Hunter 44300 Bedienungsanleitung

OwnerÕs Manual

SINCE 1 8 8 6

44300/44350

Other Quality Products from Hunter

Fans

HumidifiersAir Purifiers

We are pleased you have selected one of our broad line of home comfort products. Our

products are manufactured to high quality standards and are designed for years of service.

We hope you will be satisfied and thank you for buying a Hunter product.

Table Of Contents

Installation

Operation

Features 6

Remove Old Thermostat 8

Labeling Wires 10

System Selector Switches 14

Connecting Wires and Mounting Thermostat 14

Programming/Setting Clock 16

Personal Program Schedule 20

Reviewing Program Settings 26

Manual Overide 27

Temperature Span 30

Backlighting 30

Filter Monitor 31

Trouble Shooting Guide 32

Typical Wiring Diagrams 34

Read This Before Installing Thermostat

IMPORTANT

Read the entire installation section of this

Owner’s Manual thoroughly before you begin

to install or operate your Hunter Thermostat.

• Remove the mylar label from the display

window.

INSTALLATION

All installation is normally performed at your

thermostat.

PROGRAMMING

You can practice programming before

installing your thermostat by inserting and

connecting the batteries and following the

instructions on page 14. This can be done while

you relax in your favorite chair and is a very

good way to familiarize yourself with all the

functions of your Hunter Thermostat.

OPERATION

Your Hunter Thermostat is designed to

operate with most gas, oil, electric or 2-wire

hot water heating, and air conditioning systems

that have 24-volt or millivolt control.

This Hunter Thermostat will not control multi-

stage heating or cooling systems, 110/220 V

systems, or 3 wire zone systems.

COMPRESSOR PROTECTION

The thermostat provides a 4-minute delay

after shutting off the compressor before it

can be restarted. This feature will prevent

damage to your air conditioner compressor

caused by rapid cycling. It does not provide a

delay when there are power outages.

TEMPERATURE RANGE

Your thermostat can be programmed between

40°F and 95°F (5°C and 35°C). However, it will

display room temperatures from 32°F to 99°F (0°C

and 37°C).

POWER FAILURE

Whenever the main power is interrupted or

fails, the battery power retains the programs

and current time.

This thermostat is designed to optimize the use of your heating and cooling equipment. It

does this by matching your comfort (the temperatures in your home) to your schedule.

An example:

6:00 am – You wake up. Program 1 has the heat set to 70° (21°C).

7:30 am – You leave for work. The second program turns the heat back to 62° (17°C)

while you are away.

5:00 pm – You come home. The third program has already warmed your house back

to 70° (21°C).

10:00 pm – You go to bed. A half hour later, program 4 turns the heat back to 64° (18°C)

to save energy while you are under the blankets.

How This Thermostat Works…And Saves You Money

BATTERY WARNING

When the batteries are low, the “LOW BATT”

indicator on the display will flash. When this

happens, install new batteries immediately.

Once the “LOW BATT” indicator appears, the

thermostat will continue to operate for

approximately 30 days. (Only alkaline batteries

should be used in your thermostat.

Rechargeable batteries have different properties

which may cause the thermostat to not operate

properly. Do not use old batteries.) The batteries

should last one year.

CAUTION: The batteries are the only source

of power used to operate your system. If you

do not replace the batteries, the display will

dim and your heating and cooling system will

stop operation.

NOTE: If you plan to be away from the

premises over 30 days, we recommend that

you replace the old batteries with new

alkaline batteries prior to leaving.

LIGHT

6-7

Features

Manual switch for

turning on heating and

cooling system.

Display backlight for viewing in the dark.

(Feature found only on certain models.)

Manual switch for

automatic or continuous

fan operation.

Battery door for easy access

Soft touch programming

buttons (see below)

Display shows time, day, temperature, program number,

hold, usage and low battery indicator.

Reset button for

resetting computer back

to 12:00 A.M. and

clearing all programs.

Individual

pushbuttons for

raising or lowering

temperature settings.

M T W TH F SA SU

SET TEMP HOLD TEMP

88:88 88

HEAT COOL

1234

FILTER LO BAT

Changes the clock

into 12 or 24 hour

(military) mode.

(Model 44300)

HOLD/CLEAR button.

(Model 44350)

For entering minute of day.

For reviewing

and changing

weekday or

weekend

programs

Picks the

day/days for

programs Returns

display to

current

time and

temperature.

Automatically

programs

thermostat for

weekday and

weekend

program

settings.

For entering day of week.

Reviews filter

usage in

hours and

minutes. Also

resets filter

counter to

zero.

For entering hour

of day.

MIN

AUTO

PROGRAM

HOUR

PROG

DAY

FILTER

12/24 HRS

PROG

DAY RETURN

This thermostat comes with two #8 slotted screws and two wall anchors for mounting. To

install your unit, you should have the following tools and materials.

■Slotted screwdriver ■Electric drill and 3/16" bit

■Hammer ■Two 1.5V (AA) Size Alkaline batteries

CAUTION: Do not remove any wiring from existing thermostat before reading the

instructions carefully. Wires must be labeled prior to removal.

■IMPORTANT! Turn off the power to the furnace at the main power panel or at the furnace.

■Remove existing thermostat cover and thermostat. See Figure 1. Some thermostats will have

screws or other locking devices that must first be removed. Once wall mounting plate is

exposed, look for wires.

■If wires are not visible, they may be connected to the back of the wallplate. Again, look for

screws, tabs, etc. Some models have doors that open to expose wires and mounting screws.

(See Figure 1).

8-9

Installation

What You Need

Remove Old Thermostat

TYPICAL HOME THERMOSTATS

FIGURE 1

Wall Mounting Plate Thermostat Cover

■Each wire coming from the wall to the existing thermostat is connected to a terminal point on

that thermostat. Each of these terminal points is usually marked with a code letter as shown in

Table A on page 11.

■The number of wires in your system can be as few as two (for heat only systems), as many as

eight, or any number in between. If you follow the labeling procedures correctly, you do not

have to be concerned about how many wires there are.

■There is often no terminal marking on the existing thermostat of two wire, heat only systems.

Do not worry, just connect either of the wires to the RH terminal, then connect the other wire

to the W terminal to complete the circuit.

■IMPORTANT! BEFORE DISCONNECTING ANY WIRES, APPLY THE SELF-ADHESIVE LABELS

PROVIDED TO THE WIRE AS SHOWN IN TABLE A ON PAGE 11. (For example, attach the

label marked W to the wire which goes to the W or H terminal on your existing thermostat.)

IGNORE THE COLOR OF THE WIRES since these do not always comply with the standard.

■After labeling wires, disconnect them from the existing

thermostat terminals.

■Remove existing wallplate. To make sure wires do not fall

back into wall opening, you may want to tape them to the

wall.

■If hole in wall is larger than necessary for wires, seal this hole

so that no hot or cold air can enter the back of the

thermostat from the wall. This air could cause a false

thermostat reading.

10-11

Installation

Label Wires

WGYRH

Andere Handbücher für 44300

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hunter Thermostat Handbücher

Hunter

Hunter 44155C Bedienungsanleitung

Hunter

Hunter 44033-01 44272 Bedienungsanleitung

Hunter

Hunter HUNTER 42203 Bedienungsanleitung

Hunter

Hunter 44660 Benutzerhandbuch

Hunter

Hunter 44660 Bedienungsanleitung

Hunter

Hunter 44459 Bedienungsanleitung

Hunter

Hunter Auto Temp Plus 44422 Bedienungsanleitung

Hunter

Hunter 42711-01 Bedienungsanleitung

Hunter

Hunter 44905 Bedienungsanleitung

Hunter

Hunter 44155C Bedienungsanleitung

Hunter

Hunter 44272 Montageanleitung

Hunter

Hunter Set & Save 47350A Bedienungsanleitung

Hunter

Hunter 42177 Bedienungsanleitung

Hunter

Hunter 43860 Bedienungsanleitung

Hunter

Hunter Set & Save 47110A Bedienungsanleitung

Hunter

Hunter 144860 Bedienungsanleitung

Hunter

Hunter 44008-01 Bedienungsanleitung

Hunter

Hunter Set & Save 47300A Bedienungsanleitung

Hunter

Hunter 42177 Benutzerhandbuch

Hunter

Hunter 44110 Bedienungsanleitung

Hunter

Hunter 44100B Bedienungsanleitung

Hunter

Hunter 44372 Bedienungsanleitung

Hunter

Hunter 40080 Bedienungsanleitung

Hunter

Hunter 40135 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung