2 Sets the VE-PG2 to Selective call mode
1 Connects transceivers and LAN to the VE-PG2
MODE DC LAN TRX1 TRX2 TRX3 IN
+ + +
OUT SW ABC
GROUND
q
e
w
r
[TRX2] Calling number (DTMF): 2
To the [TRX2] port
To the [TRX1] port
(192.168.0.2)
[TRX1] Calling number (DTMF): 1
[Area A]
[Area B]
VE-PG2
Connect the transceiver’s microphone connector and speaker jack.
Transceiver A
channel 1
Transceiver C
channel 2
Transceiver B
channel 1
Transceiver D
channel 2
Connect the transceiver’s microphone connector and speaker jack.
NOTE: First, connect the transceiver
to the VE-PG2 using the specified
connection cable. Then turn ON the
power to the transceiver and the
VE-PG2.
NOTE: First, connect the transceiver
to the VE-PG2 using the specified
connection cable. Then turn ON the
power to the transceiver and the
VE-PG2.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074. (For the repeaters)
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable or connect the cables to [LAN]
may damage the VE-PG2, transceivers or repeaters.
Turn the transceivers’ power ON,
and then set the transceiver A
volume to the 12 o’clock position.
Turn the transceivers’ power ON,
and then set the transceiver C
volume to the 12 o’clock position.
Connect to the transceiver’s speaker jack.
Connect to the transceiver’s speaker jack.
CAUTION:
To connect the transceivers or repeaters, use only the following cables:
OPC-2073 (For the transceivers) or OPC-2074. (For the repeaters)
Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.
Using another cable, like an Ethernet cable, or connecting the cables to
[LAN] may damage the VE-PG2, transceivers or repeaters.
NOTE: When using the repeater, connect the optional OPC-2074 to the repeater’s ACC connector.
Repeater’s rear panel
OPC-2074
ACC connector
MODE DC LAN TRX1 TRX2 TRX3 IN
+ + +
OUT SW ABC
Connect the specified cables to
[TRX1], [TRX2] or [TRX3] only.
Set External I/O (D-sub 25) port setting* to Ext. I/O 18 Output Low Voltage 2.
*The CS-FR5000 cloning software and OPC-1122U cloning cable are required when you set External I/O D-sub 25 port setting.
1. “Operating mode setting” setting“Operating mode setting” settingOperating mode setting” setting” setting
Select
Click
12
Click
Selective call mode setting
5. How to communicate
1
2
Confirm the “Call destination number setting list” as“Call destination number setting list” asCall destination number setting list” as” asas
shown below.
NOTE:
• If you construct RoIP system with some VE-PG2s,
you can construct the system only to set each “Call“CallCall
destination number setting list”.”..
• “Call destination number setting list” has below 3“Call destination number setting list” has below 3Call destination number setting list” has below 3
buttons.
[Edit] : Click this button to edit the index setting.
[Delete] : Click this button to delete the index setting.
[Delete all] : Click this button to delete all data in the list.
3
2 Sets the VE-PG2 to Selective call mode (Continued)
This setting example refers to the connections in the far
top left illustration. Follow the steps for transceiver B calling
transceiver D.
qSet “Call destination number setting” for the Area“Call destination number setting” for the AreaCall destination number setting” for the Area” for the Areafor the Area
B shown to the left.
(Example) Set “Index” to “2”, “Call destination number”“Index” to “2”, “Call destination number”Index” to “2”, “Call destination number”” to “2”, “Call destination number”to “2”, “Call destination number”“2”, “Call destination number”2”, “Call destination number””, “Call destination number”, “Call destination number”“Call destination number”Call destination number””
to “2”, “Call destination VE-PG2 address”“2”, “Call destination VE-PG2 address”2”, “Call destination VE-PG2 address””, “Call destination VE-PG2 address”, “Call destination VE-PG2 address”“Call destination VE-PG2 address”Call destination VE-PG2 address””
to “192.168.0.2” and “Call destination“192.168.0.2” and “Call destination192.168.0.2” and “Call destination” and “Call destinationand “Call destination“Call destinationCall destination
VE-PG2 port” to “Transceiver 2(TRX2)”.” to “Transceiver 2(TRX2)”.to “Transceiver 2(TRX2)”.“Transceiver 2(TRX2)”.Transceiver 2(TRX2)”.”..
wClick [Save].
2
2. “Numbering plan” setting“Numbering plan” settingNumbering plan” setting” setting
qMove the mouse pointer to “Connection setting”,“Connection setting”,Connection setting”,”,,
and click “Numbering plan”.“Numbering plan”.Numbering plan”.”..
wSet “Call destination number setting” for the Area
A shown to the left.
(Example) Set “Index” to “1”, “Call destination number”“Index” to “1”, “Call destination number”Index” to “1”, “Call destination number”” to “1”, “Call destination number”to “1”, “Call destination number”“1”, “Call destination number”1”, “Call destination number””, “Call destination number”, “Call destination number”“Call destination number”Call destination number””
to “1”, “Call destination VE-PG2 address”“1”, “Call destination VE-PG2 address”1”, “Call destination VE-PG2 address””, “Call destination VE-PG2 address”, “Call destination VE-PG2 address”“Call destination VE-PG2 address”Call destination VE-PG2 address””
to “192.168.0.2” and “Call destination“192.168.0.2” and “Call destination192.168.0.2” and “Call destination” and “Call destinationand “Call destination“Call destinationCall destination
VE-PG2 port” to “Transceiver 1(TRX1)”.” to “Transceiver 1(TRX1)”.to “Transceiver 1(TRX1)”.“Transceiver 1(TRX1)”.Transceiver 1(TRX1)”.”..
eClick [Save].
1
qAfter making the connections as shown to the
above, turn transceivers A and C power ON, then
open the setting screen with your browser (see the
Installation guide q).
wClick the “Operating mode setting” in the“Operating mode setting” in theOperating mode setting” in the” in thein the
“Connection setting”, and then select “SelectiveConnection setting”, and then select “Selective”, and then select “Selective, and then select “Selective“SelectiveSelective
call mode”.”..
eClick the [Save and Reboot] button.
rClick [Back] on the screen after reboot finishes
(about 30 seconds later).
Click [OK] when the dialog box below appears.
• “Connection setting” will be return to default when“Connection setting” will be return to default whenConnection setting” will be return to default when” will be return to default whenwill be return to default when
the “Operating mode” setting is modified.“Operating mode” setting is modified.Operating mode” setting is modified.” setting is modified.setting is modified.
• Save the VE-PG2 setting to the setting file, if
necessary.
Refer to the VE-PG2 instruction manual (PDF file:
Download from the Icom web site) for details.
Hold down transceiver B’s [PTT], and push [2]
and [#] to transmit 2 and # DTMF signals to call to
transceiver D.
Release transceiver B’s [PTT] to receive.
Transceiver D sounds beep tone, then start
communication via the VE-PG2.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6838W-3US Printed in Japan
© 2010 Icom Inc.
4. Transceiver setting
Turn transceivers B and D power ON, and select the
same operating channel as transceivers A and C.
• Set the same channel for all the transceivers, to
communicate with the transceivers A and C.
See the transceiver’s instruction manual when
setting the channel, if necessary.
(Example) I n t h e i l l u s t r a t i o n t o t h e l e f t , s e t
transceivers A and B (Area A) to channel
1, and transceivers C and D (Area B) to
channel 2.
2
This setting example refers to the connections in the far top
left illustration.
Select
Click
Enter
Select
Select
Click
Enter
Select
Confirm
While holding down transceiver D’s [PTT], speak into
the microphone at your normal voice level.
Release transceiver D’s [PTT] to receive.
While holding down transceiver B’s [PTT], speak into
the microphone at your normal voice level.
Release transceiver B’s [PTT] to receive.
3
4
VE-PG2 finishes communication when no audio is
applied to transceivers B and D for 15 seconds. Or hold
down the transceiver’s [PTT] and [#] for 1 second to
transmit a # DTMF signal from the transceivers B or D.
5
3. Transceiver control setting
3. Transceiver control setting (Continued)
Select
Click
Selective call mode setting
Selective call mode setting
Set transceivers A and C AF volume to the 12 o’clock’clockclock
position.
1
qMove the mouse pointer to “Connection setting”“Connection setting”Connection setting”
and then to the drop down menu “TRX/EXT”, then“TRX/EXT”, thenTRX/EXT”, then
click “Transceiver 1 (TRX1)”.
wSet “Calling notice tone to Transceiver” to “Notice“Calling notice tone to Transceiver” to “NoticeCalling notice tone to Transceiver” to “Notice“NoticeNotice
tone 2”.
eSet “Send connect success tone to Transceiver” to“Send connect success tone to Transceiver” toSend connect success tone to Transceiver” to
“Notice tone 2”.Notice tone 2”.
rSet “Disconnect notice tone to Transceiver” to“Disconnect notice tone to Transceiver” toDisconnect notice tone to Transceiver” to
“Notice tone 3”.Notice tone 3”.
tSet “Send connect failure tone to Transceiver” to“Send connect failure tone to Transceiver” toSend connect failure tone to Transceiver” to
“Notice tone 3”.Notice tone 3”.
1
yClick [Save].
uMove the mouse pointer to “Connection setting”“Connection setting”Connection setting”
and then to the drop down menu “TRX/EXT”, then
click “Transceiver 2 (TRX2)”.
iSet same steps as w–y.
1
Connect the VE-PG2 according to steps q– rin the illustration below.
