IBM System Storage EXN2000 Handbuch

EXN2000

Installation and Setup Instructions

IBM System Storage

Customer-supplied items needed for setup:

#2 Phillips screwdriver

ESD wrist strap

Pointed tool for setting ID switches

7mm nut driver

This document provides installation and setup instructions for the IBM System

Storage EXN2000 storage expansion unit. Additional information about the

EXN2000 can be found in the

This document presents the EXN2000 information previously found in the

GC26-7786.

IBM System Storage EXN2000 Storage Expansion

Unit Hardware and Service Guide

IBM System Storage EXN1000 and EXN2000 Installation and Setup Instructions

Note:

Need help?

If you encounter any difficulties while setting up your system, contact IBM service

and support for assistance. Information can also be found at the following Web

site:

www.ibm.com/storage/support/nas/

Read the safety notices:

Before continuing, make sure that you have reviewed the safety notices in the

documentation that came with this system. Do not plug any cables into the

system, adapters, or any electrical outlets until you have reviewed the safety

information and followed the procedures in this document.

1Unpacking the EXN2000 (expansion unit)

EXN2000

(expansion unit)

Note: The contents of the box will differ based

on the model you purchased. See Step 1.1 for a

list of contents for specific models.

Important:

If your system was shipped already assembled and cabled in a rack, go

directly to the for the storage system to

boot the system.

Installation and Setup Instructions

Accessory kit:

- IBM rail kit

- Power cables

- Setup kit

1.1

1.2

1.3

Remove the expansion unit and its tray using the handles built into the

cardboard tray. Place the expansion unit and tray on a table.

Remove the top portion of the plastic surrounding the expansion unit.

32 kg (70.5 lb)

Verify that the shipping packages include the following items:

EXN2000 (2863-001)

1 EXN2000

1 Publications

2 Power cords

ables

May be present:

1 IBM rail kit

1Wriststrap,ESD

1 Enclosure shelf Ids label

Miscellaneous data c

Small Form Factor Pluggable (SFP) module

DANGER: Expansion units are extremely heavy. To avoid injuring yourself

or damaging an expansion unit, you must work with at least two other

people when you install an expansion unit in the rack. Do not remove the

disk drives to reduce the weight.

Caution: Use safe practices when lifting.

Installing the rails in an IBM 19-inch rack

Note: Read this document in its entirety before proceeding.

2.1 Loosen (but do not remove) the four rail adjustment screws on each rail.

2.2

Right rail

Left rail

Front of rack

Rear of rack

Rail adjustment

screws

Locating pins

Use the figure on the next page for reference. At the front of the rack,

position the right-hand rail into the rack at the appropriate EIA location

(make sure that the two locating pins seat properly). The bottom of the rail

should line up with the bottom EIA boundary.

When installed, each EXN2000 unit will occupy a 3U space.

Using two silver pan head M5 screws, attach the rail to the front of the rack

using holes H3 and H7. T

Note:

ighten these screws with a screwdriver.

2.3 At the rear of the rack, position the rail at the same EIA location used in

step 2.2 (make sure that the locating pins seat properly). Using two silver

pan head M5 screws,

Tighten these screws with a screwdriver.

attach the rail to the rack using holes H2 and H8.

2.4 Tighten the four rail adjustment screws on the installed rail.

2.5 Repeat steps 2.2 through 2.4 for the left-hand rail.

2.6 Repeat steps 2.1 through 2.5 if installing a second EXN2000.

Section of rack EIA rail

Locating pins

Bottom rail screws

REAR

Left and Right

Rails

Chassis attach screws

FRONT

Left and Right

Rails

Top rail screws

Locating pins

Chassis attach screws 1 EIA unit (1U)

Bottom rail screws

Top rail screws

3.1 From the front of the rack, place the expansion unit onto the rails and

slide it in until the front mounting bracket of the expansion unit is flush

with the frame rails of the rack.

3Installing the expansion unit into the rack

3.2

32 kg (70.5 lb)

Caution: Use safe practices when lifting.

DANGER: Expansion units are extremely heavy. To avoid injuring yourself

or damaging an expansion unit, you must work with at least two other

people when you install an expansion unit in the rack. Do not remove the

disk drives to reduce the weight.

Note: Verify the shelf IDs before installing into the rack. All shelf IDs should

be correct and sequential in the individual loop(s). If the filer and expansion

unit were configured together by manufacturing, these IDs are already set.

The label on the front should match the switch on the back. For more

information, refer to the .EXN2000 Hardware and Service Guide

At the front of the rack, using four black hex head M5 screws in the H2

and H8 holes, secure the system unit to the rack by threading the screws

through the system unit bracket and the rack frame rail into the threaded

rail nuts. Tighten the screws using the 7mm nut driver.

3.3 From the rear of the rack, use two silver pan head M5 screws to attach

the rear of the chassis to the rails as shown below.

Screws

4.1 Make sure that all expansion unit speed switches are set to the correct

position for your application.

For example, if connecting to an N3700 storage system, the speed switch

must be set to the 1Gb position. If connecting to an N5000 series or an

N7000 series storage system, the speed switch must be set to the 2Gb

position.

Use the following diagram for reference:

Setting the speed switch

1Gb 2Gb

Shelf ID

Gb switch

(set to 1 Gb)

Mute button

Out port

In port activity LED

In port

Out port activity LED

Fault LED

Speed (2 Gb) LED

Shelf ID - close-up view

5Grounding expansion units

5.1 If only one expansion unit is being used, go to Step 6, "Installing the

power cables" on page 9.

If two or more expansion units are being used continue with the

following.

Using the grounding kit, fasten the lug, fasten the lug at one end of the

0.25m grounding cable to one of the two threaded inserts (adjacent to

the power supply receptacles as indicated by a ground symbol) at the

back of the expansion unit using the M5 x 0.5-inch screw.

If additional expansion units need to be grounded, continue attaching

the grounding cables from unit to unit, overlaying the hole on one end

of the grounding cable from one to the next.

Note: For proper grounding, you must fasten your expansion unit(s)

together. Use the provided braided copper grounding cables and screws

(may be in the rail kit).

Dual expansion unit grounding Multiple expansion unit grounding

Grounding

cable

Grounding

cables

Inhaltsverzeichnis

Andere IBM Lagerung Handbücher

IBM

IBM DS3950 Betriebsanleitung

IBM

IBM Ultrastar 36XP Bedienungsanleitung

IBM

IBM 7212 102 Bedienungsanleitung

IBM

IBM ESS 5000 SC Series Montageanleitung

IBM

IBM TS7700 Series Bedienungsanleitung

IBM

IBM 3803 Bedienungsanleitung

IBM

IBM FlashSystem 9150 Handbuch

IBM

IBM Travelstar 6GT Bedienungsanleitung

IBM

IBM 3420 Bedienungsanleitung

IBM

IBM DS3500 Bedienungsanleitung

IBM

IBM FlashSystem A9000R Kurzanleitung

IBM

IBM Storwize V7000 Bedienungsanleitung

IBM

IBM DBCA-206480 - Travelstar 6.4 GB Hard Drive Bedienungsanleitung

IBM

IBM DTNA-21800 Bedienungsanleitung

IBM

IBM N2115 Installationshandbuch

IBM

IBM 220 Bedienungsanleitung

IBM

IBM ATA-3 Bedienungsanleitung

IBM

IBM N Series Montageanleitung

IBM

IBM 2498-B40 Bedienungs- und Montageanleitung

IBM

IBM DS3500 Betriebsanleitung

IBM

IBM N2225 Bedienungsanleitung

IBM

IBM DR550 V3.0 Bedienungsanleitung

IBM

IBM System Storage DS4000 Betriebsanleitung

IBM

IBM ThinkPad Dock II Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung