents...................................................................................................................10 
Specifications ................................................................................................................................10 
Approvals.......................................................................................................................................10 

Pub. 42004-533F

G A I - T R O N I C S ®

A H U B B E L L C O M P A N Y

HUBBCOM™ GSC3100/GSC4100

Dual-Port Flush-Mount Smart Controllers

GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA

610-777-1374 ◼800-492-1212 ◼Fax: 610-796-5954

VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

Confidentiality Notice

This manual is provided solely as an installation, operation, and maintenance guide and contains sensitive

business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics

retains all intellectual property and other rights in or to the information contained herein, and such

information may only be used in connection with the operation of your GAI-Tronics product or system.

This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third

party.

General Information

This guide covers the installation of the HUBBCOM Dual-Port Flush-Mount Smart Controller, Models

GSC3100 and GSC4100. The Model GSC3100 Smart Controller includes a handset. The Model

GSC4100 Smart Controller is designed for hands-free operation and is not equipped with a handset (see

Figure 1)). See the GAI-Tronics website at https://www.gai-tronics.com for applications, system

specifications, warranty information, and the GUDA (GAI-Tronics Universal Device Application).

HUBBCOM smart controllers require activation and configuration when placed into service. Use the

GUDA (GAI-Tronics Universal Device Application) software to configure the smart controller for its

intended purpose. Pub. 42004-531 provides instructions to obtain, install, and run the GUDA software.

Refer to Pub. 42004-551 for information on HUBBCOM smart controller configuration parameters (see

the Reference Documents section).

Important Safety Instructions

•Read, follow, and retain instructions—All safety and operating instructions should be read and

followed before operating the unit. Retain instructions for future reference.

•Heed warnings—Adhere to all warnings on the unit and in the operating instructions.

•Attachments—Attachments not recommended by the product manufacturer should not be used, as

they may cause hazards.

•Servicing—Do not attempt to service this unit by yourself. Opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

•HUBBCOM Smart Controllers are designed for indoor use only.

ATTENTION

—Install equipment without modification and according to all applicable local,

national, and international electrical codes. North America - Consult the

National Electrical Code (NFPA 70), Canadian Standards Association (CSA

22.1), and local codes for specific requirements regarding your installation.

Class 2 circuit wiring must be performed in accordance with the NEC.

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 2 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

These enclosures must be installed by trained, qualified and competent personnel. Installation must

comply with state and national regulations, as well as safety practices for this type of equipment.

WARNING

—Use only 24 V dc power supplies that conform to UL/CSA/CE Class II, Double

Insulated supplies with over voltage and short circuit protection. Use only a dc

source with a 50-watt maximum output or fuse the supply with a 2-amp fuse.

EMI standards to Class B.

•Onderhoud—Probeer dit apparaat niet zelf te repareren. Het openen of verwijderen van afdekkingen

kan u blootstellen aan gevaarlijke spanning of andere gevaren. Laat alle onderhoud over aan bevoegd

onderhoudspersoneel.

•HUBBCOM Smart Controllers zijn alleen bedoeld voor gebruik binnenshuis.

AANDACHT

—Gebruik alleen 24 VDC-voedingen die voldoen aan UL / CSA / CE Klasse II,

dubbel geïsoleerde voedingen met overspanning en kortsluitbeveiliging.

Gebruik alleen een DC-bron met een maximale output van 50 W of fuseer de

voeding met een 2-ampère zekering. EMI-normen voor klasse B.

•Dépannage—N'essayez pas de réparer cet appareil vous-même. Ouvrir ou retirer les capots peut

vous exposer à des tensions dangereuses ou à d'autres dangers. Confiez toute réparation à un

personnel qualifié.

•Les contrôleurs intelligents HUBBCOM sont conçus pour une utilisation en intérieur uniquement.

ATTENTION

—Utilisez uniquement des alimentations 24 Vcc conformes à UL / CSA / CE

Classe II, des alimentations à double isolation avec protection contre les

surtensions et les courts-circuits. Utilisez uniquement une source cc avec une

sortie maximale de 50 watts ou fusionnez l’alimentation avec un fusible de 2

ampères. Normes EMI à la classe B.

•Manutenzione—non tentare di riparare l'unità da soli. L'apertura o la rimozione dei coperchi

potrebbero esporre a tensioni pericolose o altri rischi. Rivolgersi a personale qualificato per

l'assistenza.

•Gli HUBBCOM Smart Controller sono progettati esclusivamente per uso interno.

AVVERTIMENTO

—Utilizzare solo alimentatori a 24 V cc conformi a UL / CSA / CE Classe II,

alimentatori a doppio isolamento con protezione da sovratensione e

cortocircuito. Utilizzare solo una fonte di corrente continua con un'uscita

massima di 50 watt o collegare l'alimentazione con un fusibile da 2 A.

Standard EMI per la classe B.

•Mantenimiento—no intente reparar esta unidad por sí mismo. Abrir o quitar las cubiertas puede

exponerlo a un voltaje peligroso u otros peligros. Remita todo el servicio a personal de servicio

calificado.

•Los controladores inteligentes HUBBCOM están diseñados para uso en interiores solamente.

ADVERTENCIA

—Utilice solo fuentes de alimentación de 24 V cc que cumplan con UL / CSA /

CE Clase II, fuentes con doble aislamiento con sobretensión y protección

contra cortocircuitos. Utilice solo una fuente de CC con una salida máxima

de 50 vatios o fusione la fuente con un fusible de 2 amperios. Estándares

EMI a Clase B.

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 3 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

Security Hardware

The HUBBCOM smart controllers described in this manual are vandal resistant. Security screws attach

the front panel of each smart controller to its enclosure. Use a GAI-Tronics Model 233-001 security

screwdriver or Torx T-25 security head tip (sold separately) to install the telephone.

Installation

Flush mount HUBBCOM smart controllers in a wall or stanchion using the included backbox or surface

mount them using a GAI-Tronics Model 236 Series or Model 238-001 Stainless-Steel Surface-Mount

Enclosure (sold separately).

NOTE: HUBBCOM devices require access to an SNTP (simple network time protocol) server.

Figure 1. HUBBCOM Model GSC3100 and Model GSC4100 Smart Controllers

Flush-Mount Installations

Use the supplied backbox when mounting the HUBBCOM smart controller in a GAI-Tronics Model 234

Series Tower and for flush-mount installations:

1. Remove the backbox from the smart controller by removing the six #10-32 security screws and

washers holding them together.

2. Remove a tapered plug from one of the rear cable entry holes in the backbox.

3. Install a cable strain relief cable fitting to the box.

4. Feed the Ethernet cable and all additional cables through the cable fitting.

5. Mount the backbox to the structure using appropriate hardware (see Figure 3 for cutout dimensions).

6. Complete all necessary cable terminations (see the Wiring section).

7. Secure the smart controller to the backbox mounting flanges using the six security screws with

washers removed in Step 1.

8. Tighten the screws to 10–12 in∙lb.

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 4 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

Surface Mount Installations

Use a GAI-Tronics Model 236 Series or Model 238-001 Enclosure to surface mount the HUBBCOM

smart controller:

1. Refer to Pub. 42004-285 for the Model 236 Series or Pub. 42004-434 for the Model 238-001

backboxes to install the surface-mount enclosure (see the Reference Documents section). GAI-

Tronics publications are located on the GAI-Tronics website at https://www/gai-tronics.com.

2. Remove and discard the backbox installed on the smart controller by removing the six security screws

and washers. Retain the six security screws and washers.

3. Complete all necessary cable terminations (see the Wiring section).

4. Secure the smart controller to the surface-mount enclosure using the six security screws and washers

removed in Step 2.

5. Tighten the screws to 10–12 in∙lb.

Figure 2. Flush-Mount Smart Controller Back Box Mounting Details

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 5 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

Figure 3. Flush-Mount Cutout Details

Wiring

HUBBCOM smart controllers have quick release terminal blocks that accept 18–24 AWG wires. Release

wires from the terminal block by pressing the quick release button above the terminal.

NOTE: Two clamp on ferrite cores are supplied with the smart controller. Double wrap all wires

terminating to terminal blocks TB1 and/or TB2 around a ferrite core. Install the clamp on ferrite

cores as close as possible to the terminal blocks.

RTU Input/Output

Terminal block TB1 is for optional RTU I/O (Remote Terminal Unit Input/Output) functionality.

Complete the following steps to terminate the RTU I/O cables:

1. Install appropriately sized ferrules onto the wire ends.

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 6 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

2. Install a clamp on ferrite core around all wires (double wrap) terminating to TB1 as close as possible

to the terminal block.

3. Insert each wire into the correct quick release terminal (see Table 1).

Table 1. Terminal Block TB1—RTU I/O

Purpose

Label

RTU Input One Ground

GND

RTU Input One

IN1

RTU Input Two Ground

GND

RTU Input Two

IN2

RTU Output 1 +

OUT1+

RTU Output 1 −

OUT1(−)

RTU Output 2 −

OUT2(−)

RTU Output 2 +

OUT2+

RS-485 and External Speaker Connections

Terminal block TB2 is for optional RS-485 and external speaker connections. Complete the following

steps to terminate the RS-485 and/or external speaker connections:

NOTE:Smart controllers with external speakers require external 24 V dc power.

1. Install appropriately sized ferrules onto the wire ends.

2. Install a clamp on ferrite core around all wires (double wrap) terminating to TB2as close as possible

to the terminal block.

3. Insert each wire into the correct quick release terminal (see Table 2).

Table 2. Terminal Block TB2—RS-485 and External Speaker

Purpose

Label

RS485 Ground

GND

RS485 B

RS485B

RS485 A

RS485A

External Speaker −

SPKR−

External Speaker +

SPKR+

Ethernet

HUBBCOM smart controllers have dual Ethernet ports. Use the RJ45 jack furthest from the USB port to

connect to the Ethernet network. The RJ45 jack closest to the USB port can be used to connect a PC.

1. Plug the Ethernet cable from the network into the RJ45 jack furthest from the USB port.

2. Install a clamp on ferrite core as close as possible to the RJ45 plug.

3. (Optional) Plug an Ethernet cable from a PC into the remaining RJ45 jack.

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 7 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

24 V DC Power

Use external 24 V dc power in place of POE (optional) or for smart controllers with external speaker

hook-ups (required). Complete the following steps to terminate the 24 V dc power source to the smart

controller:

1. Install appropriately sized ferrules onto the wire ends.

2. Insert each wire into the correct quick release terminal (see Table 3).

Table 3. Terminal Block TB3—24 V DC Power

Purpose

Label

24 V dc Positive

TB3-1

+24V

Ground

TB3-2

GND

Antenna

Use the provided SMA (Sub-Miniature connector A) coaxial connector to connect an antenna.

NOTE:Connecting a HUBBCOM smart controller via WiFi disables the secondary Ethernet port.

NOTE:Use a customer-supplied antenna in flush-mount installations. FCC, IC, ETSI/CE, and TELEC

Certified with PCB, Dipole, Chip, and PIFA Antennae. GAI-Tronics Kit No. 12840-001

(purchased separately) meets the antenna requirements.

Activation

HUBBCOM smart controllers

require activation on first power-on

and after installing any purchased

upgrades. Activate a smart

controller with or without the

presence of a DHCP server.

The GUDA is available on GAI-

Tronics’ website at https://www.gai-tronics.com. Refer to Pub. 42004-531 for information on using the

GUDA software. Refer to Pub. 42004-551 for information on HUBBCOM smart controller parameters

(see the Reference Documents section).

Activation with DHCP

1. Complete all installation steps for the HUBBCOM smart controller.

2. Apply power to the HUBBCOM smart controller.

The HUBBCOM smart controller takes 40–50 seconds to boot to the device activation screen (see

Figure 4). The screen may flicker several times during boot-up.

3. Touch the screen in the ACTIVATION KEY field to display the onscreen keyboard.

4. Enter the device key provided on the smart controller’s activation label (see Figure 5 and Figure 6).

5. Press the SUBMIT ACTIVATION KEY button on the screen (see Figure 6).

Figure 4. HUBBCOM smart controller Activation Screen

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 8 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

The HUBBCOM smart controller

will reboot to activate. The smart

controller takes 40–50 seconds to

reboot before the device

configuration notification screen

displays (see Figure 7). The screen

may flicker several times during

boot-up.

6. Use the GUDA to complete the

configuration of the HUBBCOM

smart controller.

NOTE:Enter additional station

parameters while

activating the smart controller to save time. The smart controller accepts and sets all entered

parameters regardless of correct activation code entry. Changing the network parameters of

a HUBBCOM smart controller prevents the PC from connecting to the smart controller until

the PC’s IP address is on the same subnet as that smart controller.

7. Connect additional HUBBCOM smart controllers to the network and repeat the procedure to activate

and configure them.

Activation without DHCP

Activate a HUBBCOM smart controller on a network without a DHCP server as follows:

1. Connect the HUBBCOM smart controller to the network.

2. Apply power to the smart controller.

•The smart controller displays the HUBBCOM screen but does not continue to the activation

screen.

•The smart controller assigns itself an APIPA (automatic private IP address) after approximately

one minute.

3. Configure a PC, with the GUDA installed, for DHCP, or manually assign a static IP address in the

APIPA range.

•A PC configured for DHCP will assign itself an APIPA after approximately one to two minutes.

•A PC configured with a static IP address in the APIPA range will boot normally.

4. Run the GUDA software.

Figure 6. Device License Key Entered

Figure 7. Activation Complete

Figure 5. Device Activation Label

Pub. 42004-533F

HUBBCOM™ GSC3100/GSC4100 Dual-Port Flush-Mount Smart Controllers Page 9 of 10

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-533F.docx

11/20

5. Select the PC’s APIPA assigned network interface from the SELECT NETWORK INTERFACE

dropdown list.

6. Click the FIND DEVICES button to perform a device discovery in the GUDA.

An ICON for the new HUBBCOM smart controller appears when the PC can connect to it.

7. Click on the ICON for the HUBBCOM smart controller.

8. Click the CONNECT AND CONFIGURE button for the HUBBCOM smart controller.

9. Login:

•Username: gai-tronics

•Password: pageparty

10. Create a new username and password.

11. Login to the HUBBCOM smart controller with the new username and password.

12. Scroll down in the left pane and click on ACTIVATION.

13. Enter the smart controller’s activation code on the activation screen.

14. Click the APPLY button to confirm the activation code.

A REBOOT button appears next to the APPLY button.

15. Click REBOOT and confirm it.

The smart controller will reboot and will display the HUBBCOM splash screen again.

16. Verify the smart controller activates and the model number is correct

1. Click the Menu button.

2. Click the Settings button.

•The model is shown on the left side above the volume controls.

•The model will show NOT SPECIFIED if the smart controller is not activated.

17. Use the GUDA to complete the configuration of the HUBBCOM smart controller.

NOTE:Enter additional station parameters while activating the smart controller to save time. The

smart controller accepts and sets all entered parameters regardless of correct activation code

entry. Changing the network parameters of a HUBBCOM smart controller prevents the PC

from connecting to the smart controller until the PC’s IP address is on the same subnet as

that smart controller.

18. Connect additional HUBBCOM smart controllers to the network and repeat the procedure to activate

and configure them.

Service and Spare Parts

Contact a regional service center for assistance if the equipment requires service or spare parts. A return

authorization number (RA#) will be issued if service is required. Ship equipment prepaid to GAI-Tronics

with an RA# and a purchase order number. Repair or a replacement is made in accordance with GAI-

Tronics’ warranty policy if the equipment is under warranty. Please include a written explanation of all

defects to assist our technicians in their troubleshooting efforts. Call 800-492-1212 inside the USA or

610-777-1374 outside the USA for help with identifying the Regional Service Center closest to you.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hubbell Controller Handbücher

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2900 Bedienungsanleitung

Hubbell

Hubbell Load:Logic Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence NXRCFX Series Bedienungsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4295 Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence Room Controller Bedienungsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4296 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1800 Bedienungsanleitung

Hubbell

Hubbell Diesel Engine Fire Pump Controller LX3000 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-2700 Bedienungsanleitung

Hubbell

Hubbell CHANCE BPRS Bedienungsanleitung

Hubbell

Hubbell EnergyHUBB NX Energy Dashboard Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2200 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1900 Bedienungsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4291 Bedienungsanleitung

Hubbell

Hubbell HBL1372D Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-2400 Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics 013-02-0095-005 Bedienungsanleitung

Hubbell

Hubbell Chance CRS Bedienungsanleitung

Hubbell

Hubbell GAI-TRONICS E3 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1300 Bedienungsanleitung

Hubbell

Hubbell Silicon Controlled Rectifier 4922c Bedienungsanleitung

Hubbell

Hubbell 31.130 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2100 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-1200 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung