Hunter ACC-1200 Bedienungsanleitung

ACC

Advanced Commercial Controller

Owner’s Manual, Installation, and Programming Instructions for

ACC and ACC Decoder Controllers

■ ACC-1200 12 Station Controller, 42 Station

Capacity, Metal Cabinet

■ ACC-1200-PP 12 Station Controller, 42

Station Capacity, Plastic Pedestal

■ ACC-99D 2-Wire Decoder Controller with

99 Station Capacity, Metal Cabinet

■ ACC-99D-PP 2-Wire Decoder Controller

with 99 Station Capacity, Plastic Pedestal

Table of ConTenTs

ACC INTERFACE AND KEY COMPONENTS 2

WIRING COMPARTMENT INTERIOR 3

METAL CABINET, WALL MOUNT INSTALLATION 4

CONNECTING AC MAIN POWER, WALL MOUNT CABINET 5

METAL CABINET OPTIONAL PEDESTAL INSTALLATION 6

Connecting the Metal Pedestal Main AC Power 6

PLASTIC PEDESTAL INSTALLATION 6

CONCRETE BASE INSTALLATION 7

CONNECTING PLASTIC PEDESTAL AC MAIN POWER 8

120 VAC Connection 8

230 VAC Connection 8

CONNECTING EARTH GROUND (ALL CONFIGURATIONS) 10

INSTALLING STATION MODULES 11

Output Modules (ACM600, AGM600) 11

Connecting the Valve Wires 12

Decoder Output Module (ADM99) 12

Connecting Decoder Output Path Wires 12

KEY CONNECTIONS 13

24 VAC TEST TERMINAL 14

CONNECTING THE MASTER VALVE(S) AND/OR PUMP START RELAY(S) 14

CONNECTING A RAIN OR FREEZE SHUT OFF DEVICE 14

CONNECTING THE HUNTER FLOW SENSOR 15

CONNECTING OTHER FLOW SENSORS 16

ICR REMOTE CONTROL 16

Multiple Stations simultaneously 16

CONNECTING TO IMMS 17

Dial-up telephone (ACC-COM-POTS) 17

Cellular/GSM (ACC-COM-GSM, GSM-E) 18

UHF Radio 18

POWER FAILURES 18

QUICK START 18

CONTROLLER PROGRAMMING AND OPERATION 19

Using the Information Button 19

Setting Current Date and Time 20

Setting Program Start Times 20

To Set Program Start Times 20

Stacked Start Times 20

Overlapping Start Times 20

Multiple Start Times 21

No-Water Window 21

Setting Station Run Time Duration 21

Changing Seasonal Adjust 22

Using the Global Setting 22

Using a Program Specific Setting (set Season Adjust by Program) 22

Timed Delay between Stations 22

Setting Days to Water 22

Set Days to Water 22

Day of the Week Watering 23

Interval Watering 23

Odd/Even Watering 23

Setting Pump and Master Valve Operation 23

Set Pump and Master Valve Operation 24

Changing from Normally Closed to Normally On and Location of P/MV 24

Setting Station Cycle and Soak Durations 24

Set Station Cycle and Soak Durations 24

Cycle and Soak Summary 24

SETTING FLOW MONITORING 25

Step 1: Select The Flow Sensor 25

Step 2: Viewing Real-Time Flow 26

Step 3: Preparing for Flow Learning 27

Step 4: Learning the Flow 27

Step 5: Review And Edit Flow 28

Flow Alarms 28

Alarm Logs 29

Tips on Flow Alarms 30

SETTING CLIK™ SENSOR OPERATION 30

Set Sensor Operation 31

SENSOR ALARMS (CLIK SENSORS SEN 1–4 ONLY) 32

Clear Message 32

Sensor Locations 33

Sensor Locations 35

SETTING PROGRAM OVERLAP OPTIONS 36

Option One: Stack or Overlap 36

Option Two: SmartStack™ 36

Option Three: SSG/SmartStack™ 36

Set Station & Program Names 37

Assign Contact Information 37

DATA HISTORY 38

Name a Program (Up to 12 Characters and Spaces) 38

Name a Station (Up to 12 Characters and Spaces) 38

View Flow Totals 38

View Alarm Logs 38

View Controller Logs 39

View Station Logs 39

Advanced Features 39

View Version and Station Size 40

COMMON ALARM (ATTENTION) MESSAGES 41

Overcurrent 41

Overflow 42

Power Outage/Power Restored 43

Underflow 43

EXTENDED FEATURES 43

Contrast Adjustment 43

No Water Window 44

To set a No Water Window 44

No Water Window rules 44

Delay Between Stations 45

To set a Delay 45

P/MV Style (Normally Closed/Normally On) 45

To change the Normal condition of P/M outputs 46

Setting the Flow Sensor Size and Type 46

Additional settings for OTHER 47

SSG (Simultaneous Station Group) Setup 47

EDIT AN SSG 48

ADDING AN SSG 49

DELETING AN SSG 49

SSG FLOW DATA 49

SSG Rules 49

Custom Manual Program Setup 50

Custom Manual Rules 50

Start a Custom Manual 51

Test Program 51

Run a Test Program 51

Easy Retrieve™ Backup 52

ONE TOUCH MANUAL START 53

MANUAL OPERATION DIAL POSITION 53

SYSTEM OFF 54

RAIN OFF 55

RESET 55

DECODER OPERATIONS (ACC99D VERSIONS) 56

Connecting the 2-Wire Paths 56

Status Lights (ADM-99 Output Module) 57

Decoder Programming 57

Program Decoder Stations 57

Decoder Pump/Master Valves 59

ICD-SEN Sensor Decoder Setup 59

Setup Overview 60

Connect an HFS Meter to an ICD-SEN 60

Connect a Clik Sensor to an ICD-SEN 60

SEN/DEC Setup 60

OTHER SPECIAL DECODER FUNCTIONS (ADVANCED FEATURES) 62

View Decoder Config 62

Display ADM Current 63

Sen/Dec Alarms 63

ACC SOLAR SYNC 64

Preparation 64

Facepack Version 64

Master Module 64

Base Run Times 64

Installation 65

Setup 65

Sensor Test 66

Assign Programs 67

Sensor Shutdown Programming 67

Sensor Mapping 67

Sensor Shutdown by Program 68

Operation & Adjustment 68

Making Adjustments 69

Increase or Decrease Watering 69

Check Run Times 69

Tracking the Adjustment History (Controller Log) 69

Solar-Sync Sensor Alarms 70

S-Sync Comm Failure 71

IMMS-ET AND THE ACC CONTROLLER 72

ET Setup and Operations 72

ET Functions 72

ET Operation 72

ET Sensor Check 73

View ET Sensors 73

ET Alarm Setup 73

EVENT MODE OPTIONS (AGC, SURVEYOR) 75

CENTRAL SOFTWARE AND ACC-AGC COMMUNICATION MODULES 77

Theory of Operation 77

UHF Radio 77

Hardwired Cable 78

COMMUNICATION MODULE INSTALLATION FOR WALL MOUNT CONTROLLER 78

Radio Installation, additional steps 78

Radio Connections, additional steps 79

COMMUNICATION MODULE INSTALLATION FOR PLASTIC PEDESTAL CONTROLLER 79

Radio Installation, additional steps 79

SETUP AND ADDRESSING THE COM MODULE 80

Set the Controller Address 80

Other Com Setup Functions 80

Master Controller 80

Contrast 80

Radio Type 80

Last MR Cmd (Radio Only) 80

DTMF Wait (Radio Only) 80

MR Default Run Time (Radio Only) 81

Modem Type 81

Country Code 81

HWIM 81

Enter Diagnostics 81

Communications Status display [MOD RAD HW] 81

Radio Tone Test 82

Ping Test 82

Ping Hub 82

Soft Reset 82

Total Reset 82

Operating the Com Module 82

TROUBLESHOOTING 83

ACC/AGC LOG MESSAGES 84

Alarm Log messages 84

Alarm Log, Missed Irrigation “Mode” Labels 84

Alarm Log, “Reason” Labels 85

Controller Logs 85

Station Logs 86

SPECIFICATIONS 87

Dimensions 87

Electrical 87

Transformer Input 87

Transformer output 87

Cleaning 87

Features & General Specifications 87

PARTS 88

Wall Mount Controllers (ACC1200, ACC99D) 88

Communication Modules and Parts 88

Pedestal Controllers (ACC1200PP, AGC1200PP, ACC99DPP, AGC99DPP) 89

ACC/AGC Central System Components

(ACC1200, ACC99D, ACC1200PP, AGC1200PP, ACC99DPP, AGC99DPP) 89

INDEX 90

INTRODUCTION

The ACC controller, in its many modular configurations, is Hunter’s premium industrial-grade controller for high-per-

formance irrigation control. Its primary purpose is to operate 24 VAC irrigation solenoids or low-draw solid state relays

for specific durations at specific times. It can also be connected to various sensors, providing automatic shutdown and

notification in case of emergencies, and actual flow records and responses in real time.

With plug-in Com and other modules, the ACC can also communicate with a computerized central control system via

hardwired cable, radio, dial-up telephone, or cellular modem. ACC is also prewired to accept Hunter wireless remote

controls.

• This product should not be used for anything other than what is described in this document.

• This product should only be serviced by trained and authorized personnel.

• This product is designed for continuous outdoor use above sea level to 15,000 feet/4.5 km at temperatures 32–122˚ F.

• These units have an IPX4 rating.

• This controller is not intended for use by young children or infirm persons without supervision; young children

should be supervised to ensure that they do not play with the appliance.

• Hunter Technical Support: 1 (800) 733-2823

1. LCD Display – Backlit, adjustable contrast display

(re-lights when any button is pressed)

2. + Button – Increases flashing value, depending on

function

3. – Button – Decreases flashing value. Most items in

ACC screens “wrap” so that you can continue in either

direction through all the choices

4. Copy/Learn Button – Copies a time or value in a

flashing field, for pasting into similar fields. Also used

to learn typical flow (when a flow sensor has been

installed)

5. Paste/Pause Button – Pastes a copied time or value

into a new field. Also used as Pause/Resume feature

during watering, shuts off devices for 30 minutes or

until resumed

6. Programs Button – Selects one of the automatic

Programs (A-F), starts Test program, allows Reset

(with Reset button)

7. Up and Down Arrow Buttons – Used to move up and

down through adjustable functions in various screens,

and to select higher or lower numbered items

8. Left and Right Buttons – Used to move left and right in

some screens

9. Information Button – Lights display, and provides

instant help and other information, depending on dial

position. Also used to access Extended Features, when

held down while turning to specific dial positions

10. Programming Dial – Used to access all functions of

ACC. The most basic automatic watering can be set up

in the first 4 dial positions

11. Reset Button – Recessed switch erases some or

all memory when combined with pressing specific

buttons

12. Facepack Release Button – Hold down while removing

facepack from inner door panel

13. Door Grip – Convenient finger grip for opening inner

door

14. Logo Badge – Removable for installation of optional

communications modules

aCC InTerfaCe and Key ComponenTs .......................................

2 3 4 5 6

WIrInG ComparTmenT InTerIor ................................................

1. Inner Door – Opens to main wiring compartment

2. AC Wiring compartment – For connection of 120/230V

AC power with 1 x 0.75" (19 mm) conduit opening

3. Fuse – 2 Amp (fast) 250V, 6 x 20 mm

4. Conduit Openings, Low Voltage – 2" x 2½" (64 mm),

2" x ¾" (19 mm)

5. Wire Tie Holders for Valve Wires – Valve wiring area

6. Station Output Terminals (Valve Wires) – screw

terminals on 6-station output modules

7. Upper Deck Panel with Led Status Indicators –

Numbered station lights, green for active, red for faults

8. Sliding Lock for Output Modules – Permits addition

or removal of output modules, locks wired modules

in place

9. Master Module – Includes sensor, Pump/Master

Valve, and other accessory connections

10. SmartPort® – Integrated connector for ICR/SRR

receiver (on side of cabinet)

11. Earth Ground Lug – For connection of earth ground

copper wire (for surge protection only). Do not

connect valve commons – see Master Module for

Common wiring of solenoids and valves.

3 4 5 6

7 89

Explanation of Symbols

Consult Documentation Double Insulated

Hazardous Voltage Present

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hunter Controller Handbücher

Hunter

Hunter Hydrawise Ready Bedienungsanleitung

Hunter

Hunter PRO-C P2C Series Betriebsanleitung

Hunter

Hunter XC hybrid Betriebsanleitung

Hunter

Hunter Eco-Logic 6 Betriebsanleitung

Hunter

Hunter XC Hybrid Betriebsanleitung

Hunter

Hunter Node Bedienungsanleitung

Hunter

Hunter X-CORE Betriebsanleitung

Hunter

Hunter X2-400 Betriebsanleitung

Hunter

Hunter 600-Z Bedienungsanleitung

Hunter

Hunter Hydrawise HC-1200M Montageanleitung

Hunter

Hunter NODE-100 Bedienungsanleitung

Hunter

Hunter SVC-400 Bedienungsanleitung

Hunter

Hunter Hydrawise HC-1200M Bedienungsanleitung

Hunter

Hunter WVC-100 Originalbetriebsanleitung

Hunter

Hunter NODE-100 Betriebsanleitung

Hunter

Hunter X-CORE XC-2 Bedienungsanleitung

Hunter

Hunter ACC2 Installationshandbuch

Hunter

Hunter SRC Plus Bedienungsanleitung

Hunter

Hunter 99373 Bedienungsanleitung

Hunter

Hunter ICC-800PL Betriebsanleitung

Hunter

Hunter Hydrawise HCC-FPUP Bedienungsanleitung

Hunter

Hunter ACC2 Installationshandbuch

Hunter

Hunter Pro-C Betriebsanleitung

Hunter

Hunter ICC2 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch