Icom VE-PG2 Bedienungsanleitung

SELECTIVE CALL MODE APPLICATION

VE-PG2 SETTING SCREEN

MAINTENANCE

REFERENCE

BRIDGE MODE APPLICATION 1

INSTRUCTION MANUAL

RoIP GATEWAY

VE-PG2

TABLE OF CONTENTS

1 BRIDGE MODE APPLICATION.............................................................................5

 ■ Unicast mode operation......................................................................................6

2 SELECTIVE CALL MODE APPLICATION ..........................................................17

 ■ Using with in-house sound system ...................................................................18

 ■ Using with an emergency device......................................................................28

 ■ Using with a headset ........................................................................................39

3 VE-PG2 SETTING SCREEN ................................................................................49

 ■ Setting screen descriptions ..............................................................................52

 ■ Connection setting (Bridge mode) ....................................................................53

3-1 Operating mode .........................................................................................53

3-2 IP network connection Transceiver 1 (TRX1)–Transceiver 3 (TRX3) .........57

3-3 IP network connection EXT Input (EXT IN)................................................61

3-4 IP network connection EXT Output (EXT OUT) .........................................65

3-5 IP network connection EXT I/O (EXT)........................................................68

3-6 IP network connection Emergency notice ..................................................71

3-7 TRX/EXT Transceiver 1 (TRX1)–Transceiver 3 (TRX3)..............................74

3-8 TRX/EXT EXT Input (EXT IN) ....................................................................78

3-9 TRX/EXT EXT Output (EXT OUT) .............................................................83

3-10 VoIP call detail Common setting...............................................................85

3-11 Emergency notice ....................................................................................87

3-12 Abnormal condition monitor .....................................................................88

 ■ Connection setting (Selective call mode)..........................................................89

3-13 Operating mode .......................................................................................89

3-14 IP network connection Transceiver 1 (TRX1)–Transceiver 3 (TRX3) .......91

3-15 IP network connection EXT Input (EXT IN)..............................................93

3-16 IP network connection Emergency notice ................................................95

3-17 TRX/EXT Transceiver 1 (TRX1)–Transceiver 3 (TRX3)............................96

3-18 TRX/EXT EXT Input (EXT IN) ................................................................102

3-19 TRX/EXT EXT output (EXT OUT) ..........................................................107

3-20 VoIP call detail Transceiver 1 (TRX1) – Transceiver 3 (TRX3) ...............115

3-21 VoIP call detail EXT Input (EXT IN)........................................................117

3-22 VoIP call detail EXT Output (EXT OUT) .................................................119

3-23 VoIP call detail Common setting.............................................................121

3-24 Numbering plan......................................................................................124

3-25 Priority call control..................................................................................128

3-26 Emergency notice ..................................................................................129

TABLE OF CONTENTS

3-27 Abnormal condition monitor ...................................................................130

 ■ Network setting...............................................................................................131

3-28 LAN IP....................................................................................................131

■System setting ................................................................................................133

3-29 Administrator ..........................................................................................133

3-30 Clock ......................................................................................................134

3-31 SYSLOG ................................................................................................135

3-32 SNMP.....................................................................................................136

■Information......................................................................................................137

3-33 Network information ...............................................................................137

3-34 SYSLOG ................................................................................................139

3-35 Call/Reception record.............................................................................140

3-36 Information list for IP connection............................................................141

4 MAINTENANCE.................................................................................................143

 ■ How to restrict of access ...............................................................................144

 ■ How to set the VE-PG2 internal clock time.....................................................145

 ■ How to save the VE-PG2 setting to the PC ....................................................146

 ■ How to load the saved file to the VE-PG2.......................................................147

 ■ How to initialize the VE-PG2...........................................................................148

 ■ Firmware updating..........................................................................................150

5 REFERENCE .....................................................................................................155

 ■ Troubleshooting ..............................................................................................156

 ■ Connect with the VE-PG2 using Telnet...........................................................158

SECTION 1

BRIDGE MODE APPLICATION

This section describes the VE-PG2 setting example in the bridge mode.

1 BRIDGE MODE APPLICATION.............................................................................5

 ■ Unicast mode operation......................................................................................6

BRIDGE MODE APPLICATION

In the Unicast mode, the VE-PG2 specifies a port number, IP address and calls a

specified transceiver that is connected to the VE-PG2.

The following descriptions are based on the step by step example shown below.

Example: Operating VE-PG2 in local area network.

Transceiver B3

[TRX2]

Transceiver A2

[TRX1]

(Port number: 21500)

HUB

Transceiver A1

[TRX1]

[Area A]

[LAN]

192.168.0.2

VE-PG2

1 2 3 4 5

[Area B]

Transceiver B2

[TRX1]

(Port number: 21500)

[TRX1]

Transceiver B1

[LAN]

192.168.0.3

VE-PG2

If you connect the VE-PG2 to a global network (internet),

you can communicate anywhere through the IP network

without using hub.

CAUTION:

To connect the transceivers or repeaters, use only the following cables:

OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).

Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.

Using another cable, like an Ethernet cable may damage the VE-PG2,

transceivers or repeaters.

CAUTION:

To connect the transceivers or repeaters, use only the following cables:

OPC-2073 (For the transceivers) or OPC-2074 (For the repeaters).

Connect the specified cables to [TRX1], [TRX2] or [TRX3] only.

Using another cable, like an Ethernet cable may damage the VE-PG2,

transceivers or repeaters.

Connect to the transceiver A2’s speaker jack.

Connect to the transceiver B2’s speaker jack.

NOTE: First, connect the transceiver

to the VE-PG2 using the optional

OPC-2073. Then turn ON the power

to the transceiver and the VE-PG2.

NOTE: First, connect the transceiver

to the VE-PG2 using the optional

OPC-2073. Then turn ON the power

to the transceiver and the VE-PG2.

Turn the transceivers’ power ON, and

then set the Transceiver A2’s volume

control to the 12 o’clock position.

Turn the transceivers’ power ON, and

then set the Transceiver B2’s volume

control to the 12 o’clock position.

■Unicast mode operationUnicast mode operation

BRIDGE MODE APPLICATION 1

Step 1 [Area A]–Setting the IP address for Area A

Place the mouse pointer on “Network setting,” and then click “LAN IP” shown in the“Network setting,” and then click “LAN IP” shown in theNetwork setting,” and then click “LAN IP” shown in the,” and then click “LAN IP” shown in the” and then click “LAN IP” shown in the“LAN IP” shown in theLAN IP” shown in the” shown in theshown in the

list.

Set the VE-PG2’s IP address in Area A.

• Click [Save and Reboot]

after setting.

Enter “192.168.0.2.”192.168.0.2.”.”

BRIDGE MODE APPLICATION

Step 2 [Area A]–Setting IP communication mode

Place the mouse pointer on “Connection setting,” and then click “Operating mode”“Connection setting,” and then click “Operating mode”Connection setting,” and then click “Operating mode”,” and then click “Operating mode”” and then click “Operating mode”“Operating mode”Operating mode””

shown on the list.

Set the IP communication mode for the transceiver A2.

■Unicast mode operation (Continued)

• Click [Save and Reboot]

after setting.

Click to select “UnicastUnicast

mode” option.” option.

BRIDGE MODE APPLICATION 1

Step 3 [Area A]–Setting the IP network connection

Place the mouse pointer on “Connection setting,” and then on “IP network“Connection setting,” and then on “IP networkConnection setting,” and then on “IP network,” and then on “IP network” and then on “IP network

connection,” and then click “Transceiver 1 (TRX1)and then click “Transceiver 1 (TRX1)click “Transceiver 1 (TRX1)“Transceiver 1 (TRX1)Transceiver 1 (TRX1)” shown on the list.

Set the IP address for the transceiver A2.

• Click [Save] after setting.

Enter “192.168.0.3.”192.168.0.3.”.”

BRIDGE MODE APPLICATION

Step 4 [Area A]–Conﬁrming IP network connection

connection,” and then click “Transceiver 1 (TRX1)and then click “Transceiver 1 (TRX1)click “Transceiver 1 (TRX1)“Transceiver 1 (TRX1)Transceiver 1 (TRX1)” shown on the list.