Hunter 44760 Bedienungsanleitung

Owner’s Manual Model 44760

Auto Temp Heat Pump Thermostat

41652_model44760_web.pmd

Introduction

CONGRATULATIONS!

Your new Hunter electronic thermostat will provide years of

reliable service. By saving energy, your thermostat will pay for

itself during its first season of use. Thank you for buying a

Hunter product!

Please read this manual for complete instructions on installing

and operating your thermostat.

If you require further assistance, call Hunter Support at 888-

830-1326 from 8 AM to 5 PM Central Time.

Model Information:

Model Number ___________________________________________

Serial Number____________________________________________

Date Purchased __________________________________________

Where Purchased _________________________________________

44760

41652_model44760_web.pmd

(continued)

Table of Contents

PROGRAMMING

INTRODUCTION

INSTALLATION

Read This Before Installing Thermostat 6

Features 8

What You Need 10

Remove Old Thermostat 10

Wire Labeling 11

Mount Wallplate and Thermostat 14

Connect Wires and Mount Thermostat to Wallplate 15

Option Menu 16

Setting Time and Day 18

12 Hr. / 24 Hr. Time Format 19

Programming Introduction 20

Personal Program Schedule 21

Programming 23

Weekday/Weekend Programming 24

7-Day Programming 26

Everyday Programming 28

Table of Contents (continued)

PROGRAMMING

(continued)

OPERATIONS

Program Options 30

Programmable Fan 30

Reviewing Programs 30

Power Switch 32

System Selection Key 32

Fan Key 33

System Indicator Light 34

Emergency Heat 35

Reviewing the Current Temperature Setting 35

Temporary Manual Override 36

Permanent Manual Override 37

Vacation (Programmable) Hold 38

Auto Season Changeover 39

Home Today 40

Energy Monitor 42

Filter Monitor 43

SPAN Settings 44

41652_model44760_web.pmd

TROUBLESHOOTING

OPERATIONS

(continued)

SAFETY FEATURES

Auto Recovery 45

Keyboard Lock 46

Backlighting

(INDIGLO®Night-Light)

AC Power Monitor 48

Low Battery Warning 48

Error Mode 49

Problems & Solution 50

Technical Support 51

Heat Pump Systems 52

WIRING DIAGRAM

Read This Before Installing Thermostat

IMPORTANT

1Read the entire installation section of this Owner’s Manual

thoroughly before you begin to install or operate your

Hunter Thermostat.

Remove the Mylar label from the LCD display window.

INSTALLATION

2All installation is normally performed at your

thermostat.

ARMCHAIR PROGRAMMING

3You can program your thermostat before installation by in-

serting the batteries and following the instructions starting

on page 16. This can be done while you relax in your favorite

chair and is a very good way to familiarize yourself with all the

functions of your Hunter Thermostat.

SYSTEM COMPATIBILITY

4Your Thermostat is designed to operate these

24-Volt systems:

■Multi-stage heat pumps with auxiliary heat

■Single-stage heat pumps

This thermostat will not control 120/240 Volt systems or

millivolt systems.

COMPRESSOR PROTECTION

5The thermostat provides a 3.5 minute delay after shutting off

the heating or cooling system before it can be restarted.

This feature will prevent damage to your compressor caused

by rapid cycling.

41652_model44760_web.pmd

TEMPERATURE RANGE

6Your thermostat can be programmed between 45°F and 95°F

(7°C and 35°C). However, it will display room temperatures

from 15°F to 99°F (-9°C and 37°C). “HI” will be displayed if the

temperature is higher than 99°F (37°C), and “LO” will be dis-

played if the temperature is lower than 15°F (-9°C).

AUTO RECOVERY

7Your thermostat is set from the factory to gradually recover

the room temperature from an energy saving program to

your comfort program. Therefore, the thermostat may turn your

system on several minutes prior to your programmed time. This

operation is normal, but can be turned off. Refer to the Options

Menu information on pages 16.

OPERATION

8This system operates on your system’s 24 Volt power supply.

The supply is monitored by the thermostat, and it will stop

functioning if AC power is lost. (When using backup batteries,

“No AC Pwr” will be displayed.) All system controls will remain

off until power is restored.

NOTE:

The INDIGLO®Night-Light will not function when

AC power is lost.

BATTERY WARNING

9Fresh alkaline batteries will provide over one year of memory

backup and clock operation. However, when the batteries

become drained, a low battery warning will appear on the dis-

play. When this message occurs, install 2 new AAA batteries. You

have approximately 30 seconds when changing the batteries to

keep thermostat’s clock and program settings.

NOTE:

The default system selection at power-on is HEAT.

Batteries are recommended to prevent an undesired sys-

tem change due to a power outage.

Features

INDIGLO®Night-Light

activated by pressing any key.

Energy Monitor:

Measures and displays

heating and cooling

system operating time for

Today, Yesterday, This

Month, Last Month, or

Total. By monitoring your

energy usage, you can

program the thermostat

to optimize energy

savings.

Home Today: Overrides energy-saving program

temperatures while you are at home for the day.

Alpha-numeric display shows time, day, temperature,

program number, and other feature information as required.

Power Switch:

Select ON, Positive

OFF, or Emergency

Heat.

Soft-touch

programming

keypad, see details

below.

Temperature Keys:

Keys for raising or

lowering temperature

settings.

Reset: Press with a

paper clip to reset the

thermostat and return

to power-up settings.

41652_model44760_web.pmd

Fan Key: Used to select fan mode.

Select Auto, ON, or Program

Controlled.

System Indicator LEDs: Show status

of Stage 1, Emergency, Stage 2, and

Check System.

System Key: Use to select system.

Select Heat, Cool or Auto.

Day/Time Key: Used for entering

the Clock setting mode. Use with

the Up and Down keys to set the

time and day.

Filter: Displays the filter usage

counter in hours and minutes.

Vacation / Hold: Enters permanent and vacation

(Programmable) HOLD modes.

Return-Clear Key: Returns to

normal display mode.Also clears

Filter and Energy counters, and

HOLD modes.

Program-Day Key: Selects the day

or days to review or change in

Program Mode.

Option Key: Enters the option

menu.

Program Key: Enters Program

Mode for reviewing or chaning

Weekday, Weekend, Daily or

Everyday programs.

As an ENERGY STAR®Partner,Hunter Fan Company has determined that this programmable

thermostat meets the ENERGY STAR®guidelines for energy efficiency.

INSTALLATION

Wall Mounting Plate Thermostat Cover

What You Need

This thermostat includes two #8 slotted screws and two wall an-

chors for mounting. To install your thermostat, you should have

the following tools and materials.

■

Slotted Screwdriver(s)

■

Electric drill and 3/16" bit

■

Phillips Screwdriver

■

Two 1.5 V (AA) size alkaline batteries

■

Hammer

CAUTION:

Do not remove any wiring from existing ther-

mostat before reading the instructions carefully. WIRES

MUST BE LABELED PRIOR TO REMOVAL.

■

IMPORTANT! Turn off the power to the furnace at the main

power panel or at the furnace.

■

Remove existing thermostat cover. See Figure 1. Some ther-

mostats will have screws or other locking devices that must

first be removed. Once wall mounting plate is exposed, look

for wires.

If wires are not visible, they may be connected to the back of

the wallplate.Again, look for screws, tabs, etc. Some models

have doors that open to expose wires and mounting screws.

(See Figure 1).

Remove Old Thermostat

TYPICAL HOME THERMOSTATS

Figure 1

41652_model44760_web.pmd

(continued)

Wire Labeling

■

Each wire coming from the wall to the existing thermostat is

connected to a terminal point on that thermostat. Each of

these terminal points is usually marked with a code letter as

shown in Table A on the next page.

■

The number of wires in your system can be as few as four

(for single-stage systems), as many as eight, or any number

in between. If you follow the labeling procedures correctly,

you do not have to be concerned about how many wires

there are.

■

IMPORTANT! BEFORE DISCONNECTING ANY WIRES,APPLY

THE SELF-ADHESIVE LABELS PROVIDED TO THE WIRE AS

SHOWN IN TABLE A and B ON PAGES 12-13. (For example,

attach the label marked W to the wire that goes to the W or H

terminal on your existing thermostat.) IGNORE THE COLOR OF

THE WIRES since these do not always comply with the standard.

■

After labeling wires, disconnect them from the existing ther-

mostat terminals.

■

Remove existing wallplate.To make sure wires do not fall back

into wall opening, you may want to tape them to the wall.

■

If hole in wall is larger than necessary for wires, seal this hole

so that no hot or cold air can enter the back of the thermostat

from the wall.This air could cause a false thermostat reading.

INSTALLATION

TERMINAL FUNCTION

LABELS (HEAT PUMP) COMMENTS

R24V AC supply Hot wire of 24VAC transformer. Powers the thermostat & system.

Y1 Compressor stage 1 Activates the 1st stage compressor. (Heat or Cool for Heat Pumps)

W2 Auxiliary heating Activates the 2nd stage (auxiliary) heating when required.

EEmergency heating

Activates Emergency heating ONLY when the System Switch is in Emergency (em) Mode.

OReversing valve Activates reversing valve in COOL mode. ALWAYS ON in COOL MODE.

(cooling mode)

BReversing valve Activates reversing valve in HEAT mode. ALWAYS ON in HEAT MODE.

(heating mode)

GFan Activates the system Fan. (Can be Auto, On, or Program controlled)

LSystem monitor Activates System Check LED on the front of thermostat.

(Controlled by the system, not the thermostat.)

C24V AC common Common wire of 24V AC transformer. REQUIRED for thermostat operation.

TABLE A – TERMINAL DESCRIPTIONS

41652_model44760_web.pmd

TABLE B

HEAT PUMP CROSS-REFERENCE CHART

NOTE:

If your heat pump thermostat does not have an E wire, use the provided jumper wire to connect the E terminal to

the W2 terminal, as shown in three examples above. Refer to the Wiring Diagram on page 52.

EXAMPLES OF DIFFERENT SYSTEM TERMINALS

HUNTER BRYANT, RHEEM- TRANE,

TERMINALS CARRIER COLEMAN COMFORTMAKER PAYNE RUUD WEATHERTRON YORK LENNOX (1) LENNOX (2)

RRR R RRRRRV-VR

Y1 Y or Y1 Y Y Y Y Y Y Y M

W2 W2 W2 W1 W2 W2 W W W1 Y

EEEjumper E E X2 jumper E E

to W2 to W2

OOOOOOOR

BBB

GGG G GGGGGF

LL or F L L or X L L X L

CCXC, X, X1 C, C1, X1 X B B C X

Note: W2 wires Note: T wire

no connection no connection

INSTALLATION

Mount Wallplate and Thermostat

■

Remove the wallplate from your thermostat by pressing the

release tab on the bottom of the thermostat. (See Figure 2.)

■

Position wallplate on wall and pull existing wires through

large opening. Then level for appearance. Mark holes for plas-

tic anchors provided if your existing holes do not line up with

those on the Hunter wallplate.

■

Drill holes with 3/16" bit and gently tap anchors into the

holes until flush with wall.

■

Reposition wallplate to wall, pulling wires through large

opening. Insert mounting screws provided into wall anchor

and tighten. (See Figure 3.)

Figure 2 Figure 3

41652_model44760_web.pmd

Connect Wires and Mount Thermostat to Wallplate

■

Straighten bare end of each wire and cut or strip it to 1/4”

maximum. Insert each labeled wire into the bottom of the

maching terminal. Refer to figures 4 and 5.

■

Hold the wires in each terminal and tighten the terminal

screws securely, otherwise a loose wire could cause opera-

tional problems with your system or thermostat.

■

Push excess wire back into hole to prevent interference with

mounting of the thermostat.

■

Make sure the Power Switch is set to OFF.

■

Insert two AAA size alkaline batteries, observing the polarity

marked on the unit.

■

Insert the upper tabs on the thermostat body into the slot at

the top of the wallplate. Press bottom of the thermostat body

to snap it into the wallplate. (NOTE:

Do not force the ther-

mostat onto the wallplate, as the terminal pins may be

damaged. If it does not snap properly, the thermostat

may not work.

)

■

Switch on the main power at the panel or furnace.

Figure 4

Figure 5

RY1

Insert

G C L O W2 B E R Y1

PROGRAMMING

Option Menu

Your thermostat has many settings that can be adjusted to fit your system and preferences.

■

Press to enter the Option Menu and to change to the next option selection.

■

Press at any time to return to normal mode.

Fahrenheit or Celsius (F°/C°) selection

■or to change the thermostat display between

Fahrenheit and Celsius.

12 Hr or 24 Hr. Clock selection

■or to change the time format display between

12 hour (AM / PM) and 24 hour (military).

option

ret-clear

option

Temp

Clock

41652_model44760_web.pmd

Stage 1 SPAN selection

■or to change the SPAN setting to 1, 2, or 3.The

factory setting is 2. Setting 1 will cause shorter cycle times. Setting 3

will cause longer cycle times.

Auto Recovery selection

■or to enable “YES” or disable “NO” the Auto

Recovery Mode.The factory setting is “YES.”

■To change between Heat or Cool recovery modes.

NOTE:

Auto Recovery is one of the ENERGY STAR®features of this thermostat. Refer to the Auto Recovery section on

pages 45-46 for more information.

LCD Contrast adjustment

■or to change the LCD contrast between 0 and 9.

Lower numbers lighten the display. Higher numbers darken the display.

The factory setting is 5.

option

Span Stg1

system

option

Recovery

System

option

LCD

PROGRAMMING

Setting Time and Day

■The LCD will show this information when batteries are first installed, or after

the Reset button is pressed.The temperature will update after a few seconds.

■During time and day setting mode, the temperature and program

displays will go blank.

■Example: Set the Thermostat to the current time of 2:16 PM on Saturday.

Refer to the Steps below.

Step 1 ■Press to enter time and day setting mode. The current hour and the

AM / PM indicator will be flashing.

■Press to change the Hour up or down to the current hour.

Note the AM / PM indicator, as the display will change at 12 AM

and 12 PM.

Step 2 ■Press again to change from hour setting to minute setting.The current

minute will be flashing.

■Press to change the Minute up or down to the current minute.

Monday

System

Fan

Tem p

day-time

Monday

day-time

Monday

41652_model44760_web.pmd

Step 3 ■Press again to change from minute setting to day setting.The current

day will be flashing.

■Press to change the Day up or down to the current day.

Step 4 ■Press again to change back to the normal display.

NOTE:

You may press

ret-clear

at any time during Day and Time setting to return to the normal display.

Saturday

day-time

ret-clear

Saturday

System

Fan

Tem p

12 Hr. / 24 Hr. Time Format

Your thermostat is set from the factory in normal 12

(AM / PM) time format. To change to 24 hour (military)

time, press

option

at any time while the Hour, Minute,

or Day is flashing to toggle between the 12 hour and 24 hour

formats. The AM / PM indicator will not be displayed in 24

hour mode. Both the current time and all programs will auto-

matically change to the selected format. The time format may

also be changed in the Option Menu.

Inhaltsverzeichnis

Andere Hunter Thermostat Handbücher

Hunter

Hunter 44110 Bedienungsanleitung

Hunter

Hunter 42345 Bedienungsanleitung

Hunter

Hunter 43860 Bedienungsanleitung

Hunter

Hunter 42122 Montageanleitung

Hunter

Hunter 42711-01 Bedienungsanleitung

Hunter

Hunter 44377 Benutzerhandbuch

Hunter

Hunter Energy Monitor AC 42205 Bedienungsanleitung

Hunter

Hunter Energy Monitor AC 42205 Bedienungsanleitung

Hunter

Hunter 44550 Bedienungsanleitung

Hunter

Hunter 44100 Bedienungsanleitung

Hunter

Hunter Internet Thermostat Bedienungsanleitung

Hunter

Hunter 44155C Bedienungsanleitung

Hunter

Hunter 44260 Bedienungsanleitung

Hunter

Hunter 44132 Bedienungsanleitung

Hunter

Hunter 44132 Bedienungsanleitung

Hunter

Hunter 44127 Bedienungsanleitung

Hunter

Hunter 47132 Bedienungsanleitung

Hunter

Hunter 42122 Bedienungsanleitung

Hunter

Hunter 44200 Bedienungsanleitung

Hunter

Hunter Set & Save 47200A Bedienungsanleitung

Hunter

Hunter Set 'n Save I 42204 Bedienungsanleitung

Hunter

Hunter 42996 Bedienungsanleitung

Hunter

Hunter 44277W Bedienungsanleitung

Hunter

Hunter 40020A Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung