Hussmann GSVM4060F Bedienungsanleitung

GSVM 4060F

Low Temperature

Self Contained

Vertical

Merchandiser

with Doors

P/N 3003960_A

April 2016

Installation &

Operation

Manual

IMPORTANT

Keep in store for

future reference!

MANUAL - IO SC GSVM 4060F

Spanish 3003961

French 3003962

P/N 3003960_A iii

IMPORTANT

KEEP IN STORE FOR FUTURE REFERENCE

Quality that sets industry standards!

12999 St. Charles Rock Road • Bridgeton, MO 63044-2483

U.S. & Canada 1-800-922-1919 • Mexico 1 800-890-2900

www.hussmann.com

Merchandiser must operate for 24 hours

before loading product!

Regularly check merchandiser temperatures.

Do not break the cold chain. Keep products

in freezer before loading into merchandiser.

These merchandisers are designed

for pre-frozen products only.

ANSI DEFINITIONS ................. vi

INSTALLATION

Certification ........................ 1-1

Hussmann Product Control ........... 1-1

Shipping Damage ................... 1-1

Location ........................... 1-1

Self Contained Location .............. 1-2

Model Description .................. 1-2

Unloading ......................... 1-2

Exterior Loading .................... 1-3

Shipping Skid ...................... 1-3

Merchandiser Leveling ............... 1-3

Optional Legs ...................... 1-3

Serial Plate Location ................. 1-4

Sealing Merchandiser to Floor ......... 1-4

Refrigeration Unit Access ............. 1-4

Checklists .......................... 1-5

ELECTRICAL / REFRIGERATION

Merchandiser Electrical Data .......... 2-1

Field Wiring ........................ 2-1

Power Switch ....................... 2-1

Electrical Connections . . . . . . . . . . . . . . . . 2-1

Electrical Outlet ..................... 2-1

Refrigeration (Self Contained) ......... 2-2

Safe-NET III Controller .............. 2-3

Safe-NET Display ................... 2-4

Safe-NET Start-Up .................. 2-4

Sequence of Operation ............... 2-5

Alarms and Codes ................... 2-6

Defrost Termination Switch ........... 2-6

Temperature Adjustment ............. 2-7

Typical Sensor to Control Config. ...... 2-8

START UP / OPERATION

Start-Up ........................... 3-1

Controls and Adjustments ............ 3-1

Load Limits ........................ 3-1

Stocking ........................... 3-1

Shelf Weight Limits .................. 3-2

MAINTENANCE

Care and Cleaning ................... 4-1

Do NOT Use: ...................... 4-1

Do: ............................... 4-1

Cleaning Discharge Honeycomb ....... 4-2

Cleaning Stainless Steel Surfaces ....... 4-2

Cleaning Solar Thermometer .......... 4-2

Cleaning Under Display Pan .......... 4-3

Cleaning Evaporation Pan ............ 4-3

Cleaning Coils ...................... 4-4

Removing Scratches from Bumper ...... 4-4

Equipment Checklist ................. 4-5

SERVICE

Replacing Fan Motors and Blades ...... 5-1

Cleaning Coils ...................... 5-1

LED Light Replacement .............. 5-2

GSVM Accessories .................. 5-2

Troubleshooting Guide ............... 5-3

Adjusting Doors .................... 5-6

APPENDIX

Part Numbers ..................... A-1

Plan View ......................... A-3

Cross Sections and Refrigeration Data .. A-4

Electrical Data ..................... A-5

Shipping Weights and Amps . . . . . . . . . . A-6

Wiring Diagram GSVM 4060F ....... A-6

WARRANTY

TABLE OF CONTENTS v

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. GSVM 4060F Merchandisers

P/N 3003960_A 1-1

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. GSVM 4060F Merchandisers

CERTIFICATION

These merchandisers are manufactured to

meet ANSI / National Sanitation Foundation

(NSF®)Standard #7 requirements. Proper

installation must be performed to maintain

these requirements. Near the serial plate, each

case carries a label identifying the type of

application for which the case was tested.

ANSI/NSF-7 Type I - Display Refrigerator / Freezer

Intended for 75°F / 55% RH Ambient Application

ANSI/NSF-7 Type II - Display Refrigerator / Freezer

Intended for 80°F / 55% RH Ambient Application

ANSI/NSF-7 - Display Refrigerator

Intended for Bulk Produce

HUSSMANN PRODUCT CONTROL

The serial number and shipping date of all

equipment is recorded in Hussmann’s files

for warranty and replacement part purposes.

All correspondence pertaining to warranty or

parts ordering must include the serial number

of each piece of equipment involved. This is to

ensure the customer is provided with the cor-

rect parts.

SHIPPING DAMAGE

All equipment should be thoroughly examined

for shipping damage before and during

unloading. This equipment has been carefully

inspected at our factory. Any claim for loss

or damage must be made to the carrier. The

carrier will provide any necessary inspection

reports and/or claim forms.

Apparent Loss or Damage

If there is an obvious loss or damage, it must

be noted on the freight bill or express receipt

and signed by the carrier’s agent; otherwise,

carrier may refuse claim.

Concealed Loss or Damage

When loss or damage is not apparent until

after equipment is uncrated, retain all packing

materials and submit a written response to the

carrier for inspection within 15 days.

LOCATION

These merchandisers are designed for

displaying products in air conditioned stores

where temperature is maintained at or below

the ANSI / NSF-7 specified level and relative

humidity is maintained at or below 55%.

Placing refrigerated merchandisers in direct

sunlight, near hot tables or near other heat

sources could impair their efficiency. Like

other merchandisers, these merchandisers are

sensitive to air disturbances. Air currents

passing around merchandisers will seriously

impair their operation. Do NOT allow air

conditioning, electric fans, open doors or

windows, etc. to create air currents around the

merchandiser.

INSTALLATION

Recommended operating ambient temperature is

between 75°F(23.9°C) to 80° (26.7°C). Maximum

relative humidity is 55%.

1-2 InstallatIon

P/N 3003960_A U.S. & Canada 1-800-922-1919 • Mexico 1 800-890-2900 • www.hussmann.com

SELF CONTAINED (LOCATION)

GSVM 4060F (at 80°F/55% relative humidity,

maximum ambient conditions) has front

condenserair intake and discharge. Maintain a

minimum clearance distance of two feet in front

of the merchandiser so that air discharge and air

intake is not obstructed.

MODEL DESCRIPTION

GSVM4060F vertical merchandisers are

designed for low temperature, pre-packaged

products at below freezing temperatures.

Carefully read and follow the instructions prior

operating the merchandiser.

UNLOADING

Unloading from Trailer:

Lever Bar (also known as a Mule, Johnson

Bar, J-bar, Lever Dolly, or Pry Lever)

Move the merchandiser as close as possible to

its permanent location and remove all packaging.

Check for damage before discarding packaging.

Remove all separately packed accessories such

as kits and shelves.

Improper handling may cause damage to the

merchandiser when unloading. To avoid damage:

1. Do not drag the merchandiser out of the

trailer. Use a Johnson bar (mule).

2. Use a forklift or dolly to remove the

merchandiser from the trailer.

Do NOT remove shipping crate until the

merchandiser is positioned

for installation.

Do NOT stand or walk on top of

merchandiser. Do not store items or

ammable materials atop the unit.

P/N 3003960_A 1-3

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. GSVM 4060F Merchandisers

EXTERIOR LOADING

Do NOT walk on top of merchandisers or

damage to the merchandisers and serious

personal injury could occur.

merchandisers are not structurally

designed to support external loading

such as the weight of a person. Do not place

heavy objects on the merchandiser.

SHIPPING SKID

Each merchandiser is shipped on a skid to

protect the merchandiser’s base, and to make

positioning the case easier.

Do not remove the shipping skid until the

merchandiser is near its final location. The

skid provides protection for both the merchan-

diser and the floor.

Remove the skid by raising one end of the

merchandiser approximately 6 inches. Block the

merchandiser securely, and remove the two skid

bolts from the raised end. Replace the bolts

with (provided) leg levelers. Repeat this proce-

dure at opposing end. Once the leg levelers are

secured in place, the merchandiser may be slid

off the skid and placed in its final location.

DO NOT TILT MERCHANDISER ON ITS

SIDE OR END WHEN REMOVING SKID.

Once the skid is removed, the merchandiser

must be lifted —NOT PUSHED— to reposition.

Check floor where merchandisers are to be set

to see if it is a level area. Determine the highest

part of the floor.

MERCHANDISER LEVELING

Besure to position merchandisers proper-

ly. Level the merchandiser by all four corners.

Merchandiser(s) must be installed level to

ensure proper operation of the refrigeration

system, and to ensure proper drainage of

defrost water.

OPTIONAL LEGS

NSF® approved legs replace the leg levelers if

required by local health codes. The legs raise

the case 6 inches for cleaning purposes. An

optional skirt kit can be provided to snap on

the legs.

This product may contain chemicals known

to the State of California to cause cancer,

birth defects, or other reproductive harm.

This warning is the result of the California State

law known as the California Safe Drinking Water

and Toxic Enforcement Act of 1986, which is

commonly referred to as “Proposition 65.”

This warning does not mean that Hussmann

products will cause cancer or reproductive

harm, or is in violation of any product-safety

standards or requirements. As claried by the

California State government, Proposition 65

can be considered more of a ‘right to know’ law

than a pure product safety law. When used as

designed, Hussmann believes that our products

are not harmful. We provide the Proposition 65

warning to stay in compliance with California

State law. It is your responsibility to provide

accurate Proposition 65 warning labels to your

customers when necessary. For more information

on Proposition 65, please visit the California

State government website.

For California Businesses:

1-4 InstallatIon

P/N 3003960_A U.S. & Canada 1-800-922-1919 • Mexico 1 800-890-2900 • www.hussmann.com

SERIAL PLATE LOCATION

The serial plate is located on the interior top,

left side of the merchandiser. It contains all

pertinent information such as model, serial

number, amperage rating, refrigerant type and

charge. This information will be needed to

install, service or order parts for the merchandis-

er.

SEALING MERCHANDISER TO FLOOR

If required by local sanitary codes, or if the

customer desires, merchandisers may be sealed

to the floor using a vinyl cove base trim. The

size needed will depend on how much varia-

tion there is in the floor, from one end of the

merchandiser to the other. Sealing of the lower

front and rear panels on self contained mod-

els may hamper their removal for servicing or

maintenance of the condensing unit.

NOTE: Do not allow trim to cover any intake

or discharge grilles located in the lower front

panel.

REFRIGERATION UNIT ACCESS

The lower front panel may be removed by

removing screw at bottom and lifting the panel

straight upward and over the tabs on which it

is hanging. The panel is installed by reversing the

above procedure.

Ensure lower front panel is flat against the

floor when installed to prevent air circulation

problems for self contained merchandisers.

Safe-NET III display is

mounted on left side of

access panel. Be careful not

to detach Safe-NET III cable

from display when removing

access panel.

Serial Plate

Lift up and

out to remove

access panel

Front Panel

Safe-NET III Display

Safe-NET III

Display

P/N 3003960_A 1-5

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. GSVM 4060F Merchandisers

Hussmann Self-Contained Refrigeration Equipment Start Up Check List

***Please note that failure to follow this start-up document may void your factory warranty***

Form HSCW01 Rev. 30MAY12 P/N 0525209_B

Step Startup Activity Check

1 Locate, read and maintain install/operation manual in a safe place for

future reference.

2 Examine unit. Confirm there is NO damage or concealed damage.

3 Level the unit, side to side and front to rear.

4 Remove all shipping brackets/compressor straps/bolts etc.

5 Unit must be run on a dedicated electrical circuit without the use of

an extension cord.

6 Ensure that the proper electrical requirements for the equipment are

supplied.

7 Verify field electrical connections are tight.

8 Verify all electrical wiring is secured and clear of any sharp edges or

hot lines.

9 Verify the condensate drain line is properly trapped and pitched.

10 Verify all required clearances on the sides and back of unit.

11 Verify there are no air disturbances external to the unit. Heat and air

registers, fans, and doors etc.

Advise owner/operator that merchandiser must operate at temperature for 24 hrs prior to loading

with product.

LEGAL DISCLAIMER:

Hussmann shall not be liable for any repair or replacements made without the written consent of Hussmann, or when the product is installed or operated in a manner

contrary to the printed instructions covering installation and service which accompanied such product.

Inhaltsverzeichnis

Andere Hussmann Kaufmann Handbücher

Hussmann

Hussmann Impact Excel M5X-GE Bedienungsanleitung

Hussmann

Hussmann VR3-M-EP Original Betriebsanleitung

Hussmann

Hussmann MicroSC ISMGG2DA-A Bedienungsanleitung

Hussmann

Hussmann D5X-HEP Bedienungsanleitung

Hussmann

Hussmann IMPACT LWU Bedienungsanleitung

Hussmann

Hussmann GC Bedienungsanleitung

Hussmann

Hussmann NAV-4 Bedienungsanleitung

Hussmann

Hussmann IMPACT Excel B1X-GE Bedienungsanleitung

Hussmann

Hussmann Impact Excel M5X-EP Bedienungsanleitung

Hussmann

Hussmann NRCV Bedienungsanleitung

Hussmann

Hussmann Q3-M/FV-EP Bedienungsanleitung

Hussmann

Hussmann IMPACT M5 Bedienungsanleitung

Hussmann

Hussmann AB Bedienungsanleitung

Hussmann

Hussmann IMPACT ED1 Bedienungsanleitung

Hussmann

Hussmann ASCS Betriebsanleitung

Hussmann

Hussmann IMPACT LW Bedienungsanleitung

Hussmann

Hussmann Impact C5HE Bedienungsanleitung

Hussmann

Hussmann M1XD-E Bedienungsanleitung

Hussmann

Hussmann IMPACT ED1 Bedienungsanleitung

Hussmann

Hussmann HGL-1BS Kurzanleitung

Hussmann

Hussmann Impact C6LE Bedienungsanleitung

Hussmann

Hussmann BEXD-A Bedienungsanleitung

Hussmann

Hussmann HEDW Bedienungsanleitung

Hussmann

Hussmann ESGMS Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Dixie Narco

Dixie Narco DNCB 501E Bedienungsanleitung

APW Wyott

APW Wyott Racer DMXD-30H Bedienungsanleitung

Hoshizaki

Hoshizaki KD-90C Bedienungsanleitung

Summit

Summit SCR1006 Bedienungsanleitung

Delfield

Delfield Shelleyspeed SPM-28E Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions GLEE 40 Bedienungsanleitung

Kysor/Warren

Kysor/Warren GranBering KW Leitfaden

Crane

Crane BevMAX Refresh 6 Media Bedienungsanleitung