Hunter Hydrawise HC-1200M Bedienungsanleitung
2
3
3
4
5
6
7
7
8
8
8
8
8
Table of Contents
Table of Contents
HC Hydrawise - Quick Start Guide
HC - Wiring a Master Valve and Setting Up Online
HOW IS IT CONFIGURED?
HC - Wire Distance (Controller to Valve)
HC - Valve Wiring
Solenoid Valve Wiring
Connecting the Transformer
HC - Controller Mounting
CABLE ENTRY
ENTRY FROM THE REAR OF THE CONTROLLER
ENTRY VIA ¾ INCH CONDUIT
MOUNTING THE CONTROLLER
Copyright 2020 Hunter Industries. All Rights Reserved. 2
HC Hydrawise - Quick Start Guide
HC - Wiring a Master Valve and
Setting Up Online
A master valve is an automatic valve that is installed at the point where the irrigation
system connects to the water supply. (Sometimes this circuit is called a “pump start circuit”.
Both types of circuits work identical, and can be used for a pump and/or a master valve.)
The controller turns the master valve on and off.
Zone valves are the individual valves that operate a group of sprinklers or drip emitters.
Hydrawise controllers support 6 - 54 zone valves, depending on the model. Typically one
zone valve is turned on at a time and controls the irrigation in a specific area of your
garden. Whenever one of the irrigation zone valves is told to open by the controller, the
controller also signals the master valve to open. So the master valve is a little like a backup
valve or a fail-safe valve. The purpose of the master valve is to shut off the water to the
Copyright 2020 Hunter Industries. All Rights Reserved. 3
irrigation system when none of the zone valves are operating. The image below shows a
master valve operating connected to Zone 12 on a Hydrawise controller.
Water main
Master valve
Solenoid valves
Water to zones
Common wires
24V AC plug pack
HOW IS IT CONFIGURED?
With a Hydrawise controller, any one of your 6 / 12 zones can be configured to act as a
master valve. The master zone is configured on the Zones & Schedules page above your
Copyright 2020 Hunter Industries. All Rights Reserved. 4
list of irrigation zones. For more information on this setup, please visit support article here
[1].
Initially, there is no master valve configured and all zones on the controller can be used as
normal zone valves. To select a master valve, select the relevant zone from the list next to
the text which says Master valve.
HC - Wire Distance (Controller to
Valve)
Below is a chart indicating the maximum wire runs that can be used when installing
Hunter AC solenoids and valves.
Copyright 2020 Hunter Industries. All Rights Reserved. 5
Valve Wire Sizing (Maximum One-Way Distance in Feet Between Controller and Valve)
Ground
Wire Size Control Wire (ft)
18 AWG /
1.0 mm
16 AWG /
1.2 mm
14 AWG /
1.6 mm
12 AWG /
2.0 mm
10 AWG /
2.5 mm
8 AWG / 3
mm
6 AWG / 4
mm
18 AWG / 1.0
mm 850 1040 1210 1350 1460 1540 1590
16 AWG / 1.2
mm 1040 1340 1650 1920 2150 2330 2440
14 AWG / 1.6
mm 1210 1650 2150 2630 3080 3450 3700
12 AWG / 2.0
mm 1350 1920 2630 3390 4170 4880 5400
10 AWG / 2.5
mm 1460 2150 3080 4170 5400 6670 7690
8 AWG / 3
mm 1540 2330 3450 4880 6670 8700 10530
6 AWG / 4
mm 1590 2440 3700 5400 7690 10530 13330
HC - Valve Wiring
Your controller has either 6 or 12 zones depending on the model you have purchased.
There are 3 COMMON wiring points for convenience – any or all of them can be used.
Refer to the diagram below when connecting your solenoid valves to the controller. Please
click on the link below for the downloadable version of the controller to valve wiring
diagram. Hydrawise Controller Connection Diagram [2]
Copyright 2020 Hunter Industries. All Rights Reserved. 6
Solenoid Valve Wiring
1. Take one wire from each solenoid, twist together and connect to the common (usually
white) wire of your multi-conductor irrigation cable.
2. Connect each of the other individual wires to a different colored wire. Record zones
against wire color for later reference.
3. Connect the common wire from the multi-conductor cable (usually white) to any of the
three terminals on the controller marked COMMON.
4. Connect each of the other solenoid wires to one of the ZONE inputs.
5. If a master valve (sometimes labelled as MV on other controllers) is installed this can
be connected to any spare zone as any of the zones can be assigned as a master
valve output. Configuration of the master valve in the Hydrawise app is required.
6. Click the blue wiring cover into place to seal the controller and protect the wiring.
Connecting the Transformer
1. Use the plug pack supplied and connect the wires to the red AC terminal blocks on the
unit marked as 24V. Polarity of the wiring is not important.
2. Turn the power on. The power indicator will light up.
Copyright 2020 Hunter Industries. All Rights Reserved. 7
HC - Controller Mounting
The HC is designed for indoor installations only. The chosen location must have Wi-Fi
coverage. Wi-Fi coverage can be easily tested using a smart phone with Wi-Fi connectivity
or on the HC itself (signal strength is shown when you select a wireless network).
Note: The HC Controller is an indoor model and is not water-proof or weather resistant,
and must be installed indoors or in a protected area. Do not plug transformer into power
source until controller is mounted and all wiring has been connected.
CABLE ENTRY
The controller has 2 cable entry options -- from the rear of the case or via a conduit from
the bottom of the controller.
ENTRY FROM THE REAR OF THE CONTROLLER
Using a sharp knife, remove the 2 cutouts on the rear of the controller as indicated on the
diagram as .
ENTRY VIA ¾ INCH CONDUIT
Using a sharp knife, cut around the semi-circular line on the controller as indicated on the
diagrams as . Cut around the matching line on the blue controller wiring cover.
MOUNTING THE CONTROLLER
1. Using a drill bit of 3/16 inch diameter, drill a hole to a depth of 1 inch (25 mm).
2. Insert plastic anchor so it is flush with the surface of the wall.
3. Screw 1 inch screw into plastic anchor leaving the head protruding about 1/8 inch (4
mm).
4. Slide the controller case over the screw head.
Copyright 2020 Hunter Industries. All Rights Reserved. 8
5. Mark second mounting point (see in diagram), remove controller, drill hole, insert
plastic anchor, slide controller case over first screw head and screw into place.
Rear cable entry point (remove with knife)
Conduit cable entry point (remove with knife)
Wall mounting screw hole
Power indicator
Expansion module cable entry
Go to previous screen
Go to home screen
STEPS 1-5
Copyright 2020 Hunter Industries. All Rights Reserved. 9
Andere Handbücher für Hydrawise HC-1200M
9
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Hunter Controller Handbücher
Hunter
Hunter SVC-400 Bedienungsanleitung
Hunter
Hunter ACC2 Installationshandbuch
Hunter
Hunter ICC2 Bedienungsanleitung
Hunter
Hunter X-CORE Betriebsanleitung
Hunter
Hunter X-CORE XC-2 Bedienungsanleitung
Hunter
Hunter Hydrawise HC-1200M Bedienungsanleitung
Hunter
Hunter WVC Betriebsanleitung
Hunter
Hunter X-CORE Bedienungsanleitung
Hunter
Hunter Hydrawise HCC-FPUP Bedienungsanleitung
Hunter
Hunter Smart Valve Controller Betriebsanleitung
Hunter
Hunter ACC-1200 Bedienungsanleitung
Hunter
Hunter ICC2 Bedienungsanleitung
Hunter
Hunter X-Core XC-801i-E Betriebsanleitung
Hunter
Hunter 27178 Bedienungsanleitung
Hunter
Hunter Hydrawise Pro-HC Kurzanleitung
Hunter
Hunter Node Bedienungsanleitung
Hunter
Hunter 99111 Bedienungsanleitung
Hunter
Hunter PRO-C PC Series Betriebsanleitung
Hunter
Hunter ICC2 Bedienungsanleitung
Hunter
Hunter SpectraProbe XE Gebrauchsanweisung
