IBM 0367 Bedienungsanleitung

AS/400e 170 or 250

0367 Operations Console

and0381RemoteControl

Panel Cable Instruction

Ve r s i o n 4

SENG-0367-04



AS/400e 170 or 250

0367 Operations Console

and0381RemoteControl

Panel Cable Instruction

Ve r s i o n 4

SENG-0367-04



Note

Before using this information and the product it supports, be sure to read the “Safety and Environmental Notices” on

page iii and the “Notices” on page 23.

Fifth Edition (July 2000)

This edition applies only to reduced instructions set computer (RISC) systems.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Safety and Environmental Notices

Danger Notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people.

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the products that attach to the system. It is the

customer’s responsibility to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock. (RSFTD201)

DANGER

To prevent a possible electrical shock when installing the system, ensure that

the power cords for all devices are unplugged before installing signal cables.

(RSFTD202)

DANGER

To prevent a possible electrical shock when adding or removing any devices

to or from the system, ensure that the power cords for those devices are

unplugged before the signal cables are connected or disconnected. If possible,

disconnect all power cords from the existing system before you add or

remove a device. (RSFTD203)

DANGER

To prevent a possible electrical shock during an electrical storm, do not

connect or disconnect cables or station protectors for communications lines,

display stations, printers, or telephones. (RSFTD003)

DANGER

To prevent a possible electrical shock from touching two surfaces with

different electrical grounds, use one hand, when possible, to connect or

disconnect signal cables. (RSFTD004)

Caution Notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition.

CAUTION:

Telecommunications Statement: This unit contains over-voltage circuits between

the ac power outlet and the unit. These circuits meet the standard limits

described in International Electrical Commission (IEC) 664, installation category

II. It is the customer’s responsibility to ensure that the power outlet meets the

standards of IEC 664, installation category II. (RSFTC214)

Laser Safety Information

CAUTION:

This product may contain a CD-ROM which is a class 1 laser product.

(RSFTC240)

Product Recycling and Disposal

Components of the system, such as structural parts and circuit cards, can be

recycled where recycling facilities exist. IBM does not currently collect and recycle

used IBM products from customers in the United States other than those products

that are involved in trade-in programs. Companies are available to disassemble,

reutilize, recycle, or dispose of electronic products. Contact an IBM account

representative for more information.

The system unit contains batteries and circuit boards with lead solder. Before you

dispose of this unit, these batteries and circuit boards must be removed and

discarded according to local regulations or recycled where facilities exist. This book

contains specific information on each battery type where applicable.

Battery Return Program

In the United States, IBM has established a collection process for reuse, recycling,

or proper disposal of used IBM batteries and battery packs. For information on

proper disposal of the batteries in this unit, please contact IBM at 1-800-426-4333.

Please have the IBM part number that is listed on the battery available when you

make your call. For information on battery disposal outside the United States,

contact your local waste disposal facility.

Environmental Design

The environmental efforts that have gone into the design of the system signify

IBM’s commitment to improve the quality of its products and processes. Some of

these accomplishments include the elimination of the use of Class I

ozone-depleting chemicals in the manufacturing process, reductions in

manufacturing wastes, and increased product energy efficiency. For more

information, contact an IBM account representative.

iv AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5

Installation Instruction

The prerequisite for the Operations console cable (feature number 0367) is the 2721

or 2745 card. If you need to install a 2721 or 2745 card, install it first, then return to

these instructions.

Ensure that your AS/400 Operating System is V4R3M0 or later.

Note: To verify, enter DSPPTF on the AS/400 Main menu. Look at the line Release of

base option.

This instruction only sets up a console that is directly connected to your AS/400.

This feature is customer installed. It will take approximately 1 hour to install the

hardware. However, you may elect not to perform this feature installation yourself.

You may contact IBM or an Authorized Dealer to make arrangements for them to

perform the feature installation for a fee.

You need to allow additional time to complete your jobs, back up your system, IPL

your system, and verify your hardware configuration.

Note: When you install the Operations Console cable (Feature 0367) and the

Remote Control Panel cable (Feature 0381), you may receive instructions for

each feature. The instructions are identical; use only one set of instructions.

If there are incorrect, missing or visibly damaged parts, contact one of the

following:

vYour authorized dealer

vPoint of purchase (for example, IBM Direct)

vIBM Rochester Manufacturing Automated Information Line (R-MAIL)

–1-800-300-8751 (United States)

–1-507-253-5242 (worldwide)

Determine if there are any existing prerequisites before you install your new

feature. Go to this Web site and locate your feature number and OS/400 release

and check the prerequisites.

http://as400service.ibm.com/s_dir/slkbase.NSF/

Then do the following to get to the Customer Install Features Prerequisites:

1. Select All Documents

2. Select Collapse

3. Select General Information

4. Select Offerings

5. Select Feature Prerequisites

6. Select Customer Install Features Prerequisites

Before You Begin

Ensure that your AS/400 Operating System is at V4R3M0 or later.

Note: To verify, enter DSPPTF on the AS/400 Main menu. Look at the line Release of

base option.

Ensure that your PC or workstation for Operations Console is Windows 95 or

Windows NT. Operations Console is not supported on a Windows 3.1 workstation.

Note: When you see Windows 95, it also applies to Windows 98.

Ensure that the following minimum requirements are met on the PC being used as

your Operations Console.

vOperations Console System requirements for Local Controlling Systems (LCS):

–Operating System

- If used as a stand alone LCS, the operating system can be either a

Windows 95 or a Windows NT Workstation 4.0 with “Remote Access to the

Network”installed in the Network Folder.

- If used as a Local Controlling System (LCS) to support a Remote

Controlling System (RCS), the operating system must be Windows NT

Workstation 4.0 with “Remote Access to the Network”installed in the

Network Folder.

- One or both of the following cables:

vOperations Console Cable, part number 97H7557

vRemote Control Cable, part number 97H7591

- 9600 baud modem minimum, if the LCS will receive calls from an RCS or

this workstation will be an LCS and an RCS

- One available communications (COM) port for console

- One available communications (COM) port for control panel

Notes:

1. For Windows NT, you can check for“Remote Access to the Network”by

doing the following:

__ a. Click on Start.

__ b. Click on Settings.

__ c. Click on Control Panel.

__ d. Click on Network.

If you can open the Network Folder, you have met network requirements.

Click on Cancel.

If you cannot open the Network Folder, you do not have “Remote Access

to the Network”installed. Select Yes to install.

2. For Windows 95, you can check for the network requirements by doing

the following:

__ a. Click on Start.

__ b. Click on Settings.

__ c. Click on Control Panel.

__ d. Click on Network.

__ e. Is TCP/IP listed?

No Yes

↓Click on OK. You have satisfied the network requirements.

Go to step 2m on page 3.

2AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5

__ f. Click on Add.

__ g. Select Protocol.

__ h. Click on Add.

__ i. Select Microsoft listed under ″Manufacturers″.

__ j. Select TCP/IP listed under ″Network Protocols″.

__ k. Click on OK twice.

__ l. Select Yes to restart the PC.

__ m. Window 95 requires Dial Up Networking (DUN). To verify the

level of DUN on your system, do the following

__ 1) Click on Start

__ 2) Click on Settings

__ 3) Click on Control Panel

__ 4) Click on System

Write the number that is located below Microsoft Windows 95

on a piece of paper. For example, 4.00.950 would be the base

code as shipped on the original Windows 95 compact disc

(CD). Your version may also have a letter after that number.

__ 5) Click on Cancel

__ 6) Click on Add/Remove Programs

Is Microsoft Dial-Up Networking (DUN) Upgrade listed?

Yes No

↓You will be instructed how to install Dial-Up

Networking later in this document.

__ 7) Click on Cancel.

Note: If you are using either COM3 or COM4, be sure that the addresses and

the IRQ settings do not conflict with other hardware resources.

Installing the Cable

__ 1. Ensure that all jobs are complete.

__ 2. When all jobs are complete, type

pwrdwnsys immed

on an AS/400 command line and press the Enter key.

Note: Should you encounter difficulties during the installation, contact

your authorized dealer or service provider.

__ 3. When the AS/400 is powered down, power off all PCs and devices, such as

printers and displays, that are connected to the system unit.

__ 4. Unplug any power cords, such as printers and displays, from electrical

outlets.

__ 5. Unplug the system unit power cord from the electrical outlet.

__ 6. Remove the system unit back cover, if not already removed.

__ 7. Do you have cable part number 97H7557 to connect?

Yes No

↓You only have cable part number 97H7591 to connect. Go to step

13 on page 5.

Installation Instruction 3

__ 8. Locate position C08 (Figure 1) on the back of your system unit.

__ 9. Unplug the system unit power cord from the electrical outlet.

__ 10. Are there cables that are connected to the 2721 or 2745 card installed in

position C08?

Yes No

↓Go to step 17 on page 6.

__ 11. Disconnect the system unit console cable (Figure 2 on page 5) that is

connected to Port 1 (right connector). Disconnect the other end of the cable

from your PC. The cable will not be used.

Base Unit (Back View) Base Unit with Expansion Unit (Back View)

Figure 1. Adapter Card Positions

4AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Computerhardware Handbücher

IBM

IBM Power System 9009-41A Bedienungsanleitung

IBM

IBM 9332 Bedienungsanleitung

IBM

IBM ATA 133 Bedienungsanleitung

IBM

IBM PPC440X5 CPU Core Bedienungsanleitung

IBM

IBM eserver 225 Series Bedienungsanleitung

IBM

IBM 7311-D11 Gebrauchs- und Pflegehandbuch

IBM

IBM SAS Connectivity Cars Bedienungsanleitung

IBM

IBM 7133 D40 Bedienungsanleitung

IBM

IBM 3745 Series Bedienungsanleitung

IBM

IBM eserver Cluster 1350 Montage- und Wartungsanleitung

IBM

IBM QLogic 4Gb Fibre Channel Expansion Card Bedienungsanleitung

IBM

IBM MPC603EC Bedienungsanleitung

IBM

IBM System x Education M5000 Series Bedienungsanleitung

IBM

IBM p5 550 Installationsanleitung

IBM

IBM 4331 Bedienungsanleitung

IBM

IBM N2225 Bedienungsanleitung

IBM

IBM 6611 Bedienungsanleitung

IBM

IBM 4764 Bedienungsanleitung

IBM

IBM 2740-1 Benutzerhandbuch

IBM

IBM 3290 T Bedienungsanleitung

IBM

IBM Power 730 Express 8231-E2B Bedienungsanleitung

IBM

IBM Remote Supervisor Adapter II Bedienungsanleitung

IBM

IBM 19K4543 Bedienungsanleitung

IBM

IBM 55PUS8118 SCSI-2 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung