Hubbell Load:Logic Bedienungsanleitung

PD2794 02/2017 Page 1

Room Controller

Installation Instructions

Precautions

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

CAUTION: USE COPPER CONDUCTOR ONLY.

CAUTION - RISK OF ELECTRICAL SHOCK. To prevent electrical shock, turn OFF power at the circuit breaker

before installing or servicing unit. Never wire energized electrical components.

NOTICE: For installation by a licensed electrician in accordance with National and/or local Electrical Codes and the

following instructions.

NOTICE: Do not install if product appears to be damaged.

Be sure to read and understand all instructions before installing or servicing unit

For Indoor use only. Do not use outdoors.

Disconnect switch or a circuit breaker must be provided and marked as the disconnecting device.

The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

Confirm device ratings are suitable for application prior to installation. Use of device in applications beyond its specified

ratings or in applications other than its intended use may cause an unsafe condition and will void manufacturer’s

warranty.

All servicing shall be performed by qualified service personnel.

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment

may be impaired.

No user serviceable parts contained inside unit. Refer all service related questions to the factory.

SAVE THESE INSTRUCTIONS!

PD2795 02/2017 Page 1

Room Controller Setup App

Operation Guide

IMPORTANT: This App is designed to assist in the configuration of control parameters for the Hubbell Wiring Device-Kellems

Load:Logic®Room Controller. Once the App has been used to change any setting in a room, manual configuration using the push

buttons and LEDs on the Room Controller will be disabled. All further settings will need to be made using the App. (See Room

Controller Installation Instructions)

START THE APP BY TOUCHING THE NX SCREEN ICON.

When the App starts, you will be prompted to enter a security pin. The default pin is 96@01.

Once started, the App will automatically do a discovery to find all active RCBTM’s (NXBTR)

Bluetooth®interface modules that are in range. After discovery is complete, a list of discovered

RBTM’s will be displayed. Use the signal strength indicators to determine the closest module for

the current room. Modules can also be uniquely identified by the MAC address label on the

module’s housing.

Touch the appropriate module indicator to start a discovery of devices in the room where this

module is installed. Wait for the discovery to complete before making further selections.

When discovery is complete, a listing of the devices found will be displayed. These will include:

1. Room Controllers: Touch to display a list of room controllers found in the room. Touch

one of the room controllers to see a display showing controls for the relay(s) and

dimmer(s), if present, in that room controller. If the room has only one room controller, it

will automatically open when Room Controllers is selected.

The current state of the relays and dimmers will be displayed on the screen. The displays are in

real time.

Use the relay control(s) to change the state of the relay. Use the dimmer control bar to change

the state of the dimmer(s)

Reboot (Top of Screen): Restarts the room controller.

Factory Reset: Sets the room controller and all connected devices back to factory

default settings.

2. Relays: Touch to display a list of relays found in the room. Touch the relay to see a display

of the available relay settings. The current settings will be shown on the display.

Name: Allows the relay to be given a meaningful name. Use the keyboard to enter a

name if desired.

Pri/Sec: Indicates whether this relay is logically a Primary relay or a Secondary relay.

This logic is used with the daylight sensor option to determine the sequence in which

the relay(s) will switch OFF in response to increasing daylight. The Primary relay will

switch first, followed by the Secondary.

Power Up: Select the state this relay will default to upon restoration of power to the

room controller after an outage. The default setting is Last State.

PD2795 02/2017 Page 2

Mode: Indicates how the relay will respond to the occupancy sensor. Occupancy mode is automatic ON. Vacancy mode is

manual ON. This will automatically be set to Vacancy mode for all relays if at least one switch is connected to the room

controller(s).

Occupied: Sets the state of the relay when the room is occupied. Default is ON.

Unoccupied: Sets the state of the relay when the room is unoccupied. Default is OFF.

Groups: A blue background fill in one of the 16 available groups indicates that this relay is selected to be a member of this

group number. A gray background fill indicates that the relay is NOT a member of the group. The relay may be a member

of any or all groups if required.

Relay: Allows manual ON/OFF actuation of the relay in real time.

Make changes as needed. Touch the <Accept> button to save the changes or touch the <Back>

button to exit WITHOUT saving the changes.

3. Dimmers: Touch to display a list of dimmers found in the room. Touch one of the dimmers to

see a display of the dimmer settings:

Name: Allows the dimmer to be given a meaningful name. Use the keyboard to enter a

name if desired.

Power Up: Select the state this dimmer will default to upon restoration after an outage.

<Last State> is the default setting. Touch <Set Level> to enter a specific dim level for

power up. Use the <Level> slider to set the desired level or, touch the box to use the

keyboard to enter the level.

High Trim: Sets the maximum dimming level for this dimmer. The default setting is 100%.

Low Trim: Sets the minimum dimming level for this dimmer. The default setting is 0%

Dim to OFF: If set to <Enabled>, a relay(s) in the same group as the dimmer, will turn

OFF when the dimming level reaches 0%. If set to <Disabled>, a relay(s) in the same

group as the dimmer, will NOT turn OFF when the dimming level reaches 0%.

Mode: Indicates how the dimmer will respond to the occupancy sensor. Vacancy Mode

is Manual ON. Occupancy Mode is Automatic ON.

Occupied Level: Sets the Level of the dimmer when the room is occupied. Default is

Last Level.

Unoccupied Level: Sets the level of the dimmer when the room is unoccupied. Default

is Last Level.

Groups: A blue background fill in one of the 16 available groups indicates that this

dimmer is selected to be a member of this group number. A gray background fill indicates that the dimmer is NOT a

member of the group. The dimmer may be a member of any or all groups if required.

Dimmer: Allows manual actuation of the dimmer in real time.

Make changes as needed. Touch the <Accept> button to save the changes or touch the <Back>

button to exit WITHOUT saving the changes.

PD2795 02/2017 Page 3

4. Switches: Touch to display a list of switches found in the room. Note that each switch display indicates the port number and

switch’s address wheel setting (See RC Switch installation instructions for more details). This is useful for distinguishing

between switches of the same type in the room.

There are a number of different switch types that might be discovered. The setup screens for the various types will differ based on

the function of the switch being selected.

Touch a switch to see the current settings for that switch:

A. Multifunction Switch - # series smart switch:

Name: Allows the switch station to be given a meaningful name. Use the keyboard to

enter a name as desired.

Button: Blue background fill indicates the currently selected button.

Type: Indicates the current button type. The default button type is Toggle. Use the pull

down to display a list of the available button types and select the desired Type from the

list for this button:

Toggle: Touch ON/Touch OFF (default)

ON: Touch for ON only

OFF: Touch for OFF only

Raise: Ramp dimmer up

Lower: Ramp dimmer down

Timed ON: Touch for ON for set time period

Disabled: Button disabled

Groups: A blue background fill in one of the 16 available groups indicates that this switch is selected to be a member of

this group number. A gray background fill indicates that the switch is NOT a member of the group. The switch may be a

member of any or all groups if required.

Make changes as needed. Touch the <Accept> button to save the changes or touch the <Back> button to exit WITHOUT saving

the changes.

B. ON/RAISE/LOWER/OFF (ORLO) and RAISE/LOWER (RL) Switches:

Name: Allows the switch station to be given a meaningful name. Use the keyboard to enter a name as desired.

Raise/Lower Setup: Allows adjustment to the speed at which the dimming level will change as a Raise or Lower button

held down.

Rate: Sets the rate at which level change messages are sent from the switch to the

dimmer. Recommended setting is 300.

% Change: Sets the amount of change that occurs with each message. A setting of 10

will provide about a 5 second transition time from 0% to 100%.

Groups: A blue background fill in one of the 16 available groups indicates that this switch

is selected to be a member of this group number. A gray background fill indicates that the

switch is NOT a member of the group. The switch may be a member of any or all groups

if required.

Make changes as needed. Touch the <Accept> button to save the changes or touch the <Back>

button to exit WITHOUT saving the changes.

PD2795 02/2017 Page 4

C. Scene Switch:

Name: Allows the switch to be given a meaningful name. Use the keyboard to enter a name as desired.

Preset Setup: The buttons are factory configured to control Preset 1 - Preset 4 from top to bottom respectively. Use the

drop down arrow adjacent to a button to choose one of the 16 available presets to be recalled by this button.

Preset Status: Indicates the currently activated preset.

Raise/Lower Setup: Allows adjustment to the speed at which the dimming level will change as a Raise or Lower button

held down.

Rate: Sets the rate at which level change messages are sent from the switch to the dimmer. Recommended setting is

300.

% Change: Sets the amount of change that occurs with each message. A setting of 10 will provide about a 5 second

transition time from 0% to 100% while holding down a Raise or Lower button.

Make changes as needed. Touch the <Accept> button to save the changes or touch the <Back> button to exit WITHOUT saving

the changes.

5. Occupancy Sensors: Note that regardless of the quantity of sensors installed, the App will only indicate a single sensor with a

composite occupancy state for the room.

Name: Allows the sensor to be given a meaningful name. Use the keyboard to enter a name as desired.

Groups: A blue background fill in one of the 16 available groups indicates that this sensor is selected to be a member of

this group number. A gray background fill indicates that the sensor is NOT a member of the group. By default, the

occupancy sensor is set to be a member of all groups.

State: Indicates the Occupied or Unoccupied state of the room as reported by the occupancy sensor at the time the App

screen was accessed. This is read only. Touch the <Refresh> button to re-read the occupancy state of the room.

Make changes as needed. Touch the <Accept> button to save the changes or touch the <Back> button to exit WITHOUT saving

the changes.

6. Daylight Sensor: Touch to display the Photocell set up page. This page allows for the setup of up to 6 zones of daylight

harvesting using a single compatible photocell like the RCDP.

Name: Allows the sensor to be given a meaningful name. Use the keyboard to enter a

name as desired.

Daylight Level: Indicates the current amount of daylight visible to the daylight sensor.

Touch <Refresh> at any time to re -read the daylight level.

Sensor Range: Use the pull down to select the range appropriate to the daylight sensor

model installed. The standard RCDP daylight sensor is factory set to 3 to 300. This is the

nominal default for typical indoor side lighted applications.

Zone #: Use the pull down to select the type of daylight harvesting control to be used for

this zone. The available choices are:

A. None: Daylight harvesting not enabled. This is the default setting for Zones 2-6.

PD2795 02/2017 Page 5

B. ON/OFF Mode: All controlled lighting will turn OFF based on the settings. The controlled lighting will be OFF as long

as there is sufficient daylight to maintain the desired minimum task light level.

Design Level: The target minimum foot candle level at the task work surface.

At Sensor: Indicates the current amount of daylight visible to the daylight sensor. Touch <Get Level> at any time

to refresh the daylight level.

At Task: The amount of light in foot candles as read by a light meter placed at the task surface. Take this reading

with the indoor lighting turned OFF.

Dead Band (%): Provides a band between ON and OFF to prevent unwanted cycling of the load. Typically a

setting of 5% works well.

Make changes as needed. Touch the <Accept> button to save the changes or

touch the <Back> button to exit WITHOUT saving the changes.

C. Step Relay Mode: High, low, OFF switching control based on the

Primary/Secondary setting for the controlled relay(s)

D. Full Dimming Mode: Full range dimming in response to daylight.

Design Level: The target minimum foot candle level to be maintained at the

work surface. Enter the specified foot candle level.

At Sensor: Indicates the current amount of daylight visible to the daylight

sensor. Touch <Get Level> at any time to re read the daylight level.

At Task: The amount of light in foot candles as read by a light meter placed at the task surface. Take this reading

with the electric lighting turned OFF.

NOTE: Make adjustments to the Design Level until the desired foot candle reading is achieved on the light meter

at the task surface.

E. Test Mode: This is the factory default setting for Zone 1. Test mode causes the controlled lighting to react quickly to

bright and dim light such as passing the beam of a flashlight across the daylight sensor.

7. Preset Settings: Touch to display the preset setup page. Use the Preset Select pull down to choose which preset (1 - 16) this

button will affect. Note: the factory default programming, sets Preset 1 to 100%, Preset 2 to 75%, Preset 3 to 50%, and Preset

4 to 25% for all dimmers. NOTE: The “Include” setting determines if this preset will affect the associated dimmer or relay. If the

box is not checked, this preset will NOT change this dimmer or relay when activated.

Fade Time: The fade time for transitions between presets can be set between 1 second and 18 hours. The factory default

fade time is 5 seconds. Use the sliders or type in the box to change the fade time for this preset.

Dimmers: Use the slider or type in the box to set the desired dimmer level for each dimmer.

Relays: Use the controls to set if the relay will be turned ON or OFF when this preset is activated.

After all settings have been selected, touch the <Save> button at the top of the screen. A <Test> button is also provided at the top

of the screen. This button will activate the current preset exactly as if the preset button on the actual switch is touched.

NOTE: Touching the <Test> button immediately after saving a preset will have no affect since the lighting will already be set to the

levels defined for the current preset.

PD2794 02/2017 Page 2

Figure 1

Room Controller mounted

into a 4 x 4 junction box

Figure 2

Room Controller RJ45 ports

to connect control devices

Description

Hubbell Wiring Device-Kellems Load:Logic®Room Controller is a smart device designed to control and manage lighting loads in

a space based on a set of configured parameters. It contains two independently controlled outputs. Optional 0-10VDC outputs

are available for controlling dimmable ballasts and LED drivers. The Load:Logic®Room Controller also features four RJ45 ports

that provide plug and play support for occupancy, daylight sensors and switches for local control. The Load:Logic® Room

Controller can operate in a stand-alone mode or connected with other room controllers.

Installation

1. DO NOT DISCARD THE MAC ADDRESS LABELS INCLUDED WITH THE

PRODUCT. SEE STEP (5) BELOW.

2. The room controller has a MAC address label affixed to the outside of the unit.

Place the enclosed MAC address label(s) in a log book and record the location of

the room controller and the circuit(s) it controls. The MAC address will be needed

later during the system setup process.

3. Turn power OFF at the service panel.

4. Mount the room controller’s enclosure to a ½” knockout opening of an electrical junction box.

Secure it to box tightening the included locknut. (See Figure 1)

5. Connect the control devices (e.g. occupancy sensors, daylight sensor and switches) to

any of the RJ45 ports available using a UTP patch cord. Similar devices (e.g. switches or

occupancy sensors) may be connected together from the same RJ45 port. (See Figure 2)

6. Make the appropriate electrical connections from the room controller to the corresponding

devices as shown in Figure 3.

7. Turn ON the power at the service panel.

8. Test the installation as follows:

a. Momentarily press Button A to toggle Load A (red wire) ON and OFF.

b. Momentarily press Button B to toggle Load B (blue wire) ON and OFF.

c. Turn ON Load A.

d. Press and hold Button A down to decrease the light level on Load A.

e. Release Button A and press again to increase the light level on Load A.

f. Turn OFF Load A.

g. Turn ON Load B

h. Press and hold Button B down to decrease the light level on Load B.

i. Release Button B and press again to increase the light level on Load B.

j. Turn OFF Load B.

PD2794 02/2017 Page 3

Understanding Low Voltage Load Capacity

The room controller is capable of providing a source of 24VDC to power the connected low voltage devices such as switches,

sensors and wireless transmitters. The room controller’s current capacity is 250 mA. Since the control components require

different amounts of current to operate properly, the following table will help to determine how many low voltage devices can be

connected to a single room controller regardless of the RJ45 port in which the device is connected. If two or more room

controllers are connected together, the capacity is determined for each room controller based on the control devices that are

actually connected into that specific room controller. The maximum capacity per room controller is 30 Loads. Below is the

correlation in regards of current requirements per low voltage device.

Switches, Daylight Photocell, and PIR Occupancy Sensor = 1 Load

PIR only Occupancy sensor with RP option = 2 Loads

Dual Technology and Ultrasonic Occupancy sensor = 3 Loads

Dual Technology and Ultrasonic Occupancy sensor with RP option = 4 Loads

NOTE: Only one daylight sensor can be connected in each room/zone

Self-Configuration

The room controller’s sequence of operation will automatically reconfigure as devices are connected as described in the

following sections. Note that self-configuration will automatically be disabled once the room has been manually configured. See

Manual Configuration section.

Occupancy Sensors

The room controller is compatible with any Hubbell Wiring Device-Kellems low voltage occupancy sensor. An RJ45 wiring

adapter (sold separately) is required to make the sensor compatible with the connection to a RJ-45 port in the room controller.

See Figure 3 and HBLRJ45A10 installation instructions. This adapter is color coded to match the flying leads on the sensors.

An occupancy sensor connected to a room controller will be recognized after the first time it cycles occupancy.

When ONLY an occupancy sensor is connected to the room controller, the room controller will set its operation mode to Auto

ON / Auto OFF. Once a smart switch is connected to the room controller, the operation mode will automatically switch to

Manual ON / Auto OFF (vacancy mode). To change one or more load(s) to Auto ON operation see Manual Configuration

section below.

Figure 3

PD2794 02/2017 Page 4

Smart Switches

These devices will automatically configure themselves to control the available loads within 5 seconds after being connected to

the room controller. For best results, do not press any buttons for 5 seconds after connecting a switch to the room controller.

The buttons on the following switch catalog numbers are configured as toggle ON/OFF operation mode by default: RCS1x,

RCS2x, RCS2x, RCS4x, and RCS6x. These switches will self configure to sequentially control the loads. For example, an

RCS1x will control Load A and Load B simultaneously because it only has one button, an RCS2x will control loads A and B,

independently because it has 2 buttons.

The relationship between the buttons and the loads can be configured. See Manual Configuration below. NOTE: If the zone

has more loads than buttons, the last button in the sequence will automatically control the all remaining loads simultaneously.

This insures that no load is left uncontrolled during the self-configuration process.

Switches with specific functions like catalog numbers RCSNFx and RCSTOx, RCSRLx, RCSSCx, RCSNRLFx will self-

configure by default to their respective descriptions. For example; RCSRLx is a Raise/Lower dimmer. Its default operation will

be to change ALL the light levels of connected light fixtures. The relationship between the switch functions and the loads being

controlled can be modified. See Manual Configuration below.

Daylight Sensor

The daylight sensor will self-configure to control Load A when connected to a room controller. The photocell operation can be

verified by observing Load A lighting while alternately covering the photocell (Load A light will be ON and bright if dimming

enabled) or exposing the photocell to bright light (Load A light will be OFF or dimmed if so enabled). The relationship between

the daylight sensor and the load(s) can be changed. See Manual Configuration below.

Figure 4

Manual Configuration

The process of manual configuration allows for the adjustment of certain functions by using the A and B pushbuttons and LED

indicators on the room controller’s enclosure. The functions that can be adjusted are:

1. Assign loads to buttons and switches.

2. Configure loads for Manual ON (vacancy mode) or Auto ON operation mode.

3. Configure loads to respond to the photocell.

4. Calibrate the photocell.

PD2794 02/2017 Page 5

How to Enter Manual Configuration Mode from the Room Controller

To enter manual configuration mode, follow these steps:

1. Simultaneously press and hold the A and B pushbuttons on the room controller until the A and B LED’s start to blink

alternately.

2. Release the A and B pushbuttons. The room controller is now in manual configuration mode. The light fixtures on the

circuit connected to Load A will be ON and all other loads will be OFF.

Note: While in configuration mode no more than one load will ever be ON and the A and B buttons on the room controller will

NOT be able to control the loads.

Hint: If both loads (A and B) are ON or pressing the A or B button switches a load, the room controller is NOT in

configuration mode. Repeat the previous steps to enter manual configuration mode.

Exit Manual Configuration Mode from the Room Controller

To exit manual configuration mode, simultaneously press and immediately release buttons A and B. The room controller will

resume normal operation.

Enter Manual Configuration Mode from a Switch

1. Remove the faceplate from any of the switches in the room and locate the rectangular opening in the plastic bezel

marked “SVC PIN”. Use a small round object such as a straightened paper clip to press the recessed configuration

button for 5 seconds.

2. Observe that the button is located slightly offset from the bezel opening. The LED marked “SVC” will blink while the

configuration button is being pressed.

3. Release the configuration button and note that one load turns ON and all other loads turn OFF indicating that the room

is in manual configuration mode.

Exit Manual Configuration Mode from a Switch

1. Press the configuration button for five seconds. The LED marked “SVC” will blink while the configuration button is

being pressed.

2. Release the configuration button. The loads in the room will restore to the levels they were prior to entering manual

configuration mode.

Assigning a Lighting Load to Buttons in a Switch

As described in the Smart Switches section, all switches assume a default operation of the loads when they are connected to

the room controller’s RJ45 port. The assignment of the loads to the buttons can easily be changed as follows:

Switches with LED indicators:

1. Enter in Manual Configuration Mode from the Switch described above. Load A will be ON. While

load A is ON, each button that controls that load will have a lighted LED.

2. To deny the control function of the load from the button, press the switch button to turn OFF the

button’s LED.

3. To assign control of the load to another button, press the switch’s button to light ON the LED the

button to be paired.

4. Repeat this process for all buttons.

5. To advance to the next load, press and release button A on the room controller. Load A will turn OFF and the next

load will turn ON.

Andere Hubbell Controller Handbücher

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2100 Bedienungsanleitung

Hubbell

Hubbell EnergyHUBB NX Energy Dashboard Bedienungsanleitung

Hubbell

Hubbell Chance CRS Bedienungsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4291 Bedienungsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4296 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-1200 Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics HUBBCOM GSC3100 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1300 Bedienungsanleitung

Hubbell

Hubbell NX Distributed Intelligence Room Controller Bedienungsanleitung

Hubbell

Hubbell 31.130 Bedienungsanleitung

Hubbell

Hubbell GAI-TRONICS E3 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1800 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2200 Bedienungsanleitung

Hubbell

Hubbell Silicon Controlled Rectifier 4922c Bedienungsanleitung

Hubbell

Hubbell CHANCE Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 1900 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi 2800 Bedienungsanleitung

Hubbell

Hubbell Diesel Engine Fire Pump Controller LX3000 Bedienungsanleitung

Hubbell

Hubbell T1000 Betriebsanleitung

Hubbell

Hubbell Euclid Lifting Magnet Controller 4295 Bedienungsanleitung

Hubbell

Hubbell CHANCE BPRS Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics 013-02-0095-005 Bedienungsanleitung

Hubbell

Hubbell GAI-Tronics HUBBCOM GSC1100 Bedienungsanleitung

Hubbell

Hubbell Electric Fire Pump Controllers LXi-2700 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch