Icom IC-7300 Bedienungsanleitung

Andere Handbücher für IC-7300

12

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-A14IC-A14S Bedienungsanleitung

Icom

Icom IC-7610 Installationsanleitung

Icom

Icom IC-4GAT Bedienungsanleitung

Icom

Icom IC-4088A Leitfaden

Icom

Icom IC-A14 Bedienungsanleitung

Icom

Icom ID-5100A Bedienungsanleitung

Icom

Icom IC-U8S1 Bedienungsanleitung

Icom

Icom iF5062D Bedienungsanleitung

Icom

Icom IC-E92D Bedienungsanleitung

Icom

Icom IC-20 Bedienungsanleitung

Icom

Icom IC-A24E Bedienungsanleitung

Icom

Icom IC-M1EURO V Bedienungsanleitung

Icom

Icom IC-M304 Bedienungsanleitung

Icom

Icom IC-F62D Bedienungsanleitung

Icom

Icom IC-M32 Bedienungsanleitung

Icom

Icom IC-M35 Bedienungsanleitung

Icom

Icom IC-T22A Bedienungsanleitung

Icom

Icom IC-F1721 Bedienungsanleitung

Icom

Icom iC-F5012 Bedienungsanleitung

Icom

Icom IC-201 Bedienungsanleitung

Icom

Icom IC-A110 Bedienungsanleitung

Icom

Icom IC-7000 Bedienungsanleitung

Icom

Icom IC-3210A Bedienungsanleitung

Icom

Icom IC-A200 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

ICOM –IC7300 –QUICK START OPERATING GUIDE

By K7HCP

The ICOM IC-7300 is an HF + 6 meter, multi-mode, self-contained Software

Defined Radio (SDR) transceiver with knobs, buttons and a touch screen. It also

has a real-time spectrum display with pan adapter and water fall displays.

It stands alone and does not require attachment to a computer to function like

most SDR radios in the past.

However to operate this radio using digital mode computer software such as

WSJT-X (FT8) or DigiPan (PSK31) all that is required is a single USB cable with NO

other digital interface hardware required such as sound card interface device.

GETTING STARTED:

Press the POWER button

Turn the AF gain to 9 o-clock

Turn the RF gain/Sql to 12 o-clock

Turn the MAIN DIAL (the big knob) to change frequency

To change Bands:

Touch the MHz frequency display area of the touch screen (touch the “7”of 7.073)

To change Mode:

Touch the Mode area displayed on the touch screen (touch the “LSB”)

To change Filters:

Touch the Filter area displayed on the touch screen (touch the “Fil2”)

To display the Scope:

Press the M.Scope button located below the display to display the small spectrum scope.

Press and Hold the M.Scope button located below the display to display the large spectrum

scope.

NOTE: The “Multi -”Function Control Knob”located just to the right of the display and near the top of

the radio. This knob is used the make selections from various lists of options from time to time.

Press the Multi button, then touch the desired selection. Then turn the knob to choose your setting.

Finally press the button to exit.

To change Frequency:

There are several ways to change the current frequency of the transceiver:

1. Turn the Main Dial (the big knob)

2. While displaying the Spectrum Scope, touch the area of a desired signal spike.

The scope display area touched will be magnified.

Touch the magnified area again and the transceiver will change frequency corresponding to

the frequency of the desired signal.

3. Using pre stored Memories:

Press the MENU button

Then press the MEMORIES button

Then rotate the MULTI knob to select the desired memory channel

Then touch the desired memory channel to choose your selection.

To display the Meters:

Press the MENU button

Then press the METER button