Hubbell Dual-Lite UFO-LP1 Bedienungsanleitung

INSTALLATION INSTRUCTIONS

! IMPORTANT SAFEGUARDS !

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter

connector must be open. Do not join inverter connector until installation is complete and AC power is

supplied to the emergency ballast.

2. This product is for use with most 14W through 54W (2'- 4')T5 bipin, 22WT5 circular, 36W through 55W

(4-pin) long compact, or 32W (4-pin) compact, 32 W (4'), 40 W (5') and 44 W HO (4') T8 bipin

ﬂuorescent lamps.

3. Make sure all connections are in accordance with the National Electrical Code and any local

regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and

inverter connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or ﬁeld installation in the ballast channel or on top of ﬁxture.

6. This product is for use in indoor ﬁxtures except air handling heated air outlets, and wet, damp, or

hazardous locations.

7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not ﬁeld

replaceable. Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe

condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualiﬁed service personnel.

SAVE THESE INSTRUCTIONS

10/23/09

WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

Hubbell Lighting, Inc. • 701 Millennium Blvd • Greenville, SC 29607 • (864) 678-1000 • FAX (864) 678-1415 • www.dual-lite.com

70100524

UFO-LP1

Ni - Cd

CONTAINS NICKEL-CADMIUM

RECHARGEABLE BATTERY.

MUST BE RECYCLED OR

DISPOSED OF PROPERLY.

INSTALLATION

NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched source of power is required. The emergency ballast

must be fed from the same branch circuit as the AC ballast.

1. Disconnect AC power from the ﬁxture. Remove the

ballast channel cover and install the emergency ballast

in the ballast channel (see Illustration 1).

2. Select the appropriate wiring diagram to connect

the emergency ballast to the AC ballast and lamp.

Make sure all connections are in accordance with the

National Electrical Code and any local regulations.

3. Refer to Illustration 2 and install the test switch through

the ballast channel cover of a troffer or through the side

of a strip ﬁxture. Drill a 1/2" hole and install the switch

as shown. Wire the test switch so that it removes AC

power from both the emergency ballast and the AC

ballast at the same time (see wiring diagrams section of

these instructions).

4. Refer to Illustration 3A or 3B and install the charging

indicator light so that it will be visible after the ﬁxture is

installed.

5. In a readily visible location, attach the label

“CAUTION– This Unit Has More Than One Power

Connection Point. To Reduce The Risk Of Electric

Shock, Disconnect Both The Branch Circuit-Breakers

Or Fuses And Emergency Power Supplies Before

Servicing.”

6. After installation is complete, supply AC power to the

emergency ballast and join the inverter connector.

7. A short-term discharge test may be conducted after

the emergency ballast has been charging for one hour.

Charge for 24 hours before conducting a long-term

discharge test. Refer to OPERATION.

NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label. If a

detached charging indicator light is used, connect by matching wire colors and install as shown on the

installation insert page.

WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW OUTPUT

LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT jOIN

INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED

TO THE EMERGENCY BALLAST.

ILLUSTRATION 3B

STEP 2

ILLUSTRATION 3A

ILLUSTRATION 1

ILLUSTRATION 2

STEP 1

Fixture

Test Button

Hex Nut

Test Switch

Leads

Push to Test

Charging

Indicator

Light

1/2" White

Bushing

Violet (+)

Brown (–)

Violet (+)

Brown (–)

1/2" White

Bushing

5/8" Black

Bushing

5/8" Black

Bushing

1/2" Punch

Fixture Fixture

Charging

Indicator

Light

OPERATION

With AC power applied, the charging indicator light is illuminated, indicating that the battery is being charged.

When power fails, the emergency ballast automatically switches to emergency power, operating one lamp at

reduced illumination. When AC power is restored, the emergency ballast returns to the charging mode and delays

AC ballast operation for ﬁve seconds to prevent false-tripping of AC ballast (end-of-lamp-life) shutdown circuits.This

emergency ballast will operate 14 W through 55 W lamps for a minimum of 90 minutes.

MAINTENANCE

Although no routine maintenance is required to keep the emergency ballast functional, it should be checked

periodically to ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated.

2. Test the emergency operation of the ﬁxture at 30-day intervals for a minimum of 30 seconds. One lamp

should operate at reduced illumination.

3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced illumination for at

least 90 minutes.

REFER ANY SERVICING INDICATED BY THESE CHECkS TO QUALIFIED PERSONNEL.

LAMP

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

1 LAMP

RAPID

START

BALLAST

RED

BLUE

BLUE RED

WHT

BLK

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

LAMP

RED

YEL/BLK

YELLOW

BLUE

1 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLUE RED

BLU/WHT

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

)

(EMERGENCY

LAMP 1

LAMP 2

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

RAPID

START

BALLAST

RED

BLUE

WHT

BLK

RED

BLUE

YELLOW

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

)

(EMERGENCY

LAMP 1

RED

YEL/BLK

YELLOW

BLUE

2 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLUE

RED

BLU/WHT

LAMP 2

BLUE

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

FIG 119 ONE (1) LAMP INSTANT START BALLAST

FIG 99 ONE (1) LAMP RAPID START BALLAST

FIG 100 TWO (2) LAMP RAPID START BALLAST FIG 104 TWO (2) LAMP INSTANT START BALLAST

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION

LAMP 2

LAMP 1

( )

EMERGENCY

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

RAPID

START

BALLAST

YELLOW

BLUE

WHT

BLK

RED

YELLOW

RED

BLUE

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

LAMP 2

LAMP 1

( )

EMERGENCY

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

INSTANT

START

BALLAST

RED

BLUE

WHT

BLK

BLUE

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

RED

)

(EMERGENCY

LAMP 1

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

3 LAMP

RAPID

START

BALLAST

BLUE

WHT

BLK

YELLOW

BLUE

RED

BLU/WHT

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

)

(EMERGENCY

LAMP 1

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLUE

3 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLUE

RED

BLU/WHT

BLUE

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

)

(EMERGENCY

LAMP 1

LAMP 4

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

4 LAMP

RAPID

START

BALLAST

RED

WHT

BLK

YELLOW

RED

BROWN

BLUE

BLU/WHT

BROWN

BLUE

BLU/WHT

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

)

(EMERGENCY

LAMP 1

LAMP 4

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLUE

4 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLUE

YELLOW

BLU/WHT YELLOW

RED

BLUE

RED

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

)

(EMERGENCY

LAMP 1

LAMP 2

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

RAPID

START

BALLAST

BLUE RED

WHT

BLK

YELLOW

BLUE RED

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

LAMP

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

(CAP)

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

(CAP)

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

CAP

WHITE

CHARGING

INDICATOR

LIGHT

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

COM

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

BLK

CAP

HOT WHT/RED

CONNECTOR

INVERTER

CAP

LAMP

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

RAPID

START

BALLAST

RED

BLU

WHT

BLK

RED

WHITE

VIOLET

BROWN

WHT/BLK

BLK

RED

WHITE

TEST

SWITCH

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

BLACK 120V

ORANGE 277V

(CAP UNUSED LEAD)

COM BLK

WALL SWITCH

FIG 105 THREE (3) LAMP RAPID START BALLAST

FIG 120 FOUR (4) LAMP RAPID START BALLAST

FIG 109 ONE (1) 14 W - 55 W LAMP WITHOUT AC BALLAST

WIRING DIAGRAM for EMERGENCYONLY xtures

FIG 109a ONE (1) 36 W - 55 W LAMP WITHOUT AC BALLAST

FIG 123 FOUR (4) LAMP INSTANT START BALLAST

FIG 106 THREE (3) LAMP INSTANT START BALLAST

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION

FIG 99a TWO (2) LAMP RAPID START BALLAST - SERIES YELLOW

FIG 107 TWO (2) LAMP RAPID START BALLAST

FOR 4-PIN LONG COMPACT

FIG 107A TWO (2) LAMP INSTANT START BALLAST

FOR 4-PIN LONG COMPACT

FIG 99b TWO (2) LAMP PROGRAM RAPID START OSRAM BALLAST

Inhaltsverzeichnis

Andere Hubbell Beleuchtungsausrüstung Handbücher

Hubbell

Hubbell KIM LIGHTING VRB1 Bedienungsanleitung

Hubbell

Hubbell Laredo LMC Bedienungsanleitung

Hubbell

Hubbell ExpressLine Miniliter IV MHSY Series Bedienungsanleitung

Hubbell

Hubbell PRS Bedienungsanleitung

Hubbell

Hubbell KILLARK VSQ Series Betriebsanleitung

Hubbell

Hubbell Dual Lite CVEC15 Bedienungsanleitung

Hubbell

Hubbell LITEFRAME LC4 Bedienungsanleitung

Hubbell

Hubbell Compass CU2SO Bedienungsanleitung

Hubbell

Hubbell Litecontrol 22L Series Bedienungsanleitung

Hubbell

Hubbell Laredo LMC Bedienungsanleitung

Hubbell

Hubbell DUAL LITE PG Series Bedienungsanleitung

Hubbell

Hubbell ALFW-6LU-5KBZ Series Bedienungsanleitung

Hubbell

Hubbell Dual-Lite EVHC-BC Series Handbuch

Hubbell

Hubbell Dual-Lite DYNC C1D2 Series Bedienungsanleitung

Hubbell

Hubbell VSLT-UP Bedienungsanleitung

Hubbell

Hubbell KIM LIGHTING LIGHTVAULT LTV55 Bedienungsanleitung

Hubbell

Hubbell KILLARK VEB Series Bedienungsanleitung

Hubbell

Hubbell homeSELECT RMS100 Bedienungsanleitung

Hubbell

Hubbell Prescolite LBSLEDA Bedienungsanleitung

Hubbell

Hubbell DUAL LITE N4X4 Bedienungsanleitung

Hubbell

Hubbell NXP2 Series Bedienungsanleitung

Hubbell

Hubbell WPH Series Bedienungsanleitung

Hubbell

Hubbell DUAL LITE LN4X Series Betriebsanleitung

Hubbell

Hubbell Dual Lite EV Series Handbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung