Icom IC-41PRO Einrichtungshandbuch

ADVANCED MANUAL

Iç-41PRO

UHF TRANSCEIVER

IMPORTANT

READ ALL INSTRUCTIONS carefully before using the IC-41PRO UHF transceiver.

KEEP THIS ADVANCED MANUAL, as it contains important operating information that may be useful in the

future.

The BASIC MANUAL is supplied with the transceiver.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain,

Russia, Australia, New Zealand and/or other countries.

TABLE OF CONTENTS

This ADVANCED MANUAL describes the radio as supplied in standard factory default setting. However, the settings

on your transceiver may differ if it has been customised by your dealer. For details, refer to your authorised Icom

dealer or the administrator for your organisations radios.

IMPORTANT.........................................................................i

TABLE OF CONTENTS........................................................i

1. BASIC OPERATION...................................................1–2

PWR ON Password.........................................................1

Keylock............................................................................1

DNon-locked keys.....................................................1

Channel selection ...........................................................1

Zone selection.................................................................2

Priority channel ...............................................................2

DSetting the Priority channel....................................2

DSwitching to the Priority channel............................2

DCancelling the Priority channel ..............................2

Monitor ............................................................................2

Squelch ...........................................................................2

2. SET MODE .................................................................3–6

DSet mode sequence...............................................3

DBacklight ................................................................4

DBeep.......................................................................4

DBeep Level .............................................................4

DChannel Announce ................................................4

DCTCSS/DTCS........................................................4

DVOX ........................................................................4

DVOX Gain ...............................................................4

DVOX Delay (Sec) ....................................................4

DRoger Beep............................................................5

DRinger Level...........................................................5

DSquelch Level.........................................................5

DMic Gain.................................................................5

DBattery Voltage.......................................................5

DSignal Monitor........................................................5

DAuto Power OFF.....................................................5

DPower Save ............................................................5

DLockout ..................................................................6

DScan Stop Timer ....................................................6

DScan Restart ..........................................................6

DPTT Hold................................................................6

DOwn ID...................................................................6

3. REPEATER OPERATION...............................................7

Repeater operation .........................................................7

4. SCAN........................................................................8–10

Scan types ......................................................................8

Scanning preparation......................................................8

DSelecting a scan type.............................................8

DSetting a Tag channel.............................................8

DSetting the Scan Stop Timer ..................................9

Open scan.......................................................................9

Group and Priority scan ..................................................9

Repeater scan...............................................................10

DRepeater scan ﬂow ..............................................10

5. TONE SQUELCH AND POCKET BEEP ................11–12

Tone Squelch ................................................................11

DSetting the

CTCSS tone frequency/DTCS code ................... 11

DTurning ON the Tone Squelch ..............................11

Pocket Beep..................................................................12

DWaiting for a call from a station............................12

6. SELCALL (Selective calling) ................................13–14

Calling ...........................................................................13

DSelecting a TX code.............................................13

DEditing the TX code..............................................13

DTransmitting an individual Selcall.........................13

Receiving ......................................................................14

DReceiving an individual Selcall.............................14

DRecalling a memorised RX code..........................14

DReceiving a Group call.........................................14

Quiet Mode ...................................................................14

Stun function .................................................................14

7. OTHER FUNCTIONS..............................................15–16

Smart Ring and ATS (Automatic Transponder System) ......15

DSmart Ring...........................................................15

DAT S ......................................................................15

RX channels and frequencies .......................................15

DEditing an RX frequency ......................................15

PTT Hold.......................................................................16

Data cloning ..................................................................16

8. SPECIFICATIONS ........................................................17

DGeneral ................................................................17

DTransmitter ...........................................................17

DReceiver...............................................................17

INDEX................................................................................18

Section 1

BASIC OPERATION

PWR ON Password

If the transceiver is set with a power ON password,

enter the password when turning ON the transceiver.

To enter the password, see the illustration below.

The password is a 4 digit code (example: 1234).

➥Push the corresponding keys to enter your password.

• Note that each key represents two digits. That means,

“3764” and “8769” are entered in exactly the same way

(requires no multiple or extended pushing.)

• The entered password will not be displayed.

• If “PASSWD” does not disappear after entering, the

entered password is incorrect. Turn OFF the transceiver,

and then try again.

Hold down for 2 seconds to electronically lock

[ROTARY SELECTOR] and all keys except [PTT],

[Side 1], [TOP], (When in the Function mode) and

to prevent accidental channel changing or function

access.

To lock the keys:

➥Hold down for 2 seconds to lock.

• “ ” is displayed.

To unlock the keys:

➥Hold down for 2 seconds again to unlock.

• “ ” disappears.

DNon-locked keys

Even when the Keylock function is ON, you can use

the following keys for certain conditions.

[PTT]: You can hold down to transmit, and release to

receive.

[Side 1]: You can push to turn the Monitor function ON

or OFF.

[TOP]: You can push to change between Normal

mode and Function mode.

: In the Function mode, you can hold down for

2 seconds to transmit the selected Selcall

code, when a CB channel is selected.

: You can hold down for 2 seconds to turn OFF

the Keylock function.

Keylock

KEY

NUMBER 0

Side 2

[VOL]

[Side 2]

There are 80 UHF CB channels and you have access

to all 80 channels, including designated repeater chan-

nels.You can select between them to communicate with

a speciﬁc person(s). The IC-41PRO is also capable of

being set with an additional 35 receive only channels,

using the optional cs-41PrO clOning sOftware.

➥Rotate [ROTARY SELECTOR] to scroll through the

selectable channels.

Channel selection

BASIC OPERATION

(

Selectable only when more than 2 zones are set, using the

optional CS-41PRO clOning sOftware)

A zone enables you to allocate several channels into

a logical group. This is useful if you want to simplify

communications, particularly in commercial or convoy

applications, or if you want to separate out the receive

only channels to be scanned separately from CB

channels.

qPush [TOP] to enter the Function mode.

wHold down for 2 seconds to enter the zone

selection mode.

eRotate [ROTARY SELECTOR] to select the desired

zone, and then push to set.

NOTE:

• The transceiver remains in the selected mode when

turned OFF and then ON again.

• CB-05, CB-R05 and CB-35 channels are for emergency

use, and are required to be left open for only emergency

use. CB-22 and CB-23 are used for only receiving.

Zone selection

The Priority channel enables you to have quick access

to a speciﬁc channel. Only one channel can be set as

the Priority channel. “P” is displayed when the Priority

channel is set.

DSetting the Priority channel

qRotate [ROTARY SELECTOR] to select a desired

channel.

wHold down for 2 seconds to set the selected

channel as the Priority Channel.

• “P” is displayed.

DSwitching to the Priority channel

➥Push to switch from a displayed channel to the

Priority channel. “N/A” is displayed when the Priority

channel is not set.

DCancelling the Priority channel

➥Push [TOP] to enter the Function mode, and then

hold down for 2 seconds to cancel the Priority

channel setting.

• “P” disappears.

Priority channel

Monitor

The Monitor function opens the Squelch or Tone

squelch, enabling you to receive weak signals. This

enables quick access to the open squelch setting.

➥To turn the Monitor function ON or OFF, push [Side 1].

• “MONI ON” or “MONI OF” is displayed when the function

is turned ON or OFF.

Squelch

In order to clearly receive signals, set the squelch

level to suit your environment. This eliminates

background noise when there are no signals preset.

A higher level is better for inner cities or noisy areas,

and a lower level is more beneﬁcial in quiet, rural or

country areas.

Setting the squelch level:

qPush [Side 2] to enter the squelch setting mode.

wRotate [ROTARY SELECTOR] to set the squelch

level to between 0 and 9.

• 0= lowest squelch level, 9= highest squelch level

ePush [Side 2] to set the selected squelch level and

exit the setting mode.

Information

You can also set the squelch level in the Set mode.

See page 5 for details.

Section 2SET MODE

In the Set mode, you can change various transceiver

settings to suit your operating requirements.

qHold down [TOP] for 2 seconds to enter the Set

mode.

• If no key is pushed for 30 seconds, the transceiver will

return to the normal mode.

wPush [Side 1] or [Side 2] to select an item.

• You can also select an item by pushing [TOP].

eRotate [ROTARY SELECTOR] to select an option in

the selected item.

r Hold down [TOP] for 2 seconds to set and exit the

Set mode, or simply turn OFF the transceiver.

Own ID

Your Own ID is omitted from the Set mode sequence

by default. You can set this item using the optional

CS-41PRO clOning sOftware.

VOX related items

The following items are displayed in the Set mode

only when the optional HM-168LWP sPeaker

micrOPhOne or other optional external device is

connected to the transceiver. See the BASIC

MANUAL for external device connection details.

• VOX

• VOX Gain

• VOX Delay (Sec)

DSet mode sequence

The diagram below describes the sequence of the items in the Set mode.

• The sequence is as shown below when you push [Side 1] in the Set mode.

• Lockout

• Power Save

• Signal Monitor

• Battery Voltage

• Squelch Level

• CTCSS/DTCS

• Auto Power OFF

• Mic Gain

• Beep Level

• Beep

• Roger Beep

• Scan Restart

• Scan Stop Timer

• Backlight

Starting item

• PTT Hold

• Ringer Level

• Channel Announce

2SET MODE

DBacklight

The transceiver features a backlit LCD display to use in

low-light conditions.

You can select the backlight mode in the Set mode.

ON: Backlight is continuously ON.

A2: Lights for 5 seconds when STATUS INDICA-

TOR changes, or when you push any key except

[PTT].

AT: Lights for 5 seconds when you transmit or re-

ceive a Selcall signal, or when you push any key

except [PTT].

OF:No backlight.

Backlight Auto (default) Backlight ON

Beep ON (default) Beep OFF

Beep level 3 (default) Beep level 1

Channel Announce OFF (default) Channel Announce ON

DBeep Level

You can set the volume level for the key beeps to be-

tween 1 and 5, or 1(Linked) and 5(Linked).

When a linked level is set, you can adjust the Beep

Level by rotating [VOL].

DBeep

The conﬁrmation beep is set to ON as the default.

You can turn OFF the beep for silent operation in the

Set mode.

DChannel Announce

You can turn this function ON to announce the select-

ed channel number.

• When Beep is set to OFF, there will not be an announcement,

regardless of this setting.

DVOX

(Displayed only when an optional external device is

connected to the transceiver)

This function automatically switches between receiving

and transmitting mode by detecting your voice.

DCTCSS/DTCS

Select the desired CTCSS tone frequency or DTCS

code.

You can change between CTCSS and DTCS setting

modes by pushing .

See page 11 for more information about CTCSS and

DTCS.

CTCSS tone frequency

setting mode (default)

DTCS code setting mode

VOX function ON (default) VOX function OFF

VOX Gain level 5 (default) VOX Gain level 8

DVOX Gain

(Displayed only when an optional external device is

connected to the transceiver)

Set the VOX Gain level to between 1 and 10. Higher

gain makes the VOX function more sensitive to your

voice.

DVOX Delay (Sec)

(Displayed only when an optional external device is

connected to the transceiver)

VOX Delay is the period of time between when you

stop speaking and the transceiver stops transmitting

and then returns to receive. Set it to between 0.5 and

3.0 seconds.

NOTE:

If you set the time too short, a pause in speaking

will be regarded as the end of your conversation

and the transceiver will return to receive, even if you

continue speaking.

VOX Delay

0.5 seconds (default)

VOX Delay 2.0 seconds

2SET MODE

DRoger Beep

You can turn ON the Roger Beep function to beep to

indicate that the transmission has ended.

DRinger Level

You can set the Ringer Level to between 1 and 5, or 1

(Linked) and 5 (Linked).

When a linked level is set, you can adjust the Ringer

Level by rotating [VOL].

NOTE: You need to set the Beep function to ON

before setting the Ringer Level. (p. 4)

Ringer Level 3 (default) Ringer Level 5

Ringer Level 3 (Linked) Ringer Level 5 (Linked)

DSquelch Level

The Squelch circuit eliminates background noise when

no signals are present.

Set the level to where the noise just disappears, for

proper operation.

A higher level is better for inner cities or noisy areas,

and a lower level is more beneﬁcial in quiet, rural or

country areas. (0=lowest, 9=highest)

Squelch Level 3 (default) Squelch Level 0

DMic Gain

You can adjust the microphone sensitivity to between

1 (minimum sensitivity) and 4 (maximum sensitivity).

With a higher sensitivity, the microphone picks up

softer voices, though it may pick up more ambient

noise.

Mic Gain

sensitivity 2 (default)

Mic Gain sensitivity 1

Roger Beep OFF (default) Roger Beep ON

DBattery Voltage

You can set to display the Battery Voltage for 2

seconds, when you turn ON the transceiver.

Battery Voltage

OFF (default)

Battery Voltage ON

DSignal Monitor

You can select whether or not to mute a Selcall code

signal, DTMF code signal or Roger Beep emission.

ON: Unmuted

OFF: Muted

Signal Monitor ON (default) Signal Monitor OFF

DAuto Power OFF

You can set the transceiver to automatically turn OFF

after a set period without any key opertion.

You can set it to between 0.5 and 4.0 hours (0.5 hour

steps) or 8.0 hours.

Auto Power OFF

is OFF (default)

2 hour setting

DPower Save

The Power Save function reduces the current drain by

deactivating the receiver circuit if a signal is not received,

or the transceiver is not used for 5 seconds.

The receiver periodically reactivates, checks for any

signals, and deactivates according to a preset timer

setting.

Power Save ON (default) Power Save OFF

2SET MODE

DLockout

Select the transmission Lockout function mode which

temporarily inhibits transmission.

• RP (Repeater Lockout): Locks out a repeater.

• BU (Busy Lockout): Locks out a busy channel.

• OF (OFF): Turns OFF the function.

Lockout OFF (default) Repeater Lockout setting

DScan Stop Timer

You can set the Scan Stop Timer to pause (P5) or timer

scan (5/10/15).

When a signal disappears, the scan resumes after the

set period of time. (p. 9)

5/10/15: Scan pauses for 5, 10 or 15 seconds when

a signal is detected, then resumes.

P5: Scan pauses until the signal disappears,

and then resumes after 5 seconds

(Recommended setting).

Scan Stop Timer

P5 (default)

10 second setting

DScan Restart

This function restarts the scan 10 seconds after you

stop transmitting.

You can turn the function ON or OFF.

Scan Restart OFF (default) Scan Restart ON

DPTT Hold

You can use the PTT switch as a one-touch PTT

switch (push once between transmit and receive).

You can transmit without holding down [PTT] using this

function. Transmission automatically stops after 3

minutes in this mode.

PTT Hold function

OFF (default)

PTT Hold function ON

DOwn ID

(

You can only set this item after enabling the function

using the optional CS-41PRO clOning sOftware.

)

This function enables you to allocate your Own ID

which identiﬁes you as a target for Selcall operation

and allows tracking of the origin of transmissions.

Editing your Own ID:

When your Own ID is displayed, hold down for 2

seconds to enter the editing mode.

w Rotate [ROTARY SELECTOR] until the desired

number is displayed on the blinking digit.

e Push to set the blinking digit and go to the next

digit.

r Repeat steps wand euntil all 5 digits are set, and

then push again to save the Own ID.

Section 3REPEATER OPERATION

Repeater operation

Repeaters extend the operational range of the transceiver by retransmitting the signals it receives. Repeaters are

usually located on the top of a building or a mountain, as the elevation increases their effectiveness, allowing the user

to transmit and receive over greater distances. During Simplex operation, transceivers transmit and receive on the

same frequency. During Duplex operation (using a repeater) transceivers transmit and receive on different frequen-

cies. It automatically does this when one of the repeater channels is selected.

Repeater

RPT-06

Uplink —— Channel 36

(Transmitting)

Downlink — Channel 6

(Receiving)

Accessing a repeater:

To use a repeater,you need to select a repeater channel (Repeater CH 1 to 8, and 41 to 48).

You can search for any accessible repeaters in your local area by using the Repeater scan. (p. 10)

➥Rotate [ROTARY SELECTOR] to select a repeater channel.

• “DUP” is displayed.

Section 4SCAN

Scan types

The transceiver has 4 scan types, a Tag function and 4

Resume options, for scanning versatility.

Tagged channels are independently set for Open,

Group and Priority scans. All channels may be preset

as tagged channels for all scans.

Repeatedly checks the preset Priority

channel after scanning 5 tagged channels.

Priority

channel

GROUP and PRIORITY SCAN

ch 01

ch 02 ch 03 ch 04

ch 05

ch 10

ch 09 ch 08 ch 07

ch 06

★★★

★★

Repeatedly scans all tagged channels in sequence.

ch 40

ch 01 ch 02 ch 03

ch 04

ch 05

ch 06ch 39

OPEN SCAN

★★★

★★

★

Ch 02

Ch 02Ch 01

Scan cancel

Ch 48

Ch 01

Ch 03Ch 04

Ch 48

★★

★

★★

★

REPEATER SCAN

Scans all repeater channels (01 to 08 and 41 to 48)* in

sequence. If there are no busy channels after scanning

channels 01 to 08 and 41 to 48,* the scan begins from 01

again, and then the transceiver transmits a signal to

search for a repeater while scanning.

* Excludes emergency repeater 05.

The IC-41PRO scans all tagged channels when a scan is

activated. When it detects a busy channel, the scan can

be set to pause, or to resume after a pause. (Except for

a Repeater scan).

• See page 6 for details on the Scan Restart function.

DSelecting a scan type

➥Push several times to select the desired scan type.

• Select Open, Group or Priority scan.

Push

Open scan is selected.

Group scan is selected.

Priority scan is selected.

Push

Displayed

Scanning preparation

DSetting a Tag channel

Before setting tag channels, you must select the desired

scan type, as described above.

NOTE: All channels for each scan type are tagged by

default. To select the channels to scan, you must ﬁrst

untag the undesired channels.

qSelect the desired scan type.

wRotate [ROTARY SELECTOR] to select the undesired

channel.

eHold down for 2 seconds to untag the selected

channel.

• “S” disappears when the tag setting is OFF.

DisplayedDisappears

rRepeat steps qto euntil all the undesired channels

are untagged.

To tag

qRotate [ROTARY SELECTOR] to select an untagged

channel.

wHold down for 2 seconds to tag the selected

channel.

• “S” is displayed when the selected channel is tagged.

Andere Handbücher für IC-41PRO

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-M411 Bedienungsanleitung

Icom

Icom IC-725 Bedienungsanleitung

Icom

Icom IC-F14/S Bedienungsanleitung

Icom

Icom IC-F7010T Bedienungsanleitung

Icom

Icom IC-281A Bedienungsanleitung

Icom

Icom IC-M710RT Bedienungsanleitung

Icom

Icom IC-756 Bedienungsanleitung

Icom

Icom IC-737 Bedienungsanleitung

Icom

Icom ID-5100A Montageanleitung

Icom

Icom A25C SPORT 66 USA Stücklistenhandbuch

Icom

Icom IC-3SAT Bedienungsanleitung

Icom

Icom IC-F510 Bedienungsanleitung

Icom

Icom IC-7100 Bedienungsanleitung

Icom

Icom IC-M423GE Bedienungsanleitung

Icom

Icom IC-F3400D Bedienungsanleitung

Icom

Icom IC-F8100 Bedienungsanleitung

Icom

Icom IC-M35 Bedienungsanleitung

Icom

Icom IC-F11S Bedienungsanleitung

Icom

Icom IC-M1EURO V Bedienungsanleitung

Icom

Icom IC-F50V Bedienungsanleitung

Icom

Icom IC-F6121D Bedienungsanleitung

Icom

Icom IC-47A Bedienungsanleitung

Icom

Icom IC-M604A Bedienungsanleitung

Icom

Icom IC-H11 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung