Hubbell KILLARK VEB Series Bedienungsanleitung

Page 1 of 4

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00912293 FORM NO. K1207 Released 05/01

INSTALLATION, OPERATION &

MAINTENANCE DATA SHEET

(VEB/DEB/VEQ SERIES FLUORESCENT

EMERGENCY LIGHTING FIXTURES)

VEB/DEB/VEQ SERIES FLUORESCENT

EMERGENCY LIGHTING FIXTURES

CAUTION:

Before installing, make sure you are compliant with area classications, failure to do so may result in bodily injury,

death and property damage. Do not attempt installation until you are familiar with the following procedures. All

installation must comply with the applicable Electrical Code.

Make sure that the circuit is de-energized before starting installation or maintenance.

Verify that the installation is grounded. Failure to ground will create electrical shock hazards, which can cause

serious injury and or death.

Technical information, advice and recommendations contained in these documents is based upon information

that Killark believes to be reliable. All the information and advice contained in these documents is intended for

use only by persons having been trained and possessing the requisite skill and know-how and to be used by

such persons only at their own discretion and risk. The nature of these instructions is informative only and does

not cover all of the details, variations or combinations in which this equipment may be used, its storage, delivery,

installation, check out, safe operation and maintenance. Since conditions of use of the product are outside of the

care, custody and control of Killark, the purchaser should determine the suitability of the product for his intended

use, and assumes all risk and liability whatsoever in connection therewith.

Page 2 of 4

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00912293 FORM NO. K1207 Released 05/01

1. IMPORTANT SAFEGUARDS -

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

NOTE: Read this sheet carefully before beginning

installation.

• Do not use this equipment for other than

the intend use as specied on equipment

nameplate. Turn off the supplying circuit before

beginning installation, or performing any

maintenance including revamping.

• Do not install near gas or electric heaters.

• Do not attempt to service battery. The

emergency ballast contains a sealed, no-

maintenance battery. Contact manufacturer for

information on replacements.

• Batteries must be recycled or disposed of

properly.

• Servicing should be performed by qualied

service personnel.

• Do not use this equipment for other than

intended use.

• The use of accessory equipment not

recommended by the manufacturer man cause

an unsafe condition.

• Equipment should be mounted in locations and

at heights were it will not readily be subjected

to tampering by unauthorized personnel.

• The emergency ballast is for use with bi or

quad pin uorescent lamps only.

2. INSTALLATION

CAUTION: To prevent high voltage on red

& yellow output leads prior to installation,

inverter connector must be open. Join inverter

connector after installation, then turn power

ON.

To reduce the risk of electrical shock,

disconnect the AC input and inverter before

servicing.

The emergency ballast must be connected to

an unswitched power source (120/277 V).

NOTE: All installations must comply with the

applicable local and/or National Electrical

Code.

IMPORTANT: Before installing, check the

xture nameplate to be sure you have the

correct xture. Verify ground continuity in the

electrical system.

Refer to nameplate for specic ambient and

supply wire temperature rating.

Page 3 of 4

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00912293 FORM NO. K1207 Released 05/01

1. Install splice box per Instruction Sheet K0451

supplied with the product.

2. Refer to Fig.1 for general guidance. Hang the

xture on the splice box hinge.

3. Attach the green (ground) lead to the splice

box ground screw (provided).

4. For VEB/DEB Series connect the supply

common lead to marked “COM” & supply

line voltage hot lead (120 or 277) to marked

“LINE” at the terminal block. For VEQ series

connect the supply common lead to marked

“COM” & supply line voltage hot lead to

marked “LINE” at the terminal block.

5. Mount the lamps on socket supplied with the

xture.

6. Join the emergency ballast(s) inverter

connector(s) as shown in Fig.2.

7. Close the ballast tank against the splice box

and tighten the screw to secure it.

8. Install globe or refractor in the globe thread.

Hand tighten.

9. Install globe guard (if required) over lugs on

ballast tank, turn until stopped. Secure with

screw.

10. To install reectors, back out (4) screws

provided in ballast tank boxes enough to

slip the reector over the screws and twist in

place. Tighten screws to secure reector.

11. Turn ON the supply circuit to operate the

xture.

NOTE: For push to test station installation

use Killark control station catalog number

FXCS_5B2 (e/push to test nameplate) or

equivalent. Refer to Fig.3 for typical wiring

diagram.

FIG.2

FIG.3

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

P/N 00912293 FORM NO. K1207 Released 05/01 Page 4 of 4

2. OPERATION:

When AC power is applied, the charging

indicator light is illuminated, indicating that the

batter is being charged. When power fails, the

emergency ballast automatically provides at

least 90 minutes of emergency lighting.

3. MAINTENANCE:

As routine maintenance, this emergency

xture should be checked periodically to

ensure proper operation, The following

schedule is recommended.

1. Visually inspect the charging indicator light

monthly. It must be illuminated.

2. Test operation of the circuit at 30 day intervals

for a minimum of 30 seconds. The lamp

should operate.

3. Conduct a 90 minute discharge test once a

year. The lamp should operate for 90 minutes.

SAVE THESE INSTRUCTION SHEETS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hubbell Beleuchtungsausrüstung Handbücher

Hubbell

Hubbell DUAL LITE PG Series Bedienungsanleitung

Hubbell

Hubbell PRS Bedienungsanleitung

Hubbell

Hubbell ALFW-6LU-5KBZ Series Bedienungsanleitung

Hubbell

Hubbell Prescolite LBSLEDA Bedienungsanleitung

Hubbell

Hubbell Dual-Lite EVHC-BC Series Handbuch

Hubbell

Hubbell Dual-Lite DYNC C1D2 Series Bedienungsanleitung

Hubbell

Hubbell KIM LIGHTING LIGHTVAULT LTV55 Bedienungsanleitung

Hubbell

Hubbell NutriLED Series Bedienungsanleitung

Hubbell

Hubbell Kim Lighting Lightvault LTV59 Bedienungsanleitung

Hubbell

Hubbell ExpressLine Miniliter IV MHSY Series Bedienungsanleitung

Hubbell

Hubbell Litecontrol 22L Series Bedienungsanleitung

Hubbell

Hubbell Dual-Lite UFO-LP1 Bedienungsanleitung

Hubbell

Hubbell Dual-Lite EV4D-02WAL Series Handbuch

Hubbell

Hubbell Compass CU2SO Bedienungsanleitung

Hubbell

Hubbell KILLARK VSQ Series Betriebsanleitung

Hubbell

Hubbell Dual Lite CVEC15 Bedienungsanleitung

Hubbell

Hubbell KIM LIGHTING VRB1 Bedienungsanleitung

Hubbell

Hubbell M-7679 R-PAC Bedienungsanleitung

Hubbell

Hubbell VSLT-UP Bedienungsanleitung

Hubbell

Hubbell SAVVANO Bedienungsanleitung

Hubbell

Hubbell Laredo LMC Bedienungsanleitung

Hubbell

Hubbell NXP2 Series Bedienungsanleitung

Hubbell

Hubbell G040 Bedienungsanleitung

Hubbell

Hubbell DUAL LITE EVE Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung