Hubbell GAI-Tronics 013-02-0095-005 Bedienungsanleitung

Pub. 42004-563A 
 
G A I - T R O N I C S ®
A H U B B E L L C O M P A N Y 
Models 013-02-0095-005/-006  
E3 System Controllers 
TA B L E O F CO N T E N T S 
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA 
610-777-1374 ◼800-492-1212 ◼Fax: 610-796-5954 
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS 
Confidentiality Notice.....................................................................................................................1 
General Information.......................................................................................................................1 
System Types...........................................................................................................................................2 
Single System (Standalone)..................................................................................................................2 
Hot Standby (N+1) System...................................................................................................................2 
Duplicate (A/B) System........................................................................................................................ 2 
Important Safety Instructions................................................................................................................3 
Front Panel Indicators & Control.........................................................................................................3 
Rear Panel Connections .........................................................................................................................4 
Internal Connections ..............................................................................................................................5 
Installation ......................................................................................................................................6 
Installation Safety Guidelines................................................................................................................6 
Installation Guidelines............................................................................................................................6 
Mounting..................................................................................................................................................6 
Field Connections...........................................................................................................................6 
Input Power.............................................................................................................................................6 
Fuses.........................................................................................................................................................7 
Earth ........................................................................................................................................................7 
Power Out................................................................................................................................................7 
Amplifiers................................................................................................................................................7 
Generic Amplifier Interface (GAI)........................................................................................................8 
Network....................................................................................................................................................9 
Analog PABX Connection......................................................................................................................9 
API (Access Panel Interface)..................................................................................................................9 
A/B Link.................................................................................................................................................10 
Input/Output Modules..........................................................................................................................11 
Aux Audio 1...........................................................................................................................................12 
Aux Audio 2...........................................................................................................................................13 
Operation.......................................................................................................................................13 

Table of Contents Pub. 42004-563A 
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA 
610-777-1374 ◼800-492-1212 ◼Fax: 610-796-5954 
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS 
Status LEDs...........................................................................................................................................13 
Telephone Access ..................................................................................................................................14 
Reference Documentation ............................................................................................................14 
Specifications ................................................................................................................................14 
Electrical................................................................................................................................................14 
System Limitations (Maximums).........................................................................................................15 
Power Amplifier Audio Outputs..........................................................................................................15 
A/B Interlink..........................................................................................................................................15 
Audio Outputs (Event Record A/B, Monitor Out, Aux Out)............................................................15 
Page/Party Interface.............................................................................................................................15 
Auxiliary Audio Input 1–3 ...................................................................................................................15 
Data Communications..........................................................................................................................16 
Control Input—Aux 1...........................................................................................................................16 
Status LEDs...........................................................................................................................................16 
Terminals...............................................................................................................................................16 
Environmental.......................................................................................................................................16 
Mechanical.............................................................................................................................................16 
Approvals.......................................................................................................................................16 
 

Pub. 42004-563A

GAI-TRONICS®

A HUBBELL COMPANY

E3 System Controllers

GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA

610-777-1374  800-492-1212  Fax: 610-796-5954

VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

Confidentiality Notice

This installation, operation, and maintenance manual contains sensitive business and technical

information that is confidential and proprietary to GAI-Tronics. GAI-Tronics retains all intellectual

property and other rights in or to the information contained herein, and such information may only be

used in connection with the operation of your GAI-Tronics product or system. This manual may not be

disclosed in any form, in whole or in part, directly or indirectly, to any third party.

Page/Party® is a registered trademark of GAI-Tronics Corporation.

General Information

The Model 013-02-0095-005 and 013-02-0095-006 E3 System Controllers are central components in

Elemec3 PAGA (public address and general alarm) systems. They are for use where failsafe operation is

imperative but are also suitable for a wide variety of other communication and control applications.

Figure 1. Elemec3 System Controller

E3 system controllers are data acquisition, audio signal processing, and control devices. An E3 system

controller continuously monitors the integrity of its Elemec3 system and immediately reports changes in

activity or system health. The controller sends and receives data and test signals to and from connected

equipment to provide a reliable, high integrity system. The system monitors access panels, Elemec power

amplifiers, audio paths, alarm inputs, beacon outputs, and other system components.

The Model 013-02-0095-005 System Controller includes an analog telephone interface PCBA and a SIP

telephone interface, making it capable of receiving incoming calls from either analog or IP telephone

Pub. 42004-563A

E3 System Controllers Page 2 of 16

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-563A.docx

01/21

systems. The Model 013-02-0095-006 includes only the SIP telephone interface for connection to an IP

telephone system.

The E3 system controller’s Ethernet interface provides a SIP telephone interface, enabling reception of

VoIP telephone calls by the E3 controller. This provides programmable access to the PA system (usually

at the lowest priority level). Allocate a dedicated IP-PBX extension for this service.

Configure an Elemec3 system controller in the following ways to provide the required level of system

redundancy: 1) Single system (standalone), 2) Hot standby system (N+1), and 3) Duplicate system (A/B)

(see the System Types section).

Use the Elemec3 Console application to configure the E3 system, via a TCP/IP network connection.

Use the Elemec3 Portal software application to monitor system status, including current audio activity,

faults, inputs, outputs, and amplifier states via a TCP/IP network connection. The system controller

contains an internal clock to enable a time stamp on event logs when the status of the system changes,

such as an alarm event.

To eliminate the possibility of acoustic feedback, configure the system to replay digitally recorded audio

from access panels, PABX systems, Page/Party systems, and VoIP telephones.

Individually program up to 256 inputs and 256 outputs. Connect up to 16 wired access panels for speech

broadcasts and manual alarm/emergency message activation. Additional audio inputs/outputs are

available to accommodate connections to/from ancillary equipment.

The system has two audio paths to enable two simultaneous broadcasts.

Install the controllers in a standard 19-inch rack for ease of installation and maintenance. All connections

to the controller are a plug/socket type.

System Types

Configure the Elemec3 system controller in one of three ways: 1) Single System (Standalone), 2) Hot

Standby System (N+1), or 3) Duplicate System (A/B). Refer to the system manual included with the

Elemec3 system for detailed information on that system’s configuration.

Single System (Standalone)

In a single type system, a single Elemec3 system controller controls the system’s amplifiers, access

panels, and I/O devices.

Hot Standby (N+1) System

In a redundant N+1 system, two controllers, designated as primary and secondary, control a single set of

amplifiers. Duplicate access panels and I/O devices have connections to both controllers.

Automatic switchover (hot standby) amplifier control automatically connects spare amplifiers to the

loudspeaker network of failed amplifiers.

Duplicate (A/B) System

In a duplicated or redundant system, two Elemec3 system controllers, designated as Aand B, control two

sets of amplifiers (also designated as A and B) with two speaker lines run in different routes. Duplicate

access panels and I/O devices have connections to both the A and B controllers. Locate duplicate systems

together or at two separate locations, each housing either the A or B system.

Pub. 42004-563A

E3 System Controllers Page 3 of 16

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-563A.docx

01/21

Important Safety Instructions

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this equipment near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Only use attachments/accessories specified by the manufacturer.

• Refer all servicing to qualified service personnel. Servicing is required when the equipment has been

damaged in any way. This includes, but is not limited to; power-supply cord or plug damage,

exposure to rain, moisture, or liquid intrusion into the equipment, the equipment has been dropped or

has sustained a severe shock, or fails to operate normally for any reason.

Front Panel Indicators & Control

The E3 system controller front panel has an auto alarm inhibit key switch, three LED indicators, and a

USB port (the USB port is not functional in this product). When the auto alarm inhibit key switch is in

the ON position, it prevents activation of alarm events from configured I/O module inputs. The LEDs

indicate if the system is in use, if power is present, and if the system is operating normally or has a fault

condition.

Figure 2. Elemec3 System Controller—Front View

Pub. 42004-563A

E3 System Controllers Page 4 of 16

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-563A.docx

01/21

Rear Panel Connections

Make all system connections at the rear of the E3 system controller (see Figure 3).

USC

LISTED

USC

LISTED

Figure 3. E3 System Controller—Rear View

Pub. 42004-563A

E3 System Controllers Page 5 of 16

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-563A.docx

01/21

Internal Connections

All internal connections are plug and socket connections. The following figures show the internal

components of the two controller models.

Figure 4. Model 013-02-0095-005 System Controller—Internal Components—Top View

Figure 5. Model 013-02-0095-006 System Controller—Internal Components—Top View

Pub. 42004-563A

E3 System Controllers Page 6 of 16

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-563A.docx

01/21

Table 1. Elemec3 System Controller—Internal Components

Component

Description

Digital PCBA

Central processing unit, digital communications, speech recording, and

play-back to eliminate feedback

Analog PCBA

Audio amplification and routing

Telephone Interface PCBA

(-003 version only)

Interface from the Elecmec3 system controller to the telephone system

Elemec3 Fuse PCBA

Protection for the system controller, access panel interfaces, and I/O

modules

Installation

Installation Safety Guidelines

Please adhere to all warnings, safety, and operating instructions on the unit and in the installation manual.

WARNING

•Disconnect power before servicing—Do not disconnect the equipment while the circuit is energized.

•Avoid servicing the unit during electrical storms.

•Do not touch uninsulated wires.

Installation Guidelines

•Notify plant personnel of a system shutdown prior to servicing the unit.

•Disconnect power before installing or removing the system controller.

Mounting

Mount the Elemec3 System Controller in the 19-inch rack using the supplied hardware. Each controller is

1.75 inches tall/1 U of rack height.

Field Connections

Input Power

The controller requires a 24 V dc power source capable of delivering 6.4 amps minimum.

1. Remove the two-position plug from the 24VDC IN header (see Figure 3).

2. Screw the dc power cable to the plug.

Observe the polarity marking on the rear of the unit.

3. Install the plug into the 24VDC IN header.

Power applied to the 24VDC IN connector also powers the access panel interfaces, access panels, and

the I/O modules.

Pub. 42004-563A

E3 System Controllers Page 7 of 16

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-563A.docx

01/21

Fuses

The E3 system controller includes a fuse for each device that receives power from the controller (see

Table 2). Use only IEC time-delayed fuses with the appropriate ratings.

Table 2. Fuse Information and Ratings

Fuse

Description

Output

Rating

Auxiliary Power Output

24 V DC OUT

T2.5A 250V

System Controller

N/A

T1A 250V

Access Panel Interface—Group 1

API 1

T500mA 250V

Access Panel Interface—Group 2

API 2

T500mA 250V

Access Panel Interface—Group 3

API 3

T500mA 250V

Access Panel Interface—Group 4

API 4

T500mA 250V

Access Panel Interface—Group 5A & 5B

API 5A/B

T500mA 250V

Input / Output Modules

I/O

T1.6A 250V

NOTE:Each access panel interface has T100mA 250V fuses to limit the current to each access panel.

Earth

Install an appropriately sized green-yellow sheathed conductor between the DC EARTH terminal on the

rear of the unit and the telecoms earth bar inside the cabinet (see Figure 3).

Power Out

Supply power to additional devices via the 24VDC OUT connector (see Figure 3).

1. Remove the two-position plug from the 24VDC OUT header.

2. Screw the dc power cable to the plug.

observe polarity (marked on the rear of the unit).

3. Install the plug back into the 24VDC OUT header (See F1 in Table 2).

Amplifiers

Elemec3 system controllers connect to Elemec3 power amplifiers via a 10-conductor IDC ribbon cable,

installed between the AMPLIFIER LINK connector on the controller and the AMP CONTROL connector on

the power amplifier(s). The Elemec3 system controller is compatible with the following Elemec3 power

amplifiers:

•D300i

•D550i

•D600i

Refer to the amplifier manual included with the Elemec3 system for installation, operation, and

maintenance information of the installed amplifiers (see Figure 6 for a typical system controller to power

amplifier connection).

Pub. 42004-563A

E3 System Controllers Page 8 of 16

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-563A.docx

01/21

WARNING —The generic amplifier interface does not contain monitoring and/or fault status

reporting of the generic power amplifiers. DO NOT USE power amplifiers

connected to a generic amplifier interface for critical communications requiring

amplifier supervision.

USC

LISTED

Figure 6. Elemec3 Power Amplifier Connection

Generic Amplifier Interface (GAI)

Connect up to 16 generic amplifier interfaces to an E3 system controller. The GAI allows connection of

alternate amplifiers not specified above for use in the Elemec3 system. Install a 10-conductor IDC ribbon

cable between the amplifier link header of the controller and the CI header on the generic amplifier

interface(s) (see Figure 7). Refer to the generic amplifier interface manual included with the Elemec3

system for installation, operation, and maintenance information of installed generic amplifier interfaces.

USC

LISTED

Figure 7. Generic Amplifier Interface Connection

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hubbell Controller Handbücher

Hubbell

Hubbell Euclid Lifting Magnet Controller 4296 Bedienungsanleitung

Hubbell

Hubbell 31.130 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1900 Bedienungsanleitung

Hubbell

Hubbell LXi-1100 Bedienungsanleitung

Hubbell

Hubbell HBL1372D Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence NXRCFX Series Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-2400 Bedienungsanleitung

Hubbell

Hubbell EnergyHUBB NX Energy Dashboard Bedienungsanleitung

Hubbell

Hubbell Diesel Engine Fire Pump Controller LX3000 Bedienungsanleitung

Hubbell

Hubbell Load:Logic Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence Room Controller Bedienungsanleitung

Hubbell

Hubbell T1000 Betriebsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1700 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-2700 Bedienungsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4295 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2800 Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics HUBBCOM GSC1100 Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics HUBBCOM GSC3100 Bedienungsanleitung

Hubbell

Hubbell LXi-2300 Bedienungsanleitung

Hubbell

Hubbell GAI-TRONICS E3 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1400 Bedienungsanleitung

Hubbell

Hubbell Silicon Controlled Rectifier 4922c Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2100 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2200 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch